scholarly journals Is it possible to turn a diesel engine into a less pollutant device?

2022 ◽  
Vol 960 (1) ◽  
pp. 012010
Author(s):  
Cosmin Constantin Suciu ◽  
Ioana Ionel ◽  
Daniel Ostoia ◽  
Nicolae Stelian Lontis ◽  
Ion Vetres ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Diesel Engines ◽  
Combustion Engine ◽  
Pollution Level ◽  
Engine Control ◽  
Start Of Injection ◽  
Injection Quantity ◽  
Measurement Results ◽  
Before And After ◽  
Parameters Measurement

Abstract The current tendency in the eastern part of Europe is to modify old diesel engines with the purpose of improving characteristics in terms of horsepower and torque, but also to reduce the generated pollution. The diesel engines are still in use, against to the tendencies of renouncing to their support, at least in larger urban & industrial areas, where the pollution level, especially the particulate matter (particles PM10, PM2.5) and ozone concentrations, also the NOx are supposed to be generated mostly by diesel engine vehicles. The paper presents results concerning the influence of modifying the diesel engine control unit’s parameters, such as injection quantity, start of injection, intake air pressure and all the others correlated for better performance. The article brings into attention possibilities to reduce the exhaust pollution concentrations, correlated by simultaneous ways of improving the external characteristics of the engine by modifying the engine control unit’s parameters. Measurement results of a compression ignited internal combustion engine before and after the retrofitting, by reparametrization, meaning changing the parameters are presented and discussed.

scholarly journals Virtual Calibration Method for Diesel Engine by Software in The Loop Techniques

2019 ◽  
Vol 16 (3) ◽  
pp. 6940-6957
Author(s):  
M. C. Cameretti ◽  
E. Landolfi ◽  
T. Tesone ◽  
A. Caraceni
Keyword(s):  
Diesel Engine ◽  
Fuel Economy ◽  
Engine Performance ◽  
Control Unit ◽  
Calibration Method ◽  
Pollutant Emissions ◽  
Engine Control ◽  
Start Of Injection ◽  
Definition Of ◽  
Valid Solution

The calibration of the engine control unit is increased for the development of the whole automotive system. The aim is to calibrate the electronic engine control to match the decreasing emission requirements and increasing fuel economy demands. The reduction of the number of tests on vehicles represents one of the most important requirements for increasing efficiency of the engine calibration process. However, the definition of the design of experiment is not straightforward because the data is not known beforehand, so it is difficult to process and analyse this data to achieve a globally valid model. To reduce time effort and costs the virtual calibration can be a valid solution. This procedure is called software in the loop (SIL) calibration able to develop a process to systematically identify the optimal balance of engine performance, emissions and fuel economy. In this work, a virtual calibration methodology is presented by using a two-stage model to get minimum exhaust emissions of a diesel engine. The data used are from a GT-Power model of a 3L supercharged diesel engine. The model is able to calculate the engine emissions for different engine parameters (such as the start of injection, EGR fraction and rail pressure) and from optimisation process, new injection start maps that reduce pollutant emissions are created.

A CFD Study on Heavy Duty DI Diesel Engine to Achieve Ultra-Low Emissions

2010 ◽  
Author(s):  
M. Yilmaz ◽  
H. Koten ◽  
M. Zafer Gul
Keyword(s):  
Diesel Engine ◽  
Cfd Simulation ◽  
Combustion Engine ◽  
Direct Injection ◽  
Spray Angle ◽  
Combustion Model ◽  
Multiphase Model ◽  
Heavy Duty ◽  
Start Of Injection ◽  
Main Injection

Nowadays, automotive industries focused on clean diesel combustion in their combustion processes are investigated for their potential to achieve near zero particulate and NOx (Nitrogen oxides) emissions. Their main disadvantages are increased level of unburned hydrocarbons (HC) and carbon monoxide (CO) emissions, combustion control at high load, power output and limited operating range. The simulation of the air flow, spray and combustion in an internal combustion engine were prepared for a single cylinder of a nine-liter, six cylinder diesel engine. Many times the geometry is complex because moving pistons and valves are involved, which makes it difficult to generate structured mesh. In-cylinder spray-air motion interaction, a Lagrangian multiphase model has been applied in a heavy-duty CI engine under direct injection conditions. A comprehensive model for atomization of liquid sprays under high injection pressures has been employed. Three dimensional CFD calculations of the intake, compression and power strokes have been carried out with different spray angle, spray profile and start of injection. A new combustion model ECFM-3Z (Extended Coherent Flame Model) developed at IFP is used for combustion modeling. Finally, a calculation on an engine configuration with compression, spray injection and combustion in a direct injection Diesel engine is presented. In this study, exhaust emissions, and particularly the emission of NOx, CO and soot derived from premixed combustion are investigated, and the relationship between combustion and emission characteristics are showed. The calculated CFD simulation in different combustion cases was compared. The cases were prepared by changing the parameters: start of injection, spray angle and spray profile. Modeling of combustion proposed in the present study can be outlined as follows. NOx concentration is decreased by combustion of a over lean-mixture modeled by the pre-injection. Most of pre-mixture is combusted by main-injection, and therefore the amount of pre-injection and main-injection come into prominence. The results are greatly in agreement qualitatively with the previous experimental and computational studies in the literature.

