scholarly journals Utilization of copper fiber waste to increase compressive strength and split tensile strength of rigid pavement

2021 ◽  
Vol 878 (1) ◽  
pp. 012052
Author(s):  
H Ndruru ◽  
R M Simanjuntak ◽  
S P Tampubolon
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Surface Layer ◽  
Concrete Slab ◽  
Residential Areas ◽  
Split Tensile Strength ◽  
Rigid Pavement ◽  
Traffic Loads ◽  
Pavement Construction ◽  
Low Traffic

Abstract The rigid pavement is a pavement construction in which a concrete slab is used as the top layer, which is located above the foundation or directly above the subgrade, without or with an asphalt surface layer. One type of rigid pavement used in Indonesia is rigid pavement without using reinforcement which is usually used in areas with low traffic or residential areas. Pavement without using reinforcement is the small split tensile strength so that the part of the plate will experience cracks due to stresses that cannot be avoided from traffic loads. Therefore, it is necessary to have reinforcement on the concrete slab so that the cracks do not extend. In this research, the use of copper fiber waste from electronic cables as a substitute solution for reinforcement to be used as a mixture in concrete. The experiments were carried out using fiber with variations of 0%, 0.5%, 1%, and 1.5% of the total weight of concrete mixture material and then tested at 28 days of concrete age. This research showed the variation of fiber weight until 1,5% increase the split tensile strength up to 32,46% and the compressive strength up to 9,16%.

Investigating Alternates to Flexural Beams for Airport Concrete Strength Compliance

2021 ◽  
Author(s):  
Greg White ◽  
Matthew Johnson
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Concrete Strength ◽  
Acceptance Testing ◽  
Rigid Pavement ◽  
Indirect Tensile ◽  
Curing Condition ◽  
Pavement Construction ◽  
Flexural Beam

Concrete for airport rigid pavement construction is generally specified to achieve a minimum characteristic flexural strength of 4.5 MPa and acceptance testing during construction aims to verify this key design assumption. The large flexural beam specimens are cumbersome and the testing is expensive. Consequently, industry desires a more convenient test and a laboratory-based conversion to an estimated flexural strength for acceptance testing during production. This research developed and trialed a protocol for the conversion of indirect tensile strength and compressive strength to estimate the flexural strength. The laboratory correlation was encouraging. However, when trialed on a real construction project, the conversions significantly underestimated the measured flexural strength and the risk of rejecting compliant batches of concrete was significantly higher. Further research is required to understand why the reliable conversions developed in the laboratory failed in the field. This may be related to the effect of ambient temperature on 28 day flexural strength, despite the constant curing condition.

scholarly journals Effect of Recycled Coarse Aggregates in Properties of Concrete

2008 ◽  
Vol 3 (4) ◽  
pp. 130-137 ◽  
Author(s):  
R Kumutha ◽  
K Vijai
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Coarse Aggregate ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Split Tensile Strength ◽  
Coarse Aggregates ◽  
The Cost

The properties of concrete containing coarse recycled aggregates were investigated. Laboratory trials were conducted to investigate the possibility of using recycled aggregates from the demolition wastes available locally as the replacement of natural coarse aggregates in concrete. A series of tests were carried out to determine the density, compressive strength, split tensile strength, flexural strength and modulus of elasticity of concrete with and without recycled aggregates. The water cement ratio was kept constant for all the mixes. The coarse aggregate in concrete was replaced with 0%, 20%, 40%, 60%, 80% and 100% recycled coarse aggregates. The test results indicated that the replacement of natural coarse aggregates by recycled aggregates up to 40% had little effect on the compressive strength, but higher levels of replacement reduced the compressive strength. A replacement level of 100% causes a reduction of 28% in compressive strength, 36% in split tensile strength and 50% in flexural strength. For strength characteristics, the results showed a gradual decrease in compressive strength, split tensile strength, flexural strength and modulus of elasticity as the percentage of recycled aggregate used in the specimens increased. 100% replacement of natural coarse aggregate by recycled aggregate resulted in 43% savings in the cost of coarse aggregates and 9% savings in the cost of concrete.

scholarly journals Compression and Split Tensile Characteristics of Concrete Containing Quarry Residues

2019 ◽  
Vol 5 (5) ◽  
pp. 1-5
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Research Facility ◽  
River Sand ◽  
Split Tensile Strength ◽  
Fine Aggregates ◽  
Concrete Production ◽  
The World ◽  
Substitute Material ◽  
Quarry Dust

