scholarly journals Numerical study of the physical processes of gas leakage in the compression ring in diesel engines

2021 ◽  
Vol 2118 (1) ◽  
pp. 012016
Author(s):  
J A Pabón León ◽  
J P Rojas Suárez ◽  
M S Orjuela Abril
Keyword(s):  
Numerical Model ◽  
Internal Combustion Engines ◽  
Numerical Study ◽  
Cylinder Liner ◽  
Combustion Engines ◽  
Combustion Gases ◽  
Gas Leakage ◽  
Lubrication Film ◽  
Compression Ring ◽  
Complex Mathematical Model

Abstract In this research, the construction of a numerical model is proposed for the analysis of the friction processes and the thickness of the lubrication film present in the compression ring of internal combustion engines. The model is built using MATLAB software, and three load conditions are used as reference (2 Nm, 4 Nm, and 6 Nm) with a rotation speed of 3600 rpm, which correspond to a stationary single-cylinder diesel engine. Comparison between model estimates and experimental results show that the development model could predict the actual engine conditions. The deviation between the numerical model and the experimental data was 17%. It was shown that the increase in engine load causes a 16% increase in the friction force of the compression ring, which implies a 50% increase in power loss due to friction processes. In general, the model developed allows the analysis of the friction processes in the compression ring and its effect on the lubrication film, considering the leakage of the combustion gases. In this way, the construction of a more complex mathematical model is achieved, which allows improving the precision in the analyzes related to the interaction between the compression ring and the cylinder liner.

scholarly journals Enhancing the Geometrical Performance Using Initially Conical Cylinder Liner in Internal Combustion Engines—A Numerical Study

2020 ◽  
Vol 10 (11) ◽  
pp. 3705
Author(s):  
Ahmad Alshwawra ◽  
Florian Pohlmann-Tasche ◽  
Frederik Stelljes ◽  
Friedrich Dinkelacker
Keyword(s):  
Internal Combustion Engines ◽  
Thermal Stresses ◽  
Numerical Study ◽  
Cylinder Liner ◽  
Internal Combustion ◽  
Friction Reduction ◽  
Cylindrical Shape ◽  
Combustion Engines ◽  
Cold State ◽  
The Impact

Reducing friction is an important aspect to increase the efficiency of internal combustion engines (ICE). The majority of frictional losses in engines are related to both the piston skirt and piston ring–cylinder liner (PRCL) arrangement. We studied the enhancement of the conformation of the PRCL arrangement based on the assumption that a suitable conical liner in its cold state may deform into a liner with nearly straight parallel walls in the fired state due to the impact of mechanical and thermal stresses. Combining the initially conical shape with a noncircular cross section will bring the liner even closer to the perfect cylindrical shape in the fired state. Hence, a significant friction reduction can be expected. For the investigation, the numerical method was first developed to simulate the liner deformation with advanced finite element methods. This was validated with given experimental data of the deformation for a gasoline engine in its fired state. In the next step, initially conically and/or elliptically shaped liners were investigated for their deformation between the cold and fired state. It was found that, for liners being both conical and elliptical in their cold state, a significant increase of straightness, parallelism, and roundness was reached in the fired state. The combined elliptical-conical liner led to a reduced straightness error by more than 50% compared to the cylindrical liner. The parallelism error was reduced by 60% to 70% and the roundness error was reduced between 70% and 80% at different liner positions. These numerical results show interesting potential for the friction reduction in the piston-liner arrangement within internal combustion engines.

