scholarly journals Studies on Pumice Lightweight Aggregate Concrete with Quarry Dust Using Mathematical Modeling Aid of ACO Techniques

2016 ◽  
Vol 2016 ◽  
pp. 1-12 ◽  
Author(s):  
J. Rex ◽  
B. Kameshwari
Keyword(s):  
Mathematical Modeling ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Lightweight Aggregate ◽  
Optimization Techniques ◽  
Lightweight Aggregate Concrete ◽  
Split Tensile Strength ◽  
Rock Aggregate ◽  
Quarry Dust

The lightweight aggregate is an aggregate that weighs less than the usual rock aggregate and the quarry dust is a rock particle used in the concrete for the experimentation. The significant intention of the proposed technique is to frame a mathematical modeling with the aid of the optimization techniques. The mathematical modeling is done by minimizing the cost and time consumed in the case of extension of the real time experiment. The proposed mathematical modeling is utilized to predict four output parameters such as compressive strength (Mpa), split tensile strength (Mpa), flexural strength (Mpa), and deflection (in mm). Here, the modeling is carried out with three different optimization techniques like genetic algorithm (GA), particle swarm optimization (PSO), and ant colony optimization (ACO) with 80% of data from experiment utilized for the training and the remaining 20% for the validation. Finally, while testing, the error value is minimized and the performance obtained in the ACO for the parameters such as compressive strength, split tensile strength, flexural strength, and deflection is 91%, 98%, 87%, and 94% of predicted values, respectively, in the mathematical modeling.

Performance of Lightweight Aggregate Concrete Containing Expanded Polystyrene, Cinder and Ground-Granulated Blast-Furnace Slag

2020 ◽  
Vol 17 (9) ◽  
pp. 4304-4310
Author(s):  
M. L. Harish ◽  
H. Narendra ◽  
Md. Azam Afzal
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Lightweight Aggregate ◽  
Normal Weight ◽  
Expanded Polystyrene ◽  
Lightweight Aggregate Concrete ◽  
Split Tensile Strength ◽  
Aggregate Concrete ◽  
Optimal Mix

Lightweight aggregate concrete is developed by substituting normal weight aggregate either fully or partially based on strength and density required. Expanded polystyrene (EPS) bead is a type of low density material, which also has good energy-absorbing characteristics and can be used as light weight aggregate in concrete. In the present study, Structural lightweight aggregate concrete (SLWAC) was produced by fully replacing normal weight aggregate with combinations of EPS beads to Cinder by the ratio 20:80, 40:60, 60:40, 80:20 respectively. And GGBS was used as supplementary cementitious material. The resulting concrete had strength variation between 29.5 to 11.6 MPa, and the density variation of 2192 to 1701 kg/m3. Considering strength and density criteria 40:60 ratios was observed as the optimal mix. The Compressive strength acquired by concrete was inversely proportional to the volume of EPS beads. Effect of fibers on mechanical properties such as flexural strength, compressive strength, and split-tensile strength was studied on the optimal mix by using polypropylene fibers, it was observed that an 8.78% increase in flexural strength at 1% fibers, 16.5% increase in Compressive strength at 0.5% fibers, and 35.4% increase in split-tensile strength at 1% fibers. Along with this, durability tests such as water absorption and permeability tests were performed, the performance of this concrete in water absorption test is well within the limits but in permeability, it underperformed which confirms that as the EPS ratio in the concrete increased, the absorption and depth of penetration values increased considerably. Microscopic observations were also made to study the interface amongst the cement paste and aggregates. It was revealed that GGBS did not influence significantly on the bonding with EPS beads.

scholarly journals Flexural Behaviour of RCC Beams Partially Replacing Cement by Dolomite Powder and Sand by Quarry Dust

2019 ◽  
Vol 8 (12) ◽  
pp. 5280-5290
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
Flexural Strength ◽  
Concrete Beams ◽  
Low Cost ◽  
Waste Material ◽  
Reinforced Concrete Beams ◽  
Split Tensile Strength ◽  
Quarry Dust

The present Investigation is aimed at utilizing low cost material Dolomite powder and waste material Quarry dust as partial replacement of cement and sand in concrete. This experimental investigation is carried out in three stages. In 1st stage M25 grade of concrete is produced by replacing cement by 0%, 6%, 12% and 18% of Dolomite Powder. In 2nd Stage concrete is produced by keeping the optimum 12% of dolomite powder as constant and sand is replaced by quarry dust in the percentage of 0%, 25%, 35% and 45%. In 3rd stage the optimum percentage of Dolomite Powder and Quarry Dust (DP+QD) Concrete are used to determine the compressive strength, split tensile strength and flexural strength of concrete and to check the flexural behavior of RCC beams. It is found that the concrete made of low cost material dolomite powder and waste material quarry dust increases the compressive strength, split tensile strength and flexural strength of concrete when compared to that of normal concrete. It also concluded that the first crack load and ultimate load of dolomite powder and quarry dust reinforced concrete beams increases when compared with normal reinforced concrete beams. From study it is concluded that the low cost material Dolomite powder & Quarry dust can be used in construction works which results in construction cost. By using natural resources the environment is protected.

