scholarly journals The use of ceramics as an internal curing agent in high performance concrete with variable temperature curing to improve mechanical characteristics

2022 ◽  
Vol 961 (1) ◽  
pp. 012024
Author(s):  
Abdulrasool Thamer Abdulrasool ◽  
Noor R. Kadhim ◽  
Safaa S. Mohammed ◽  
Ahmed Abdulmueen Alher
Keyword(s):  
Compressive Strength ◽  
High Performance ◽  
Mechanical Characteristics ◽  
High Performance Concrete ◽  
Variable Temperature ◽  
Porous Ceramic ◽  
Autogenous Shrinkage ◽  
Internal Curing ◽  
Fine Aggregate ◽  
Fine Aggregates

Abstract Concrete curing is one of the most significant factors in the development of compressive strength, and a high temperature difference during curing may reduce strength. The microcracks created in the concrete as a result of the constant temperature change cause this exudation. Internal curing has become popular for decreasing the risk of early-age cracking in high-performance concrete by limiting autogenous shrinkage (HPC). This study looks at the effectiveness of internal wet curing offered by a new kind of aggregate called “recycled waste porous ceramic fine aggregates”. The evolution of measured mechanical characteristics is examined on three distinct HPCs, both with and without internal curing materials. Ceramic fine aggregates were used to replace two different quantities of regular weight fine aggregate. Ceramic fine aggregates were shown to be quite beneficial for internal cure. It has been discovered that incorporating 20% ceramic fine aggregates into HPC improves the properties of the material, resulting in low internal stress and a large improvement in compressive strength. It should be emphasized that, unlike some traditional lightweight aggregates, no loss in compressive strength has been seen for the various quantities of ceramic fine aggregates introduced at either early or later ages.

scholarly journals Effect Of Attapulgite as Internal Curing in High-Performance Concrete with Variable Temperature Curing to Enhance Mechanical Properties

2022 ◽  
Vol 961 (1) ◽  
pp. 012054
Author(s):  
Abdulrasool Thamer Abdulrasool ◽  
Safaa S. Mohammed ◽  
Noor R. Kadhim ◽  
Yasir N. Kadhim
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
High Performance ◽  
High Performance Concrete ◽  
Variable Temperature ◽  
Normal Weight ◽  
Internal Curing ◽  
Large Temperature ◽  
Fine Aggregate ◽  
Fine Aggregates

Abstract One of the most important elements in the development of compressive strength is concrete curing, and a large temperature differential during curing may decrease strength. This exudation is caused by microcracks in the concrete caused by the continuous temperature fluctuation. By minimizing autogenous shrinkage, internal curing has become popular for reducing the danger of early-age cracking in high-performance concrete (HPC). The efficacy of internal wet curing provided by fine Attapulgite aggregate is investigated in this research. On three different HPCs, both with and without internal curing materials, the development of observed mechanical properties is investigated. Two different amounts of normal weight fine aggregate were replaced with attapulgite fine aggregates. Internal cure has been found to benefit from attapulgite fine aggregates. It has been found that adding 20% Attapulgite fine aggregates to HPC enhances the material’s characteristics, resulting in low internal stress and a significant increase in compressive strength. It should be noted that, unlike certain conventional lightweight aggregates, the different amounts of Attapulgite fine aggregates added at various ages have shown no decrease in compressive strength.

scholarly journals Effect of Mineral Aggregates and Chemical Admixtures as Internal Curing Agents on the Mechanical Properties and Durability of High-Performance Concrete

Materials ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2090 ◽  
Author(s):  
Francisco Javier Vázquez-Rodríguez ◽  
Nora Elizondo-Villareal ◽  
Luz Hypatia Verástegui ◽  
Ana Maria Arato Tovar ◽  
Jesus Fernando López-Perales ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
High Performance ◽  
High Performance Concrete ◽  
Chloride Ions ◽  
Internal Curing ◽  
Fine Aggregate ◽  
Pumice Stone ◽  
Chemical Admixtures ◽  
Mineral Aggregates

In the present work, the effect of mineral aggregates (pumice stone and expanded clay aggregates) and chemical admixtures (superplasticizers and shrinkage reducing additives) as an alternative internal curing technique was investigated, to improve the properties of high-performance concrete. In the fresh and hardened state, concretes with partial replacements of Portland cement (CPC30R and OPC40C) by pulverized fly ash in combination with the addition of mineral aggregates and chemical admixtures were studied. The physical, mechanical, and durability properties in terms of slump, density, porosity, compressive strength, and permeability to chloride ions were respectively determined. The microstructural analysis was carried out by scanning electronic microscopy. The results highlight the effect of the addition of expanded clay aggregate on the internal curing of the concrete, which allowed developing the maximum compressive strength at 28 days (61 MPa). Meanwhile, the replacement of fine aggregate by 20% of pumice stone allowed developing the maximum compressive strength (52 MPa) in an OPC-based concrete at 180 days. The effectiveness of internal curing to develop higher strength is attributed to control in the porosity and a high water release at a later age. Finally, the lowest permeability value at 90 days (945 C) was found by the substitutions of fine aggregate by 20% of pumice stone saturated with shrinkage reducing admixture into pores and OPC40C by 15% of pulverized fly ash. It might be due to impeded diffusion of chloride ions into cement paste in the vicinity of pulverized fly ash, where the pozzolanic reaction has occurred. The proposed internal curing technology can be considered a real alternative to achieve the expected performance of a high-performance concrete since a concrete with a compressive strength range from 45 to 67 MPa, density range from 2130 to 2310 kg/m3, and exceptional durability (< 2000 C) was effectively developed.