Waterway sand and pit sand are the most normally utilized fine aggregates for concrete creation in many parts of the world. Huge scale extraction of these materials presents genuine ecological risk in numerous parts of the nation. Aside from the ecological danger, there still exists the issue of intense lack in many regions. In this way, substitute material in place of river sand for concrete production should be considered. The paper means to examine the compressive and split tensile qualities of concrete produced using quarry residue, sand, and a blend of sand and quarry dust. The experimentation is absolutely research facility based. A total of 60 concrete cubes of size 150 mm x 150 mm x 150 mm, and 60 cylinders 150 mm in diameter and 300 mm deep, conforming to M50 grade were casted. All the samples were cured and tested with a steady water/concrete proportion of 0.31. Out of the 60 blocks cast, 20 each were made out of natural river sand, quarry dust and an equivalent blend of sand and quarry dust. It was discovered that the compressive strength and split tensile strength of concrete produced using the blend of quarry residue and sand was higher than the compressive qualities of concrete produced using 100% sand and 100% quarry dust.

scholarly journals Physical Properties of Concrete Containing Graphene Oxide Nanosheets

Materials ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1707 ◽  
Author(s):  
Yu-You Wu ◽  
Longxin Que ◽  
Zhaoyang Cui ◽  
Paul Lambert
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Graphene Oxide ◽  
Flexural Strength ◽  
Portland Cement ◽  
Physical Properties ◽  
Ordinary Portland Cement ◽  
Construction Materials ◽  
Split Tensile Strength ◽  
Cement Pastes

Concrete made from ordinary Portland cement is one of the most widely used construction materials due to its excellent compressive strength. However, concrete lacks ductility resulting in low tensile strength and flexural strength, and poor resistance to crack formation. Studies have demonstrated that the addition of graphene oxide (GO) nanosheet can effectively enhance the compressive and flexural properties of ordinary Portland cement paste, confirming GO nanosheet as an excellent candidate for using as nano-reinforcement in cement-based composites. To date, the majority of studies have focused on cement pastes and mortars. Only limited investigations into concretes incorporating GO nanosheets have been reported. This paper presents an experimental investigation on the slump and physical properties of concrete reinforced with GO nanosheets at additions from 0.00% to 0.08% by weight of cement and a water–cement ratio of 0.5. The study demonstrates that the addition of GO nanosheets improves the compressive strength, flexural strength, and split tensile strength of concrete, whereas the slump of concrete decreases with increasing GO nanosheet content. The results also demonstrate that 0.03% by weight of cement is the optimum value of GO nanosheet dosage for improving the split tensile strength of concrete.

scholarly journals Effect of Glass Fibers on Self Compacting Concrete

2020 ◽  
Vol 170 ◽  
pp. 06018
Author(s):  
Sandeep L. Hake ◽  
S. S. Shinde ◽  
Piyush K. Bhandari ◽  
P. R. Awasarmal ◽  
B. D. Kanawade
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Glass Fibers ◽  
Extreme Condition ◽  
High Dispersion ◽  
Self Compacting Concrete ◽  
Split Tensile Strength ◽  
Glass Fiber Reinforced ◽  
Complex Structural

Self Compacting Concrete (SCC) is a specially developed concrete for concreting under extreme condition of inaccessibility from heights. It is capable to flow under influence of its own weight. It could be used when encountered with dense reinforcement and complex structural design. Problem of segregation as well as bleeding is eliminated and vibration is not required for compaction. As concrete is strong in compression and weak in tension. Hence to make it strong in tension, discontinuous Anti-Crack high dispersion glass fibers are added. SCC mix prepared with addition of discontinuous glass fibers is called as Glass Fiber reinforced Self Compacting Concrete (GFRSCC). In this paper an experimental study has been carried out to check the effect of Anti-Crack high dispersion glass fibers on the compressive strength, split tensile strength and flexural strength of SCC. The result show that, as compared to the Normal SCC, the compressive strength of GFRSCC increases by 2.80% and 12.42%, the split tensile strength of GFRSCC increases by 4.47% and 25.12% and the flexural strength of SCC increases by 6.57% and 14.34% when the Cem-FIL Anti-Crack HD glass fibers were added as 0.25% and 0.50% respectively by the weight of total cementitious material contents. The addition of 0.25% Cem-FIL Anti-Crack HD glass fibers to SCC has not much affect on the workability of Normal SCC. Whereas, addition of 0.50% Cem-FIL Anti-Crack HD glass fibers reduces the workability of SCC.

scholarly journals Studies on Pumice Lightweight Aggregate Concrete with Quarry Dust Using Mathematical Modeling Aid of ACO Techniques

2016 ◽  
Vol 2016 ◽  
pp. 1-12 ◽  
Author(s):  
J. Rex ◽  
B. Kameshwari
Keyword(s):  
Mathematical Modeling ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Lightweight Aggregate ◽  
Optimization Techniques ◽  
Lightweight Aggregate Concrete ◽  
Split Tensile Strength ◽  
Rock Aggregate ◽  
Quarry Dust

