scholarly journals Effect of 45S5 bioactive glass on the sintering temperature of titanium-hydroxyapatite composite

2021 ◽  
Vol 1192 (1) ◽  
pp. 012021
Author(s):  
D S Abu Bakar ◽  
M G Kutty ◽  
N A Yahya
Keyword(s):  
Mechanical Properties ◽  
Bioactive Glass ◽  
Sintering Temperature ◽  
Physical And Mechanical Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Volumetric Expansion ◽  
Fourier Transformed Infrared Spectroscopy ◽  
Lower Temperature ◽  
Mechanical Properties And Corrosion

Abstract Titanium (Ti) is widely known for its good mechanical properties and corrosion resistance. However, it has poor biocompatibility. Hydroxyapatite (HA) is a biocompatible material but has poor mechanical properties. Making Ti-HA composite creates a promising choice of biomaterial in dental and medical applications. However, creating a Ti-HA composite requires sintering at high temperatures which leads to oxidation of Ti. The aim of this study was to reduce the sintering temperature of Ti-HA composite by incorporating 45S5 Bioactive Glass (BG) without compromising the chemical, physical and mechanical properties of the composite. In this study, a Ti-HA-BG composite with wt% of 45-45-10 respectively was produced via powder metallurgy. This was compared with the control composite consisting of 50 wt% Ti- 50 wt% HA. Powders according to the above-mentioned ratio were milled at 200 rpm for 5 hours by using a planetary ball milling machine. Samples were then compacted into cylindrical pellets via uniaxial pressing at 1500 psi and sintered in an atmospheric furnace at 1000 °C, 1100 °C and 1200 °C for 4 hours. Ti-HA and Ti-HA-BG sample characteristics were examined and compared by using Fourier Transformed Infrared Spectroscopy (FTIR), Energy Dispersive X-Ray (EDX) and X-Ray Diffraction (XRD). The density and volumetric expansion of the composites were also measured and compared. Results from XRD data indicate the reduction of oxidation of Ti and decomposition of HA in Ti-HA-BG composite at lower temperature in comparison to Ti-HA composite. The density of Ti-HA-BG composites are higher compared to Ti-HA composite while the volumetric expansion of Ti-HA-BG composites is lesser than Ti-HA composite. Therefore, BG is a low melting point additive that acts as a good sintering aid to effectively lower the sintering temperature while maintaining the desired properties of initial components.

Effects of the Sintering Temperature on Structural and Bioactivity in BaFe12O19-P2O5-CaO-Na2O Bioactive Glass Ceramic

2015 ◽  
Vol 804 ◽  
pp. 147-150
Author(s):  
Pratthana Intawin ◽  
Kamonpan Pengpat ◽  
Wilaiwan Leenakul ◽  
Tawee Tunkasiri
Keyword(s):  
Mechanical Properties ◽  
Bioactive Glass ◽  
Glass Ceramic ◽  
Sintering Temperature ◽  
Glass Ceramics ◽  
Microstructural Properties ◽  
Hardness Testing ◽  
X Ray Diffraction ◽  
X Ray

In this research, the effects of sintering temperatures on structural and bioactivity in BaFe12O19 (BF) /P2O5-CaO-Na2O bioactive glass ceramics were investigated. The BF/P2O5-CaO-Na2O bioactive glass ceramics were fabricated under various sintering temperatures in a range of 550-700 oC. X-ray diffraction (XRD) technique and the scanning electron microscopy (SEM) are used to characterize phase and microstructure. The studied samples were evaluated for mechanical properties by hardness testing. Moreover, the bioactivities of studied samples were studied by using simulated body fluid (SBF) in vitro. It was found that, the sintering temperatures are the most influential parameter on microstructure and mechanical properties of the bioactive glass ceramics. The highest density of studied ceramics was found in the sample sintered at 700 oC. The microstructural properties of the studies samples were investigated and the results were then correlated with the characteristics of sintering temperature as well as the microstructure of the bioactive glass ceramic. Moreover, the covering of bone-like apatite layer on the surface sample after a 7 day immersion in SBF suggested that the BF/P2O5-CaO-Na2O glass ceramics have acceptable bioactivities.

Comparison of Mechanical Properties of Sheep Hydroxyapatite (SHA) and Commercial Synthetic Hydroxyapatite (CSHA)-MgO Composites

2011 ◽  
Vol 493-494 ◽  
pp. 588-593 ◽  
Author(s):  
N. Demirkol ◽  
Onur Meydanoglu ◽  
Hasan Gökçe ◽  
F.N. Oktar ◽  
E.S. Kayali
Keyword(s):  
Mechanical Properties ◽  
Compression Strength ◽  
Vickers Microhardness ◽  
Sintering Temperature ◽  
Physical And Mechanical Properties ◽  
X Ray Diffraction ◽  
Time Saving ◽  
X Ray ◽  
Density Values ◽  
Synthetic Hydroxyapatite