Effect of Copper Slag as a Fine Aggregate on the Durability Characteristics of High-Performance Concrete (HPC) Containing Silica Fume

2020 ◽  
Vol 07 (02) ◽  
pp. 1-10
Author(s):  
Rizwan Ahmad Khan ◽  
Keyword(s):  
Silica Fume ◽  
High Performance ◽  
High Performance Concrete ◽  
Copper Slag ◽  
Chloride Penetration ◽  
Interfacial Transition Zone ◽  
Fine Aggregate ◽  
Fresh Properties ◽  
Fine Aggregates ◽  
Effect Of Copper

This paper investigates the fresh and durability properties of the high-performance concrete by replacing cement with 15% Silica fume and simultaneously replacing fine aggregates with 25%, 50%, 75% and 100% copper slag at w/b ratio of 0.23. Five mixes were analysed and compared with the standard concrete mix. Fresh properties show an increase in the slump with the increase in the quantity of copper slag to the mix. Sorptivity, chloride penetration, UPV and carbonation results were very encouraging at 50% copper slag replacement levels. Microstructure analysis of these mixes shows the emergence of C-S-H gel for nearly all mixes indicating densification of the interfacial transition zone of the concrete.

Mechanical Properties and Durability of Ultra-High Performance Concrete Incorporating Coarse Aggregate

2014 ◽  
Vol 629-630 ◽  
pp. 96-103 ◽  
Author(s):  
Juan Yang ◽  
Gai Fei Peng ◽  
Yu Xin Gao ◽  
Hui Zhang
Keyword(s):  
Compressive Strength ◽  
High Performance ◽  
Coarse Aggregate ◽  
High Performance Concrete ◽  
Fresh Concrete ◽  
Raw Materials ◽  
Autogenous Shrinkage ◽  
Mineral Admixtures ◽  
Ultra High Performance Concrete ◽  
Spalling Failure

Ultra-high performance concrete (UHPC) incorporating coarse aggregate was prepared with common raw materials. Fresh concrete had excellent good workability with slump of 265 mm and slump spread of 673 mm. Compressive strength of UHPC at 56 d reached 150 MPa. However, UHPC exhibited high brittleness in terms of spalling failure which occurred during compression loading.The ratio of splitting tensile strength to compressive strength of about 1/18 and the ratio of flexural strength to compressive strength of about 1/14 at 56 d were also associated with the brittleness of UHPC in this research. Mineral admixtures and fluidity of fresh concrete influenced compressive strength of UHPC significantly. Moreover, UHPC had excellent permeation-related durability but considerable shrinkage. Autogenous shrinkage of UHPC was less than half of free shrinkage, for which the reason is unknown and needs further research.

scholarly journals Mechanical Performance and Microstructure of Ultra-High-Performance Concrete Modified by Calcium Sulfoaluminate Cement

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Meimei Song ◽  
Chuanlin Wang ◽  
Ying Cui ◽  
Qiu Li ◽  
Zhiyang Gao
Keyword(s):  
Compressive Strength ◽  
High Performance ◽  
Mechanical Performance ◽  
High Performance Concrete ◽  
Autogenous Shrinkage ◽  
Ultra High Performance Concrete ◽  
Maximum Heat ◽  
Degree Of Hydration ◽  
Calcium Sulfoaluminate ◽  
Shrinkage Property

High autogenous shrinkage property is one of the disadvantages of ultra-high-performance concrete (UHPC), which may induce early age cracking and threaten the safety of concrete structure. In the present study, different dosages of calcium sulfoaluminate (CSA) cement were added in UHPC as an effective expansive binder. Hydration mechanism, autogenous shrinkage property, and compressive strength of UHPC were carried out to investigate the effect of CSA addition on the mechanical properties of UHPC. Scanning electron microscopy was also employed to characterize the intrinsic microstructural reasons relating to the changes in macroproperties. Based on the XRD diagram, increasing formation of ettringite and Ca(OH)2 can be found with increasing CSA content up to 15%. In the heat flow results of UHPC with 10% CSA addition, the maximum heat release increases to 2.6 mW/g, which is 8.3% higher than the reference UHPC, suggesting a higher degree of hydration with CSA addition. The results in autogenous shrinkage show that CSA expansion agent plays a significantly beneficial role in improving the autogenous shrinkage of UHPC. The corresponding autogenous shrinkage of UHPC is −59.66 μ ε , −131.11 μ ε , and −182.31 μ ε , respectively, at 7 d with 5%, 10%, and 15% addition, which is 108%, 117%, and 123% reduction compared to the reference specimen without CSA. In terms of compressive strength, UHPC with 5%, 10%, 15%, and 20% CSA addition has 10.5%, 17.4%, 30.2%, and 22.1% higher compressive strength than that for the reference UHPC at 28 d. Microstructural study shows that there is an extremely dense microstructure in both the bulk matrix and interfacial transition zone of UHPC with 10% CSA addition, which can be attributed to the higher autogenous shrinkage property and can therefore result in higher mechanical performance.