Numerical Study of Piston Skirt-Liner Lubrication Considering the Effects of Deformation in Internal Combustion Engines

2012 ◽  
Author(s):  
Lipu Ning ◽  
Xianghui Meng ◽  
Youbai Xie
Keyword(s):  
Elastic Deformation ◽  
Internal Combustion Engines ◽  
Numerical Study ◽  
Cylinder Liner ◽  
Internal Combustion ◽  
Combustion Engines ◽  
Surface Geometry ◽  
Piston Skirt ◽  
Lubrication Performance ◽  
Liner System

This paper presents a comprehensive lubrication model for piston skirt-liner system of internal combustion engines. In the model it is included that the effects of the surface roughness, the piston skirt surface geometry, the piston pin offset, the crankshaft offset, and the lubricant viscosity on the piston secondary motion and lubrication performance. Especially, the effects of the thermal and the elastic deformation of the piston skirt and the cylinder liner, and the piston skirt deformations due to the combustion pressure and the piston axial inertia, are considered as the key task in this study. The results show that the combustion force, the working temperature and the piston axial inertia all play important roles in the piston-skirt lubrication. Also, considering the elastic deformation of the piston skirt and the cylinder liner is beneficial to the prediction of piston-skirt lubrication more accurately. The developed program in this study can provide a useful tool for the analysis of the piston-liner system lubrication problem.

scholarly journals The Rotating Liner Engine (RLE) Diesel Prototype: Reducing Internal Engine Friction by about 40% under Idle Conditions

2021 ◽  
Vol 11 (2) ◽  
pp. 779
Author(s):  
Dimitrios Dardalis ◽  
Amiyo Basu ◽  
Matt J. Hall ◽  
Ronald D. Mattthews
Keyword(s):  
Internal Combustion Engines ◽  
Hydrodynamic Lubrication ◽  
Cylinder Liner ◽  
Friction Reduction ◽  
Contact Boundary ◽  
Metal Contact ◽  
Load Testing ◽  
Gas Leakage ◽  
Brake Mean Effective Pressure ◽  
Economy Benefit

The Rotating Liner Engine (RLE) concept is a design concept for internal combustion engines, where the cylinder liner rotates at a surface speed of 2–4 m/s in order to assist piston ring lubrication. Specifically, we have evidence from prior art and from our own research that the above rotation has the potential to eliminate the metal-to-metal contact/boundary friction that exists close to the piston reversal areas. This frictional source becomes a significant energy loss, especially in the compression/expansion part of the cycle, when the gas pressure that loads the piston rings and skirts is high. This paper describes the Diesel RLE prototype constructed from a Cummins 4BT and the preliminary observations from initial low load testing. The critical technical challenge, namely the rotating liner face seal, appears to be operating with negligible gas leakage and within the hydrodynamic lubrication regime for the loads tested (peak cylinder pressures of the order of 100 bar) and up to about 10 bar BMEP (brake mean effective pressure). Preliminary testing has proven that the metal-to-metal contact in the piston assembly mostly vanished, and a friction reduction at idle conditions of about 40% as extrapolated to a complete engine has taken place. It is expected that as the speed increases, the friction reduction percentage will diminish, but as the load increases, the friction reduction will increase. The fuel economy benefit over the US Heavy-Duty driving cycle will likely be of the order of 10% compared to a standard engine.

Oxygen Sensor Testing for Automotive Applications

2020 ◽  
Vol 896 ◽  
pp. 249-254
Author(s):  
Dragos Tutunea ◽  
Ilie Dumitru ◽  
Oana Victoria Oţăt ◽  
Laurentiu Racila ◽  
Ionuţ Daniel Geonea ◽  
...  
Keyword(s):  
Internal Combustion Engines ◽  
Oxygen Sensor ◽  
Oxygen Sensors ◽  
Pollutant Emissions ◽  
Combustion Engines ◽  
Automotive Applications ◽  
Combustion Gases ◽  
Experimental Stand ◽  
Residual Oxygen ◽  
Sensor Degradation

During the operation of internal combustion engines the air-fuel ratio (A/F) is an important parameter which affects fuel consumption and pollutant emissions. The automotive oxygen sensor (Lambda) measures the quantity of residual oxygen in the combustion gases. Sensor degradation in time due to the exposure to high temperatures causes a distortion in controlling the A/F with the increase in gas emissions. In this paper an experimental stand is designed to test oxygen sensor degradation in laboratory condition. Four oxygen sensors were tested function of temperature and time recording their variation in resistance and voltage. The results showed similar values in the curves for all sensors tested.