Manifold Gas Dynamics Modeling and Its Coupling With Single-Cylinder Engine Models Using Simulink

2003 ◽  
Vol 125 (2) ◽  
pp. 563-571 ◽  
Author(s):  
G. Q. Zhang ◽  
D. N. Assanis
Keyword(s):  
Diesel Engine ◽  
Diesel Engines ◽  
Gas Dynamics ◽  
Combustion Engine ◽  
Coupled Model ◽  
Spark Ignition ◽  
Dynamics Modeling ◽  
Single Cylinder ◽  
Parametric Studies ◽  
Good Agreement

A flexible model for computing one-dimensional, unsteady manifold gas dynamics in single-cylinder spark-ignition and diesel engines has been developed. The numerical method applies an explicit, finite volume formulation and a shock-capturing total variation diminishing scheme. The numerical model has been validated against the method of characteristics for valve flows without combustion prior to coupling with combustion engine simulations. The coupling of the gas-dynamics model with single-cylinder, spark-ignition and diesel engine modules is accomplished using the graphical MATLAB-SIMULINK environment. Comparisons between predictions of the coupled model and measurements shows good agreement for both spark ignition and diesel engines. Parametric studies demonstrating the effect of varying the intake runner length on the volumetric efficiency of a diesel engine illustrate the model use.

The Need for Excellence

1989 ◽  
Vol 203 (1) ◽  
pp. 1-18
Author(s):  
C C J French
Keyword(s):  
Heat Transfer ◽  
Diesel Engine ◽  
Internal Combustion Engine ◽  
Diesel Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
World Market ◽  
The Future

The 1988 President gives a brief resume of his education and apprenticeship and then goes on to review his career at Ricardo Consulting Engineers. He describes some of the projects with which he has been involved, including a torpedo engine, a recycle diesel engine, heat transfer in engines, two-cycle diesel engines and the Atlas research engine. He discusses the future of the reciprocating internal combustion engine and concludes by emphasizing the need for engineering excellence in an increasingly competitive world market.

Performance and Emission of B100 Biodiesel with Various Additives in Direct Injection Diesel Engine

2021 ◽  
Vol 80 (1) ◽  
pp. 24-36
Author(s):  
Cheah Yi Linn ◽  
Mohd Radzi Abu Mansor ◽  
Zul Ilham
Keyword(s):  
Diesel Engine ◽  
Diesel Engines ◽  
Alternative Fuels ◽  
Combustion Engine ◽  
Direct Injection ◽  
Calorific Value ◽  
Diethyl Ester ◽  
Combustion Characteristic ◽  
Biodiesel Fuel ◽  
Performance And Emission

Alternative fuels for diesel engines have become highly important in the automotive industry due to the depleting fossil fuel sources and increased environmental concerns. Biodiesel fuel has a good combustion characteristic because of their long-chain hydrocarbon structure but the higher density and viscosity of the fuel can contribute to several engine problems such as low atomization, carbon deposit formation and injector clogging. The production of biodiesel with additives can help with the performance and emissions of diesel engines. There are many types of additives on the market but the extent of the additives on engine performance is unknown and lack of research has been done in studying the performance, emissions and fuel consumption together with B100 biodiesel. In this research, there are five types of B100 palm oil methyl ester biodiesel with various additive compositions need to be identified. The density, viscosity and calorific value of biodiesel samples were measured to study the thermo-physical properties as a simulation input. Simulation of the combustion engine is conducted using CONVERGE CFD software; based on single-cylinder, direct injection, YANMAR TF90 diesel engine parameters to study on the combustion characteristics and exhaust emissions. The simulation results were compared with the experiment results. From the simulations, biodiesel with diethyl ester and n-butanol additives give better results compared to other additives because the present of n-butanol PME is believed to reduce CO, CO2 and NOx emissions while diethyl ether can improve the spray characteristics when it blends with B100 biodiesel due to its low density and viscosity.

