scholarly journals Delamination analysis of multilayered viscoelastic beam exposed to chemical degradation

2021 ◽  
Vol 1141 (1) ◽  
pp. 012017
Author(s):  
V Rizov
Keyword(s):  
Chemical Degradation ◽  
Viscoelastic Beam

A generic fluticasone propionate and salmeterol dry powder inhaler: Evidence of usability, function, and robustness

2021 ◽  
Vol 42 (1) ◽  
pp. 30-35 ◽  
Author(s):  
Donald P. Tashkin ◽  
Arkady Koltun ◽  
Róisín Wallace
Keyword(s):  
Chronic Obstructive Pulmonary Disease ◽  
Fluticasone Propionate ◽  
Healthy Volunteers ◽  
Pulmonary Disease ◽  
Dry Powder Inhaler ◽  
Chemical Degradation ◽  
Chronic Obstructive ◽  
Dry Powder ◽  
Obstructive Pulmonary Disease ◽  
Flow Rates

Background: A generic combination of fluticasone propionate and salmeterol xinafoate inhalation powder in a premetered, multidose, nonreusable inhaler was recently approved. Objective: To assess the performance of the generic device. Methods: Findings from three studies with regard to device usability, function, and robustness were reviewed. Results: In a study to assess device function in patients and healthy volunteers, the generic device was successfully used by patients with asthma and chronic obstructive pulmonary disease who were either dry powder inhaler users or dry powder inhaler‐naive, even though they were not trained beyond being provided the instructions for use. In a study to measure inhaled flow rates generated by patients and healthy volunteers, the generic device consistently simulated the delivery of a full dose of drug, even to patients with severe respiratory disease and reduced inspiratory flow rates. Although the generic device had a slightly higher airflow resistance, this study demonstrated that this difference did not result in any clinically meaningful differences in terms of drug delivery. Pressure drop, a key parameter that drives the fluidization and aerosolization of the powder dose, was found to be comparable between the devices. In an open-label study, the generic device met all U.S. Food and Drug Administration specifications for device robustness after 21.5 days of twice-daily dosing via oral inhalation among 111 participants with asthma or chronic obstructive pulmonary disease. All inhalers tested demonstrated conformity with a pharmacopeia with respect to key quality parameters (assay, delivered dose uniformity, aerodynamic size distribution). There was no evidence of chemical degradation of the active ingredients, nor of microbial or water ingress into the powder, as a result of inhaler use.

Mechanism of Perfluorsulfonic Acid Membrane Chemical Degradation Under Low RH Conditions

2013 ◽  
Vol 50 (2) ◽  
pp. 907-918 ◽  
Author(s):  
F. D. Coms ◽  
H. Xu ◽  
T. McCallum ◽  
C. Mittelsteadt
Keyword(s):  
Chemical Degradation

Preparation and characterisation of liquid epoxidised natural rubber in latex stage by chemical degradation

2021 ◽  
Author(s):  
Nurul Hayati Yusof ◽  
Dazylah Darji ◽  
Fatimah Rubaizah Mohd Rasdi ◽  
Krishna Veni Baratha Nesan
Keyword(s):  
Natural Rubber ◽  
Chemical Degradation

Enhanced Skin Permeation of Punicalagin after Topical Application of Pluronic Micelles or Vesicles Loaded with Lafoensia pacari Extract

Planta Medica ◽  
2021 ◽  
Author(s):  
Sandra Alves de Sousa Garcia ◽  
Priscila Bianca Rodrigues da Rocha ◽  
Bruno dos Santos Souza ◽  
Andressa Tuane Santana Paz ◽  
Ana Luiza Caetano Negris ◽  
...  
Keyword(s):  
Antioxidant Activity ◽  
Skin Permeation ◽  
Sol Gel ◽  
Extraction Procedure ◽  
Average Diameter ◽  
Skin Aging ◽  
Chemical Degradation ◽  
Vertical Diffusion ◽  
Flowing Liquid ◽  
Span 80