Cavitation erosion and wear behaviour of a boron cast iron cylinder liner under bio-fuel conditions

RSC Advances ◽  
2016 ◽  
Vol 6 (83) ◽  
pp. 79968-79970 ◽  
Author(s):  
Yufu Xu ◽  
Lulu Yao ◽  
Bin Zhang ◽  
Ka Tang ◽  
Bao Li ◽  
...  
Keyword(s):  
Cast Iron ◽  
Internal Combustion Engines ◽  
Cavitation Erosion ◽  
Cylinder Liner ◽  
Internal Combustion ◽  
Wear Behaviour ◽  
Combustion Engines ◽  
Near Future

The use of renewable bio-fuel in internal combustion engines is the trend for the near future.

Numerical Study of Piston Skirt-Liner Elastohydrodynamic Lubrication and Contact by the Multigrid Method

2010 ◽  
Author(s):  
Xianghui Meng ◽  
Youbai Xie
Keyword(s):  
Contact Problem ◽  
Internal Combustion Engines ◽  
Multigrid Method ◽  
Numerical Study ◽  
Elastohydrodynamic Lubrication ◽  
Cylinder Liner ◽  
Piston Skirt ◽  
Liner System ◽  
Tribological Analysis ◽  
Quasi Newton

The cylinder liner-piston system of internal combustion engines is one of the key friction pairs running at the most rigor working conditions. Under the influence of elastohydrodynamic lubrication and contact between the piston skirt and the liner, the dynamic process of piston is a nonlinear and stiff problem difficult to be analyzed accurately and easily. To reach a stable and rapid convergence in analysis, the MEBDF method and the multigrid method are used to solve the piston-skirt elastohydrodynamic lubrication and contact problem. Firstly the solving process of the piston dynamics is analyzed based on the MEBDF method. Then the residual equations for the elastohydrodynamic lubrication pressure are built based on the multigrid method. And the solving method of the nonlinear residual equations is presented based on the quasi Newton-Raphson method. Finally the numerical simulation program is developed based on the MEBDF method and the multigrid method. The elastohydrodynamic lubrication and contact problem of the piston skirt-liner system is simply analyzed based on the simulation. The study in this paper can provide an effective method for tribological analysis and optimization of piston–liner system in the future.

scholarly journals Modeling the Fatigue Wear of the Cylinder Liner in Internal Combustion Engines during the Break-In Period and Its Impact on Piston Ring Lubrication

Lubricants ◽  
2019 ◽  
Vol 7 (10) ◽  
pp. 89
Author(s):  
Chongjie Gu ◽  
Renze Wang ◽  
Tian Tian
Keyword(s):  
Internal Combustion Engines ◽  
Cylinder Liner ◽  
Internal Combustion ◽  
Asperity Contact ◽  
Combustion Engines ◽  
Fatigue Wear ◽  
Wear Model ◽  
Surface Finishes ◽  
Liner Surface ◽  
Piston Ring Lubrication

In internal combustion engines, a significant portion of the total fuel energy is consumed to overcome the mechanical friction between the cylinder liner and the piston rings. The engine work loss through friction gradually reduces during the engine break-in period, as the result of liner surface topography changes caused by wear. This work is the first step toward the development of a physics-based liner wear model to predict the evolution of liner roughness and ring pack lubrication during the break-in period. Two major mechanisms are involved in the wear model: plastic deformation and asperity fatigue. The two mechanisms are simulated through a set of submodels, including elastoplastic asperity contact, crack initiation, and crack propagation within the contact stress field. Compared to experimental measurements, the calculated friction evolution of different liner surface finishes during break-in exhibits the same trend and a comparable magnitude. Moreover, the simulation results indicate that the liner wear rate or duration of break-in depends greatly on the roughness, which may provide guidance for surface roughness design and manufacturing processes.

Sign in / Sign up

Export Citation Format

Share Document