scholarly journals Preliminary Study on Hand-cast Lightweight Concrete Block using Raw Rice Husk as Aggregate

2021 ◽  
Vol 933 (1) ◽  
pp. 012005
Author(s):  
S Winarno
Keyword(s):  
Compressive Strength ◽  
Rice Husk ◽  
Laboratory Experiments ◽  
Lightweight Concrete ◽  
Concrete Block ◽  
Rice Husks ◽  
Mix Proportion ◽  
Concrete Blocks ◽  
Preliminary Study ◽  
Preliminary Application

Abstract Raw rice husk is an abundantly available waste material in Indonesia as one of rice producing countries. Due to rice husk is light in weight and convex in shape, this paper presents a preliminary application of raw rice husk as natural aggregate in order to make lightweight concrete blocks. Concrete specimens contained Portland Cement, filler, and raw rice husk, in which the mix proportion was in volumetric ratio, i.e 1.25 cement and 2.75 filler constantly, whereas dosage of rice husk varied from 8.5 to 10. The production of the concrete block was by mixing the ingredients together and then the mixture was casted and compacted on moulds by hand manually. Series laboratory experiments were accomplished to analyse the compressive strength and density. For this, four groups of mixes were prepared. The results have shown that the higher proportion of rice husk is the lower its compressive strength and the lighter its density. At proportion of 1,25 cement: 2,75 fillers: 8,5 raw rice husks, the compressive strength is 26.64 kg/cm2 and this satisfies the minimum standard (25 kg/cm2). Unfortunately, the density is 1,536.73 kg/m3 and it is higher than the maximum standard of 1,400 kg/m3. Thus, it is important to research further by making and testing some improved specimens with more cement, more rice husk, and less filler to fulfil strength and density.

Preliminary Study of Pressed Lightweight Geopolymer Block Using Fly Ash, Portland Cement and Recycled Lightweight Concrete

2016 ◽  
Vol 718 ◽  
pp. 184-190
Author(s):  
Patcharapol Posi ◽  
Piyawat Foytong ◽  
Pearploy Thongjapo ◽  
Natakorn Thamultree ◽  
Phongsathon Boontee ◽  
...  
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Lightweight Concrete ◽  
Concrete Block ◽  
Concrete Aggregate ◽  
Fine Aggregate ◽  
Geopolymer Concrete ◽  
Lignite Fly Ash ◽  
Concrete Blocks ◽  
Preliminary Study

In this research, the properties of pressed lightweight fly ash geopolymer concrete block containing Portland cement and recycled lightweight concrete aggregate. The recycled lightweight concrete aggregate (RLCA) was crushed and classified as coarse aggregate (CA), medium aggregate (MA) and fine aggregate (FA). The RLCA with CA : MA : FA of 30 : 30 : 40 by weight was used to reduce the weight of concrete block. Lightweight geopolymer concrete block was produced from lignite fly ash, NaOH, Na2SiO3, RCLA and PC. The lightweight geopolymer concrete blocks with 28-day compressive strengths between 2.0 and 14.1 MPa and densities between 1130 and 1370 kg/m3 were obtained.

THE INFLUENCE OF MICROWAVE INCINERATED RICE HUSK ASH ON FOAMED CONCRETE WORKABILITY AND COMPRESSIVE STRENGTH USING TAGUCHI METHOD

2015 ◽  
Vol 75 (1) ◽  
Author(s):  
Ridho Bayuaji
Keyword(s):  
Compressive Strength ◽  
Taguchi Method ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Lightweight Concrete ◽  
Technical Requirement ◽  
Pozzolanic Material ◽  
Mix Proportion ◽  
Strength Based ◽  
Foamed Concrete