DEVELOPMENT OF THE COMBUSTION CHAMBER OF GAS ENGINE, CONVERTED ON THE BASIS OF DIESELS D-120 OR D-144 ENGINES TO WORK FOR ON LIQUEFIED PETROLEUM GAS

2019 ◽  
pp. 2-8
Author(s):  
Serhii Kovalov
Keyword(s):  
Combustion Chamber ◽  
Compression Ratio ◽  
Diesel Engines ◽  
Combustion Engine ◽  
Motor Fuel ◽  
Liquefied Petroleum Gas ◽  
Gas Engine ◽  
Chamber Volume ◽  
Motor Fuels ◽  
Dynamic Cycle

The expediency of using vehicles of liquefied petroleum gas as a motor fuel, as com-pared with traditional liquid motor fuels, in particular with diesel fuel, is shown. The advantages of converting diesel engines into gas ICEs with forced ignition with respect to conversion into gas diesel engines are substantiated. The analysis of methods for reducing the compression ratio in diesel engines when converting them into gas ICEs with forced ignition has been carried out. It is shown that for converting diesel engines into gas ICEs with forced ignition, it is advisable to use the Otto thermo-dynamic cycle with a decrease in the geometric degree of compression. The choice is grounded and an open combustion chamber in the form of an inverted axisymmetric “truncated cone” is developed. The proposed shape of the combustion chamber of a gas internal combustion engine for operation in the LPG reduces the geometric compression ratio of D-120 and D-144 diesel engines with an unseparated spherical combustion chamber, which reduces the geometric compression ratio from ε = 16,5 to ε = 9,4. The developed form of the combustion chamber allows the new diesel pistons or diesel pistons which are in operation to be in operation to be refined, instead of making special new gas pistons and to reduce the geometric compression ratio of diesel engines only by increasing the combustion chamber volume in the piston. This method of reducing the geometric degree of compression using conventional lathes is the most technologically advanced and cheap, as well as the least time consuming. Keywords: self-propelled chassis SSh-2540, wheeled tractors, diesel engines D-120 and D-144, gas engine with forced ignition, liquefied petroleum gas (LPG), compression ratio of the internal com-bustion engine, vehicles operating in the LPG.

scholarly journals Quality assessment of gas produced from different types of biomass pellets in gasification process

2019 ◽  
Vol 38 (2) ◽  
pp. 406-416 ◽  
Author(s):  
Marcel Mikeska ◽  
Jan Najser ◽  
Václav Peer ◽  
Jaroslav Frantík ◽  
Jan Kielar
Keyword(s):  
Gas Turbines ◽  
Combustion Engine ◽  
Calorific Value ◽  
Internal Combustion ◽  
Combustion Gas ◽  
Gas Cleaning ◽  
Gasification Process ◽  
Different Types ◽  
Before And After ◽  
Cleaning Technology

Gas from the gasification of pellets made from renewable sources of energy or from lower-quality fuels often contains a number of pollutants. This may cause technical difficulties during the gas use in internal combustion gas engines used for energy and heat cogeneration. Therefore, an adequate system of gas cleaning must be selected. In line with such requirements, this paper focuses on the characterization and comparison of gases produced from different types of biomass during gasification. The biomass tested was wood, straw, and hay pellets. The paper gives a detailed description and evaluation of the measurements from a fix-bed gasifier for the properties of the produced gases, raw fuels, tar composition, and its particle content before and after the cleaning process. The results of elemental composition, net calorific value, moisture, and ash content show that the cleaned gases are suitable for internal combustion engine-based cogeneration systems, but unsuitable for gas turbines, where a different cleaning technology would be needed.

scholarly journals An Economical and Precise Cooling Model and Its Application in a Single-Cylinder Diesel Engine

2021 ◽  
Vol 11 (15) ◽  
pp. 6749
Author(s):  
Zhifeng Xie ◽  
Ao Wang ◽  
Zhuoran Liu
Keyword(s):  
Diesel Engine ◽  
Cooling System ◽  
Combustion Engine ◽  
Electronic Control Unit ◽  
Total Power ◽  
Dynamical Characteristic ◽  
Water Jacket ◽  
Single Cylinder ◽  
Pump Speed ◽  
Total Power Consumption

The cooling system is an important subsystem of an internal combustion engine, which plays a vital role in the engine’s dynamical characteristic, the fuel economy, and emission output performance at each speed and load. This paper proposes an economical and precise model for an electric cooling system, including the modeling of engine heat rejection, water jacket temperature, and other parts of the cooling system. This model ensures that the engine operates precisely at the designated temperature and the total power consumption of the cooling system takes the minimum value at some power proportion of fan and pump. Speed maps for the cooling fan and pump at different speeds and loads of engine are predicted, which can be stored in the electronic control unit (ECU). This model was validated on a single-cylinder diesel engine, called the DK32. Furthermore, it was used to tune the temperature of the water jacket precisely. The results show that in the common use case, the electric cooling system can save the power of 255 W in contrast with the mechanical cooling system, which is about 1.9% of the engine’s power output. In addition, the validation results of the DK32 engine meet the non-road mobile machinery China-IV emission standards.

Sign in / Sign up

Export Citation Format

Share Document