Mechanical Properties of Lightweight Alum Sludge Aggregate Concrete

2015 ◽  
Vol 754-755 ◽  
pp. 413-416 ◽  
Author(s):  
Nur Quraatu’ Aini Mohd Rajin ◽  
Roszilah Hamid
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Lightweight Concrete ◽  
Lightweight Aggregate ◽  
Lightweight Aggregate Concrete ◽  
Content Increase ◽  
Split Tensile Strength ◽  
Aggregate Concrete ◽  
Alum Sludge ◽  
Better Than

Disposal of alum sludge (AS) in such an economical and environmental friendly way is a major challenge that water treatment plants around the globe had to deal with. AS cannot be dumped into landfills as it contains heavy metals which are harmful to the environment. In this study, alum sludge is utilised as partial replacements (0, 5 and 10%) of natural granite coarse aggregate (by mass) to form a lightweight concrete. The water/cement ratio is 0.65. The water absorption of the alum sludge is 22.06%. The slump, density, compressive strength and split tensile strength of the lightweight alum sludge aggregate concrete (LASAC) reduce as the AS aggregate content increase. The density of the 10% AS aggregate concrete is 2185.3 kg/m3. The compressive strength reduced from 25.6 MPa to 16.7 MPa and 14.2 MPa at 0, 5 and 10% replacement of AS aggregate respectively. The 2.18 MPa tensile strength of the control concrete reduced to 1.53 MPa at 10% replacement of AS aggregate. But as for the flexural strength, it increases from 5.42 MPa for the control up to 5.55 MPa and 5.63 MPa for 5 and 10% replacement of AS aggregate respectively. Results show that strength of alum sludge lightweight aggregate concrete is better than lightweight crumb tyre aggregate concrete and is at par with oil palm coconut shell aggregate concrete.

Performance of Lightweight Aggregate Concrete Containing Expanded Polystyrene, Cinder and Silica Fume

2020 ◽  
Vol 17 (9) ◽  
pp. 4311-4317
Author(s):  
M. L. Harish ◽  
H. Narendra ◽  
Md. Rizwan Tahashildar
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Silica Fume ◽  
Lightweight Aggregate ◽  
Normal Weight ◽  
Expanded Polystyrene ◽  
Lightweight Aggregate Concrete ◽  
Split Tensile Strength ◽  
Aggregate Concrete ◽  
Optimal Mix

Lightweight aggregate concrete is developed by substituting normal weight aggregate either fully or partially based on required strength and density. Expanded polystyrene (EPS) bead is a type of low density material, which also has good energy-absorbing characteristics and can be used as light weight aggregate in concrete. In the present study, Structural lightweight aggregate concrete (SLWAC) was produced by fully replacing normal weight aggregate with combinations of EPS beads to Cinder by the ratio 20:80, 40:60, 60:40, 80:20 respectively and Silica fume was used as supplementary cementitious material. The resulting concrete had strength variation between 24.85 to 12.01 MPa, and the density variation of 1896 to 1664 kg/m3. Considering strength and density criteria 40:60 ratios was observed as the optimal mix. The Compressive strength acquired by concrete was inversely proportional to the volume of EPS beads. Effect of fibres on mechanical properties such as flexural strength, compressive strength, and split-tensile strength was investigated on optimal mix by using polypropylene fibres, it was observed that a 13.24% increase in flexural strength at 1% fibres, 8.41% increase in Compressive strength at 1% fibres and 23.11% increase in split-tensile strength at 1% fibres. Along with these, durability tests such as water absorption and permeability tests were performed, the performance of this concrete in water absorption test and permeability is well within the acceptable limits as the EPS ratio in the concrete increased, the absorption and depth of penetration values increased considerably. Microscopic observations were also made to study the interface amongst the cement paste and aggregates. It was revealed that silica fume has influenced significantly in bonding with EPS beads.