Foamed concrete is lightweight concrete with a green material concept. One of cement-based materials is Microwave Incinerated Rice Husk Ash (MIRHA) foamed concrete (FC) as a pozzolanic material, that is interesting to be studies since the information about the ingredient can be used to understand the product behaviors. This study is more focused on the investigation towards the effect of composer of MIRHA FC on the workability and compressive strength. The mix proportion of the MIRHA FC here was designed by means of Taguchi method with L16 orthogonal array through five parameters (MIRHA contents, water cementitious ratio (w/c), sand cement ratio (s/c), superplasticizer (SP) content, and foam content). The mixtures were tested both in fresh and hardened states to fulfill the technical requirement of FC. It was also supported by the analysis on the characteristics of concretes including its workability and compressive strength. Based on the analysis, it is shown MIRHA is capable of enhancing FC workability and strength.  

scholarly journals Preliminary Study on the Utilization of RHA as a Performance Enhancer for Rubber Mortar

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3216
Author(s):  
Jin Li ◽  
Peiyuan Chen ◽  
Haibing Cai ◽  
Ying Xu ◽  
Chunchao Li
Keyword(s):  
Compressive Strength ◽  
Mechanical Strength ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Capillary Absorption ◽  
Optimal Dosage ◽  
Positive Effects ◽  
Waste Rubber ◽  
Chloride Resistance ◽  
Preliminary Study

In this study, rice husk ash (RHA) was explored as a strength enhancer for mortars containing waste rubber. The effects of RHA on the flow, mechanical strength, chloride resistance, and capillary absorption of rubber mortar were investigated by substituting up to 20% cement with RHA. The experimental results showed that the incorporation of rubber into mortar could be safely achieved by adding RHA as a cement substitute by up to 20% without compromising the compressive strength of mortar. Moreover, the RHA also exerted positive effects on the enhancement of the chloride resistance as well as the capillary absorption of rubber mortars, for which 15% RHA was found to be the optimal dosage.

scholarly journals Strength and Durability Performance of Alkali-Activated Rice Husk Ash Geopolymer Mortar

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
Yun Yong Kim ◽  
Byung-Jae Lee ◽  
Velu Saraswathy ◽  
Seung-Jun Kwon
Keyword(s):  
Compressive Strength ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Polymerization Reaction ◽  
Strength Development ◽  
Geopolymer Concrete ◽  
Portland Cement Concrete ◽  
Mix Proportion ◽  
Strength And Durability ◽  
Alkali Activated

This paper describes the experimental investigation carried out to develop the geopolymer concrete based on alkali-activated rice husk ash (RHA) by sodium hydroxide with sodium silicate. Effect on method of curing and concentration of NaOH on compressive strength as well as the optimum mix proportion of geopolymer mortar was investigated. It is possible to achieve compressive strengths of 31 N/mm2and 45 N/mm2, respectively for the 10 M alkali-activated geopolymer mortar after 7 and 28 days of casting when cured for 24 hours at 60°C. Results indicated that the increase in curing period and concentration of alkali activator increased the compressive strength. Durability studies were carried out in acid and sulfate media such as H2SO4, HCl, Na2SO4, and MgSO4environments and found that geopolymer concrete showed very less weight loss when compared to steam-cured mortar specimens. In addition, fluorescent optical microscopy and X-ray diffraction (XRD) studies have shown the formation of new peaks and enhanced the polymerization reaction which is responsible for strength development and hence RHA has great potential as a substitute for ordinary Portland cement concrete.

Experimental Research on Compressive Strength of Self-Compacting Concrete with Recycled Coarse Aggregates

2011 ◽  
Vol 306-307 ◽  
pp. 1084-1087 ◽  
Author(s):  
Jing Li ◽  
Xian Feng Qu ◽  
Lin Fu Wang ◽  
Chong Qing Zhu ◽  
Juan Li
Keyword(s):  
Compressive Strength ◽  
Design Method ◽  
Self Compacting Concrete ◽  
Longitudinal Splitting ◽  
Coarse Aggregates ◽  
Hydraulic Concrete ◽  
Mix Proportion ◽  
Splitting Failure ◽  
Concrete Blocks ◽  
Waste Solid