AbstractPunicalagin, the principal ellagitannin of Lafoensia pacari leaves, has proven antioxidant activity, and standardized extracts of L. pacari can be topically used for skin aging management. We hypothesized that Pluronic nanomicelles or vesicles could solubilize sufficiently large amounts of the standardized extracts of L. pacari and provide chemical stability to punicalagin. The standardized extracts of L. pacari were obtained with an optimized extraction procedure, and the antioxidant activity was characterized. Formulations containing Pluronic at 25% and 35% were obtained with or without Span 80. They were characterized by average diameter, polydispersity index, punicalagin content, physicochemical stability, and rheology. A release and skin permeation study was carried out in vertical diffusion cells. The extraction procedure allowed quantifying high punicalagin content (i.e., 141.61 ± 3.87 mg/g). The standardized extracts of L. pacari showed antioxidant activity for all evaluated methods. Pluronic at 25 and Pluronic at 35 with standardized extracts of L. pacari showed an average diameter of about 25 nm. The addition of Span 80 significantly increased the mean diameter by 15-fold (p < 0.05), indicating the spontaneous formation of vesicles. Pluronic formulations significantly protected punicalagin from chemical degradation (p < 0.05). Pluronic at 25 formulations presented as free-flowing liquid-like systems, while Pluronic at 35 resulted in an increase of about 44-fold in |ƞ*|. The addition of Span 80 significantly reduced the Pluronic sol-gel transition temperature (p < 0.05), indicating the formation of vesicles. Formulations with Span 80 significantly enhanced punicalagin skin permeation compared to formulations without Span 80 (p < 0.05). Formulations with Span 80 were demonstrated to be the most promising formulations, as they allowed significant permeation of punicalagin (about 80 to 315 µg/cm2), which has been shown to have antioxidant activity.

scholarly journals Influence of artificial aging: mechanical and physicochemical properties of dental composites under static and dynamic compression

2021 ◽  
Author(s):  
D. C. Gornig ◽  
R. Maletz ◽  
P. Ottl ◽  
M. Warkentin
Keyword(s):  
Mechanical Properties ◽  
Water Sorption ◽  
Artificial Aging ◽  
Filler Content ◽  
Dynamic Compression ◽  
The Other ◽  
Chemical Degradation ◽  
Dental Composites ◽  
Compression Tests ◽  
Acid Ph

Abstract Objective The aim of the study was to evaluate the influence of filler content, degradation media and time on the mechanical properties of different dental composites after in vitro aging. Materials and Methods Specimens (1 mm3) of three commercially available composites (GrandioSO®, Arabesk Top®, Arabesk Flow®) with respect to their filler content were stored in artificial aging media: artificial saliva, ethanol (60%), lactic acid (pH 5) and citric acid (pH 5). Parameters (Vickers microhardness, compressive strength, elastic modulus, water sorption and solubility) were determined in their initial state (control group, n = 3 for microhardness, n = 5 for the other parameters) and after 14, 30, 90 and 180 days (n = 3 for microhardness, n = 5 for the other parameters for each composite group, time point and media). Specimens were also characterized with dynamic-mechanical-thermal analysis (compression tests, F =  ± 7 N; f = 0.5 Hz, 1 Hz and 3.3 Hz; t = 0–170 °C). Results Incorporation of fillers with more than 80 w% leads to significantly better mechanical properties under static and dynamic compression tests and a better water sorption behavior, even after chemical degradation. The influence of degradation media and time is of subordinate importance for chemical degradation. Conclusion Although the investigated composites have a similar matrix, they showed different degradation behavior. Since dentine and enamel occur only in small layer thickness, a test specimen geometry with very small dimensions is recommended for direct comparison. Moreover, the use of compression tests to determine the mechanical parameters for the development of structure-compatible and functionally adapted composites makes sense as an additional standard. Clinical relevance Preferential use of highly filled composites for occlusal fillings is recommended.

scholarly journals In-Situ Synthesis of TiO2@GO Nanosheets for Polymers Degradation in a Natural Environment