The lightweight aggregate is an aggregate that weighs less than the usual rock aggregate and the quarry dust is a rock particle used in the concrete for the experimentation. The significant intention of the proposed technique is to frame a mathematical modeling with the aid of the optimization techniques. The mathematical modeling is done by minimizing the cost and time consumed in the case of extension of the real time experiment. The proposed mathematical modeling is utilized to predict four output parameters such as compressive strength (Mpa), split tensile strength (Mpa), flexural strength (Mpa), and deflection (in mm). Here, the modeling is carried out with three different optimization techniques like genetic algorithm (GA), particle swarm optimization (PSO), and ant colony optimization (ACO) with 80% of data from experiment utilized for the training and the remaining 20% for the validation. Finally, while testing, the error value is minimized and the performance obtained in the ACO for the parameters such as compressive strength, split tensile strength, flexural strength, and deflection is 91%, 98%, 87%, and 94% of predicted values, respectively, in the mathematical modeling.

Polyester Fibers in the Concrete an Experimental Investigation

2011 ◽  
Vol 261-263 ◽  
pp. 125-129 ◽  
Author(s):  
Venu Malagavelli ◽  
Neelakanteswara Rao Paturu
Keyword(s):  
Experimental Investigation ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
Crack Resistance ◽  
Industrial Waste ◽  
Fiber Reinforced Concrete ◽  
Split Tensile Strength ◽  
Biodegradable Waste ◽  
Polyester Fibers

Construction field has experienced a growing interest in Fiber Reinforced Concrete (FRC) due to its various advantages. The disposal of industrial waste especially non biodegradable waste is creating a lot of problems in the environment. In the present investigation, an attempt has been made by using non biodegradable waste (polyester fibers) in the concrete to improve the crack resistance and strength. Concrete having compressive strength of 25MPa is used for this study. Samples were prepared by using various fiber contents starting from 0 to 6% of with an increment of 0.5% for finding Compressive strength, split tensile strength and flexural strengths. It is observed that, compressive strength, split tensile strength and flexural strengths of concretes is increasing as the fiber content is increased up to some extent.

scholarly journals Tests on workability and strength of high strength-flowable concrete containing PET waste fiber

2020 ◽  
Vol 7 (3) ◽  
pp. 115-139
Author(s):  
Sarkawt Karim ◽  
◽  
Azad Mohammed ◽  
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fiber Length ◽  
High Strength ◽  
Fiber Reinforced Concrete ◽  
Time Increase ◽  
Fiber Volume ◽  
Split Tensile Strength ◽  
Pet Waste ◽  
Strength Tests

This study describes two workability tests, compressive strength and tensile strength tests of high strength flowable concrete containing plastic fiber prepared from polyethylene terephthalate (PET) waste bottles. For the high fluidity mix Vebe time and V-funnel time tests were carried out. Results show that there is a Vebe time increase with PET fiber addition to concrete being increased with increasing fiber volume and fiber length. V-funnel time was found to reduce when up to 0.75% fiber volume is added to concrete, followed by an increase for larger fiber volumes. When fiber length is increase, there is more time increase, but in general, V-funnel time increase was lower than that of Vebe time, indicating a different influence of PET fiber on the compatibility and flowability. The measured V-funnel time for all mixes was found to conform to the limits of European specifications on the flowability of self compacting concrete. Small descending in compressive strength was recorded for RPET fiber reinforced concrete that reached 15.74 % for 1.5 percent fiber content with 10 mm fiber length. Attractive results was recorded in split tensile strength of RPET fibrous samples which resulted in improvement up to 63.3 % for 1.5 percent of 40 mm fiber length content.

scholarly journals Mechanical Behaviour on Replacement of Aggregate by E-waste in Concrete

2019 ◽  
Vol 9 (2) ◽  
pp. 302-305 ◽  
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Mechanical Behaviour ◽  
Coarse Aggregate ◽  
Environmental Problems ◽  
Waste Utilization ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Construction Work ◽  
Split Tensile Strength

Concrete is a widely used material in all construction work. The aim of the project is to study the behavior of concrete with replacement of E waste. The fine aggregate and coarse aggregate are naturally available due to increase in demand it is over exploited. The waste utilization is sustainable solution to environmental problems Waste from electric and electronic equipment is used as an E waste replacement for coarse aggregate in concrete which is used in the construction .Therefore the effects have been made to study the use of E waste components as a partial replacement of coarse aggregate in 5%, 10% and 15%. To determine the optimum percentage of E waste that can be replaced for coarse aggregate the compressive strength and split tensile strength of concrete to be studied. After determining the optimum percentage of E waste that can be replaced with coarse aggregate. The comparison of the conventional and optimum percentage of E waste replaced with concrete has been done

Sign in / Sign up

Export Citation Format

Share Document