Mechanical Properties of High Performance Concrete Subjected to High Temperature as a Function of Fly-Ash and Fiber Addition

2014 ◽  
Vol 912-914 ◽  
pp. 227-230 ◽  
Author(s):  
Seung Jo Lee
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Weight Reduction ◽  
High Performance ◽  
Mechanical Characteristics ◽  
High Performance Concrete ◽  
Reduction Ratio ◽  
Crack Control ◽  
Residual Compressive Strength ◽  
Heating Up

The purpose of this study is to have a better understanding of the mechanical characteristics of high performance concrete which is produced by mixing reinforcing fiber controlled by high temperatures with fly ash. After heating up the concrete, its appearance, demolition mode, residual compressive strength, weight reduction ratio and other mechanical characteristics were measured. To improve the mechanical characteristics of concrete, it was mixed with nylon, polypropylene, steel fiber and fly ash. The specimen was exposed to 100 ~ 800°C and its crack control, spalling prevention and other mechanical characteristics were reviewed. When the high performance concrete was exposed to 600°C or higher, its residual compressive strength dropped but its weight reduction ratio was significantly higher than it was heated before.

Effect of Partial Substitution of Fine Aggregate with Copper Slag on Mechanical and Durability of High Performance Concrete-A Review

2020 ◽  
Vol 07 (01) ◽  
pp. 1-11
Author(s):  
Rizwan Ahmad Khan ◽  
Keyword(s):  
Construction Industry ◽  
High Performance ◽  
High Performance Concrete ◽  
Construction Materials ◽  
Copper Slag ◽  
Partial Substitution ◽  
Fine Aggregate ◽  
Natural Sand ◽  
Severe Problem ◽  
Fine Aggregates

The challenge before the construction industry is to meet the demand of the efficient and economically viable construction materials posed by the huge infrastructural needs. Many nations are observing an expeditious growth in the field of construction necessitating the utilization of natural reserves for the expansion of infrastructure. This expansion is giving a warning to available reserves of nature. The natural ingredients, fine aggregates and coarse aggregate constitute more than 70% volume of the concrete. The availability of these resources is decreasing at a very high pace. In fact due to the severe problem with the availability of natural sand, the construction industry is faced with the pressing need to consider available options to lessen the reliance on natural aggregates. Copper slag being a waste material, can be used as an option for fine aggregates. The substitution of fine aggregate from nature with waste materials from industries such as copper slag offers economic and technical dominance, which are of pronounced significance in the present scenario. This study is, based on the critical review of the development of High Performance Concrete (HPC) by replacing fine aggregate with copper slag by observing various other researches and reviews. The key intent of this paper is to closely look at the copper slag utility as an unconventional material to be used as a substitute of fine aggregate and its effect on mechanical and durability parameters of HPC.

scholarly journals Non-Tuned Machine Learning Approach for Predicting the Compressive Strength of High-Performance Concrete

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1023
Author(s):  
Abobakr Khalil Al-Shamiri ◽  
Tian-Feng Yuan ◽  
Joong Hoon Kim
Keyword(s):  
Machine Learning ◽  
Compressive Strength ◽  
Prediction Model ◽  
Extreme Learning Machine ◽  
High Performance ◽  
High Performance Concrete ◽  
Fine Aggregate ◽  
Input Variables ◽  
Prediction Reliability ◽  
Learning Machine

Compressive strength is considered as one of the most important parameters in concrete design. Time and cost can be reduced if the compressive strength of concrete is accurately estimated. In this paper, a new prediction model for compressive strength of high-performance concrete (HPC) was developed using a non-tuned machine learning technique, namely, a regularized extreme learning machine (RELM). The RELM prediction model was developed using a comprehensive dataset obtained from previously published studies. The input variables of the model include cement, blast furnace slag, fly ash, water, superplasticizer, coarse aggregate, fine aggregate, and age of specimens. k-fold cross-validation was used to assess the prediction reliability of the developed RELM model. The prediction results of the RELM model were evaluated using various error measures and compared with that of the standard extreme learning machine (ELM) and other methods presented in the literature. The findings of this research indicate that the compressive strength of HPC can be accurately estimated using the proposed RELM model.

Sign in / Sign up

Export Citation Format

Share Document