Mechanical Properties of Fiber Reinforced Lightweight Aggregate Concrete

2011 ◽  
Vol 477 ◽  
pp. 274-279 ◽  
Author(s):  
Yi Xu ◽  
Lin Hua Jiang ◽  
Hong Qiang Chu ◽  
Lei Chen
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Water Hyacinth ◽  
Steel Fiber ◽  
Polypropylene Fiber ◽  
Lightweight Aggregate ◽  
Splitting Tensile Strength ◽  
Lightweight Aggregate Concrete ◽  
Fiber Types

In this study, the effects of fiber types on the mechanical properties of lightweight aggregate concretes were investigated. Three types of fibers, namely, polypropylene fiber, steel fiber and water hyacinth (Eichhornia crassipes) fiber, and two types of lightweight aggregates, namely, expanded polystyrene and ceramsite were used. The compressive strength and splitting tensile strength of concretes were tested. The results show that both the compressive strength and the splitting tensile strength were improved by adding a reasonable volume of steel fiber and polypropylene fiber into LWAC. The addition of water hyacinth fiber had little effect on the compressive strength of LWAC, while a little increase was observed in the splitting tensile strength.

scholarly journals Effect of Recycled Coarse Aggregates in Properties of Concrete

2008 ◽  
Vol 3 (4) ◽  
pp. 130-137 ◽  
Author(s):  
R Kumutha ◽  
K Vijai
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Coarse Aggregate ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Split Tensile Strength ◽  
Coarse Aggregates ◽  
The Cost

The properties of concrete containing coarse recycled aggregates were investigated. Laboratory trials were conducted to investigate the possibility of using recycled aggregates from the demolition wastes available locally as the replacement of natural coarse aggregates in concrete. A series of tests were carried out to determine the density, compressive strength, split tensile strength, flexural strength and modulus of elasticity of concrete with and without recycled aggregates. The water cement ratio was kept constant for all the mixes. The coarse aggregate in concrete was replaced with 0%, 20%, 40%, 60%, 80% and 100% recycled coarse aggregates. The test results indicated that the replacement of natural coarse aggregates by recycled aggregates up to 40% had little effect on the compressive strength, but higher levels of replacement reduced the compressive strength. A replacement level of 100% causes a reduction of 28% in compressive strength, 36% in split tensile strength and 50% in flexural strength. For strength characteristics, the results showed a gradual decrease in compressive strength, split tensile strength, flexural strength and modulus of elasticity as the percentage of recycled aggregate used in the specimens increased. 100% replacement of natural coarse aggregate by recycled aggregate resulted in 43% savings in the cost of coarse aggregates and 9% savings in the cost of concrete.

scholarly journals Compression and Split Tensile Characteristics of Concrete Containing Quarry Residues

2019 ◽  
Vol 5 (5) ◽  
pp. 1-5
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Research Facility ◽  
River Sand ◽  
Split Tensile Strength ◽  
Fine Aggregates ◽  
Concrete Production ◽  
The World ◽  
Substitute Material ◽  
Quarry Dust

Waterway sand and pit sand are the most normally utilized fine aggregates for concrete creation in many parts of the world. Huge scale extraction of these materials presents genuine ecological risk in numerous parts of the nation. Aside from the ecological danger, there still exists the issue of intense lack in many regions. In this way, substitute material in place of river sand for concrete production should be considered. The paper means to examine the compressive and split tensile qualities of concrete produced using quarry residue, sand, and a blend of sand and quarry dust. The experimentation is absolutely research facility based. A total of 60 concrete cubes of size 150 mm x 150 mm x 150 mm, and 60 cylinders 150 mm in diameter and 300 mm deep, conforming to M50 grade were casted. All the samples were cured and tested with a steady water/concrete proportion of 0.31. Out of the 60 blocks cast, 20 each were made out of natural river sand, quarry dust and an equivalent blend of sand and quarry dust. It was discovered that the compressive strength and split tensile strength of concrete produced using the blend of quarry residue and sand was higher than the compressive qualities of concrete produced using 100% sand and 100% quarry dust.

scholarly journals Physical Properties of Concrete Containing Graphene Oxide Nanosheets

Materials ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1707 ◽  
Author(s):  
Yu-You Wu ◽  
Longxin Que ◽  
Zhaoyang Cui ◽  
Paul Lambert
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Graphene Oxide ◽  
Flexural Strength ◽  
Portland Cement ◽  
Physical Properties ◽  
Ordinary Portland Cement ◽  
Construction Materials ◽  
Split Tensile Strength ◽  
Cement Pastes