In order to study cubic compressive strength of recycled coarse aggregates-filled concrete systematically, recycled coarse aggregates with the particle size from 50 to150mm are made from waste solid contents, which are artificially broken from abandoned rubble and concrete blocks. Based on the mix proportion design method of ordinary concrete and test code for hydraulic concrete, 3 groups of recycled coarse aggregates-filled concrete cubic specimens were prepared and the compressive strength of the specimens were tested. The results showed that basic failure pattern of recycled coarse aggregates-filled concrete are longitudinal splitting failure, and that cubic compressive strength is higher than that of self-compacting concrete.

scholarly journals Use of Recycled Tyre Rubber in Non-structural Concrete

2018 ◽  
Vol 203 ◽  
pp. 06001
Author(s):  
Muhammad Bilal Waris ◽  
Hussain Najwani ◽  
Khalifa Al-Jabri ◽  
Abdullah Al-Saidy
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Coarse Aggregate ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Structural Concrete ◽  
Cement Ratio ◽  
Mix Proportion ◽  
Water To Cement Ratio ◽  
Concrete Blocks

To manage tyre waste and conserve natural aggregate resource, this research investigates the use of waste tyre rubber as partial replacement of fine aggregates in non-structural concrete. The research used Taguchi method to study the influence of mix proportion, water-to-cement ratio and tyre rubber replacement percentage on concrete. Nine mixes were prepared with mix proportion of 1:2:4, 1:5:4 and 1:2.5:3; water-to-cement ratio of 0.25, 0.35 and 0.40 and rubber to fine aggregate replacement of 20%, 30% and 40%. Compressive strength and water absorption tests were carried out on 100 mm cubes. Compressive strength was directly proportional to the amount of coarse aggregate in the mix. Water-to-cement ratio increased the strength within the range used in the study. Strength was found to be more sensitive to the overall rubber content than the replacement ratio. Seven out of the nine mixes satisfied the minimum strength requirement for concrete blocks set by ASTM. Water absorption and density for all mixes satisfied the limits applicable for concrete blocks. The study indicates that mix proportions with fine to coarse aggregate ratio of less than 1.0 and w/c ratio around 0.40 can be used with tyre rubber replacements of up to 30 % to satisfy requirements for non-structural concrete.

scholarly journals Comparative Strength and Cost of Rice Husk Concrete Block

2019 ◽  
Vol 280 ◽  
pp. 04002
Author(s):  
Setya Winarno
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Rice Husk ◽  
Concrete Block ◽  
Strength Analysis ◽  
Normal Concrete ◽  
Comparative Cost ◽  
Concrete Production ◽  
Sustainable Materials ◽  
The Cost

This research presents a comparative cost and strength analysis of rice husk concrete block which is aimed at reducing the cost of concrete production and emphasizing environmentally and friendly sustainable materials. Concrete block materials consist of cement, filler, and rice husk. Tests were performed to compare the strength and cost of seven cement rice husk weight ratios designated ranging from 0.67 to 2.00 with constant water cement ration of 0.4. Samples have been tested for 28-day strength. The analysis of the results has showed that the higher proportions of rice husk correspond to decreased strength dan cost polynomially. At 134% proportion of rice husk, it is optimum value for rice husk concrete block. In this point, the compressive strength satisfies the standard. Also, water absorption of 16,04% justifies the maximum standard. Overall, the cost of 134% RH concrete is Rp 511,809 per m3 which is 42.5% cheaper than normal concrete block.

scholarly journals Hydrochloric Acid Pretreatment of Different Types of Rice Husk Ash Influence on the Properties of Cement Paste

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1524 ◽  
Author(s):  
Jing Liu ◽  
Chunyan Xie ◽  
Chao Fu ◽  
Xiuli Wei ◽  
Dake Wu
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Cement Paste ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Control Sample ◽  
Control Group ◽  
Rice Husks ◽  
Acid Pretreatment ◽  
Blank Control Group