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2158
Author(s):  
Yueqin Shi ◽  
Zhanyang Yu ◽  
Zhengjun Li ◽  
Xiaodong Zhao ◽  
Yongjun Yuan
Keyword(s):  
Natural Environment ◽  
New Technologies ◽  
Separation Efficiency ◽  
Basic Mechanism ◽  
Chemical Degradation ◽  
Natural Environments ◽  
Additional Energy ◽  
Photogenerated Electrons ◽  
Main Components

Plastic photodegradation naturally takes 300–500 years, and their chemical degradation typically needs additional energy or causes secondary pollution. The main components of global plastic are polymers. Hence, new technologies are urgently required for the effective decomposition of the polymers in natural environments, which lays the foundation for this study on future plastic degradation. This study synthesizes the in-situ growth of TiO2 at graphene oxide (GO) matrix to form the TiO2@GO photocatalyst, and studies its application in conjugated polymers’ photodegradation. The photodegradation process could be probed by UV-vis absorption originating from the conjugated backbone of polymers. We have found that the complete decomposition of various polymers in a natural environment by employing the photocatalyst TiO2@GO within 12 days. It is obvious that the TiO2@GO shows a higher photocatalyst activity than the TiO2, due to the higher crystallinity morphology and smaller size of TiO2, and the faster transmission of photogenerated electrons from TiO2 to GO. The stronger fluorescence (FL) intensity of TiO2@GO compared to TiO2 at the terephthalic acid aqueous solution indicates that more hydroxyl radicals (•OH) are produced for TiO2@GO. This further confirms that the GO could effectively decrease the generation of recombination centers, enhance the separation efficiency of photoinduced electrons and holes, and increase the photocatalytic activity of TiO2@GO. This work establishes the underlying basic mechanism of polymers photodegradation, which might open new avenues for simultaneously addressing the white pollution crisis in a natural environment.

scholarly journals Comparative chemical investigations of alum treated archaeological wood from various museum collections

2021 ◽  
Vol 9 (1) ◽  
Author(s):  
Jeannette Jacqueline Łucejko ◽  
Caitlin M. A. McQueen ◽  
Malin Sahlstedt ◽  
Francesca Modugno ◽  
Maria Perla Colombini ◽  
...  
Keyword(s):  
Cultural History ◽  
Inorganic Compounds ◽  
Treated Wood ◽  
Chemical Degradation ◽  
General Level ◽  
History Museum ◽  
X Ray ◽  
Archaeological Wood ◽  
Alum Treatment ◽  
Swedish History

AbstractFrom the mid-1800s to the late 1960s, conservation by alum salts (KAl(SO4)2·12H2O—potassium aluminium sulphate), using various recipes, was a common method to prevent shrinkage and to strengthen waterlogged archaeological wooden objects. This method was mainly used in Scandinavia. The alum method appears to have also been applied to highly degraded archaeological waterlogged wood in other countries, for example in the U.S and Germany. Today, many of the archaeological wooden objects treated with alum show extreme deterioration and very low pH, which are attributed to the effects of the alum-treatment. This study investigated the extent of the current levels of chemical degradation in wooden objects conserved with alum salts at different points in time (1880s, 1930s and 1905–13) in order to understand their current condition and whether extent of degradation was in any way related to time of treatment, in an attempt to understand the rate of degradation. It was also an opportunity to compare the chemical state of preservation of alum-treated wood from different collections, as only the Oseberg collection has been intensively studied in this way up until now. Samples from historical wooden objects from the following collections were investigated and compared: the Dejbjerg collection (National Museum of Denmark in Copenhagen); the Oseberg collection (Museum of Cultural History, Oslo, Norway); the Glimmingehus collection (Swedish History Museum, Sweden). Analyses of lignocellulosic polymers and of inorganic compounds were undertaken to evaluate the chemical preservation of the wooden objects. The investigations were performed using a multi-analytical approach which consisted of: pH measurements, analytical pyrolysis (Py-GC/MS), X-ray diffraction (XRD) and scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM–EDS). It was possible to link the extent of degradation with time, on a general level but we found a great variability in the state of preservation of the wood also within the same collection. It is clear, however that alum-treated wood is more degraded than archaeological wood not treated with alum.

Sign in / Sign up

Export Citation Format

Share Document