Concrete made from ordinary Portland cement is one of the most widely used construction materials due to its excellent compressive strength. However, concrete lacks ductility resulting in low tensile strength and flexural strength, and poor resistance to crack formation. Studies have demonstrated that the addition of graphene oxide (GO) nanosheet can effectively enhance the compressive and flexural properties of ordinary Portland cement paste, confirming GO nanosheet as an excellent candidate for using as nano-reinforcement in cement-based composites. To date, the majority of studies have focused on cement pastes and mortars. Only limited investigations into concretes incorporating GO nanosheets have been reported. This paper presents an experimental investigation on the slump and physical properties of concrete reinforced with GO nanosheets at additions from 0.00% to 0.08% by weight of cement and a water–cement ratio of 0.5. The study demonstrates that the addition of GO nanosheets improves the compressive strength, flexural strength, and split tensile strength of concrete, whereas the slump of concrete decreases with increasing GO nanosheet content. The results also demonstrate that 0.03% by weight of cement is the optimum value of GO nanosheet dosage for improving the split tensile strength of concrete.

scholarly journals Effect of Glass Fibers on Self Compacting Concrete

2020 ◽  
Vol 170 ◽  
pp. 06018
Author(s):  
Sandeep L. Hake ◽  
S. S. Shinde ◽  
Piyush K. Bhandari ◽  
P. R. Awasarmal ◽  
B. D. Kanawade
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Glass Fibers ◽  
Extreme Condition ◽  
High Dispersion ◽  
Self Compacting Concrete ◽  
Split Tensile Strength ◽  
Glass Fiber Reinforced ◽  
Complex Structural

Self Compacting Concrete (SCC) is a specially developed concrete for concreting under extreme condition of inaccessibility from heights. It is capable to flow under influence of its own weight. It could be used when encountered with dense reinforcement and complex structural design. Problem of segregation as well as bleeding is eliminated and vibration is not required for compaction. As concrete is strong in compression and weak in tension. Hence to make it strong in tension, discontinuous Anti-Crack high dispersion glass fibers are added. SCC mix prepared with addition of discontinuous glass fibers is called as Glass Fiber reinforced Self Compacting Concrete (GFRSCC). In this paper an experimental study has been carried out to check the effect of Anti-Crack high dispersion glass fibers on the compressive strength, split tensile strength and flexural strength of SCC. The result show that, as compared to the Normal SCC, the compressive strength of GFRSCC increases by 2.80% and 12.42%, the split tensile strength of GFRSCC increases by 4.47% and 25.12% and the flexural strength of SCC increases by 6.57% and 14.34% when the Cem-FIL Anti-Crack HD glass fibers were added as 0.25% and 0.50% respectively by the weight of total cementitious material contents. The addition of 0.25% Cem-FIL Anti-Crack HD glass fibers to SCC has not much affect on the workability of Normal SCC. Whereas, addition of 0.50% Cem-FIL Anti-Crack HD glass fibers reduces the workability of SCC.

scholarly journals Production of lightweight Geopolymer concrete using artificial local lightweight aggregate

2018 ◽  
Vol 162 ◽  
pp. 02024
Author(s):  
Waleed Abbas ◽  
Wasan Khalil ◽  
Ibtesam Nasser
Keyword(s):  
Thermal Conductivity ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Lightweight Concrete ◽  
Lightweight Aggregate ◽  
Experimental Tests ◽  
Pulse Velocity ◽  
Dry Density ◽  
Geopolymer Concrete

Due to the rapid depletion of natural resources, the use of waste materials and by-products from different industries of building construction has been gaining increased attention. Geopolymer concrete based on Pozzolana is a new material that does not need the presence of Portland cement as a binder. The main focus of this research is to produce lightweight geopolymer concrete (LWGPC) using artificial coarse lightweight aggregate which produced from locally available bentonite clays. In this investigation, the binder is low calcium fly ash (FA) and the alkali activator is sodium hydroxide and sodium silicate in different molarities. The experimental tests including workability, fresh density, also, the compressive strength, splitting tensile strength, flexural strength, water absorption and ultrasonic pulse velocity at the age of 7, 28 and 56 days were studied. The oven dry density and thermal conductivity at 28 days age are investigated. The results show that it is possible to produce high strength lightweight geopolymer concrete successfully used as insulated structural lightweight concrete. The 28-day compressive strength, tensile strength, flexural strength, dry density, and thermal conductivity of the produced LWGPC are 35.8 MPa, 2.6MPa, 5.5 MPa, 1835kg/m3, and 0.9567 W/ (m. K), respectively.

Sign in / Sign up

Export Citation Format

Share Document