When properly processed, rice husk ash (RHA) comprises a large amount of SiO2, which exhibits a high pozzolanic activity and acts as a good building filler. In this paper, the effects of rice husk ash content, acid pretreatment, and production regions on the compressive and flexural properties and water absorption of a cement paste were studied. The experimental results showed that the compressive strength of the rice husk ash was the highest with a 10% content level, which was about 16.22% higher than that of the control sample. The rice husk after acid pretreatment displayed a higher strength than that of the sample without the acid treatment, and the rice husk from the Inner Mongolia region indicated a higher strength than that from the Guangdong province. However, the flexural strength of each group was not significantly different from that of the blank control group. The trend observed for the water absorption was similar to that of the compressive strength. The variation in the RHA proportions had the greatest influence on the properties of the paste specimens, followed by the acid pretreatments of the rice husks. The production regions of the rice husks indicated the least influence.

scholarly journals Properties and Internal Curing of Concrete Containing Recycled Autoclaved Aerated Lightweight Concrete as Aggregate

2017 ◽  
Vol 2017 ◽  
pp. 1-11 ◽  
Author(s):  
Teewara Suwan ◽  
Pitiwat Wattanachai
Keyword(s):  
Compressive Strength ◽  
Lightweight Concrete ◽  
Value Added ◽  
Aggregate Size ◽  
Lightweight Aggregate ◽  
Normal Weight ◽  
Green Technology ◽  
Internal Curing ◽  
Low Carbon ◽  
Mix Proportion

Global warming is a vital issue addressed to every sector worldwide, including the construction industry. To achieve the concept of green technology, many attempts have been carried out to develop low-carbon footprint products. In the construction sector, Autoclaved Aerated Concrete (AAC) has become more popular and been manufactured to meet the construction demand. However, errors from manufacturing process accounted for approximately 3 to 5% of the AAC production. The development of AAC waste as lightweight aggregate in concrete is one of the potential approaches which was extendedly studied in this paper. The results showed that the compressive strength of AAC-LWA concrete was decreased with an increase in volume and coarse size. The optimum mix proportion was the AAC aggregate size of 1/2′′ to 3/8′′ with 20 to 40% replacement to normal weight aggregate. Internal curing by AAC-LWA was also observed and found to provide sufficient water inside the specimens, leading to an achievement in higher compressive strength. The main goal of this study is not only utilising unwanted wastes from industry (recycling of waste materials) but also building up a new knowledge of using AAC-LWA as an internal curing agent as well as the production of value-added lightweight concrete products.

scholarly journals Mix Proportion of Lightweight Straw Ceramsite Concrete

CONVERTER ◽  
2021 ◽  
pp. 110-117
Author(s):  
Yanxia Huang
Keyword(s):  
Compressive Strength ◽  
Lightweight Concrete ◽  
Concrete Strength ◽  
Engineering Application ◽  
Volumetric Method ◽  
Comprehensive Utilization ◽  
Mix Proportion ◽  
Concrete Mix ◽  
Straw Burning ◽  
The Impact

To reduce air pollution of straw burning, and also to improve the ratio of straw comprehensive utilization, this paper presents a lightweight concrete with straw based on the mix proportion research. Firstly, the mix proportion of lightweight ceramsite concrete was designed by a volumetric method. Then, a series of lightweight ceramsite concrete mix proportion experiments were conducted to verify the validity of the design and to evaluate the effect of the admixtures on the performance of the concrete. Finally, the lightweight straw ceramsite concrete mix proportion experiments were conducted by adding straw to lightweight ceramsite concrete for studying the impact of the straw amount on the concrete strength and density. The experimental results show that the compressive strength of lightweight straw ceramsite concrete can reach the requirement of engineering application. The concrete strength and density were descended obviously with the increasing of straw amount. It was suggested that the straw amount should be limited in 20% of the concrete volume.

Sign in / Sign up

Export Citation Format

Share Document