In this study, microstructures and mechanical properties of sheep hydroxyapatite (SHA) and commercial synthetic hydroxyapatite (CSHA)-MgO composites were investigated. The production of hydroxyapatite (HA) from natural sources is preferred due to economical and time saving reasons. The goal of development of SHA and CSHA based MgO composites is to improve mechanical properties of HA. SHA and CSHA composites were prepared with the addition of different amounts of MgO and sintered at the temperature range of 1000-1300 °C. The physical and mechanical properties were determined by measuring density, compression strength and Vickers microhardness (HV). Structural characterization was carried out with X-ray diffraction (XRD) and scanning electron microscopy (SEM) studies. In all composites, mean density values and mechanical properties increased with increasing sintering temperature. The increase of MgO content in SHA-MgO composites showed better mechanical properties in contrast to CSHA-MgO composites. Although the highest hardness and compression strength values were obtained at the SHA-10wt% MgO composite sintered at 1300°C, higher hardness and compression strength values were achieved with 5 wt% MgO addition at the CSHA-MgO composites when compared to SHA-MgO composites sintered between 1000-1200°C.

scholarly journals Transport and Dielectric Properties of Mechanosynthesized La2/3Cu3Ti4O12 Ceramics

Crystals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 313
Author(s):  
Mohamad M. Ahmad ◽  
Hicham Mahfoz Kotb ◽  
Celin Joseph ◽  
Shalendra Kumar ◽  
Adil Alshoaibi
Keyword(s):  
Dielectric Constant ◽  
Sintering Temperature ◽  
Cubic Phase ◽  
X Ray Diffraction ◽  
Boundary Conductivity ◽  
X Ray ◽  
Giant Dielectric ◽  
Mechanochemical Milling ◽  
Giant Dielectric Constant ◽  
Lower Temperature

La2/3Cu3Ti4O12 (LCTO) powder has been synthesized by the mechanochemical milling technique. The pelletized powder was conventionally sintered for 10 h at a temperature range of 975–1025 °C, which is a lower temperature process compared to the standard solid-state reaction. X-ray diffraction analysis revealed a cubic phase for the current LCTO ceramics. The grain size of the sintered ceramics was found to increase from 1.5 ± 0.5 to 2.3 ± 0.5 μm with an increase in sintering temperature from 975 to 1025 °C. The impedance results show that the grain conductivity is more than three orders of magnitude larger than the grain boundary conductivity for LCTO ceramics. All the samples showed a giant dielectric constant (1.7 × 103–3.4 × 103) and dielectric loss (0.09–0.17) at 300 K and 10 kHz. The giant dielectric constant of the current samples was attributed to the effect of internal barrier layer capacitances due to their electrically inhomogeneous structure.

scholarly journals Effects of Sintering Temperature on Densification, Microstructure and Mechanical Properties of Al-Based Alloy by High-Velocity Compaction

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 218
Author(s):  
Xianjie Yuan ◽  
Xuanhui Qu ◽  
Haiqing Yin ◽  
Zaiqiang Feng ◽  
Mingqi Tang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Velocity ◽  
Sintered Density ◽  
Sintering Temperature ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
High Velocity Compaction ◽  
Sintered Temperature

This present work investigates the effects of sintering temperature on densification, mechanical properties and microstructure of Al-based alloy pressed by high-velocity compaction. The green samples were heated under the flow of high pure (99.99 wt%) N2. The heating rate was 4 °C/min before 315 °C. For reducing the residual stress, the samples were isothermally held for one h. Then, the specimens were respectively heated at the rate of 10 °C/min to the temperature between 540 °C and 700 °C, held for one h, and then furnace-cooled to the room temperature. Results indicate that when the sintered temperature was 640 °C, both the sintered density and mechanical properties was optimum. Differential Scanning Calorimetry, X-ray diffraction of sintered samples, Scanning Electron Microscopy, Energy Dispersive Spectroscopy, and Transmission Electron Microscope were used to analyse the microstructure and phases.

Physical and Mechanical Properties of Cement Paste Were Used Partially with Fly Ash and Kaolin Waste

2017 ◽  
Vol 866 ◽  
pp. 199-203
Author(s):  
Chidchanok Chainej ◽  
Suparut Narksitipan ◽  
Nittaya Jaitanong
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Room Temperature ◽  
Physical And Mechanical Properties ◽  
Partial Replacement ◽  
X Ray Diffraction ◽  
X Ray ◽  
Lime Water ◽  
Diffraction Patterns ◽  
Iron Mold

The aims of this research were study the microstructures and mechanical properties for partial replacement of cement with Fly ash (FA) and kaolin waste (KW). Ordinary Portland cement were partially replaced with FA and KW in the range of 25-35% and 10-25% by weight of cement powder. The kaolin waste was ground for 180 minutes before using. The specimen was packing into an iron mold which sample size of 5×5×5 cm3. Then, the specimens were kept at room temperature for 24 hours and were moist cured in the incubation lime water bath at age of 3 days. After that the specimens were dry cured with plastic wrap at age of 3, 7, 14 and 28 days. After that the compounds were examined by x-ray diffraction patterns (XRD) and the microstructures were examined by scanning electron microscopy (SEM). The compressive strength was then investigated.

scholarly journals Features of the hydration process of the modified blended cement for fiber cement panels

2018 ◽  
Vol 170 ◽  
pp. 03030 ◽  
Author(s):  
Rustem Mukhametrakhimov ◽  
Liliya Lukmanova
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Blended Cement ◽  
Physical And Mechanical Properties ◽  
Hydration Process ◽  
Cement Matrix ◽  
X Ray Diffraction ◽  
Structure Form ◽  
Silicate Phase ◽  
X Ray

The paper studies features of the hydration process of the modified blended cement for fiber cement panels (FCP) using differential thermal analysis, X-ray diffraction analysis, electron microscopy and infrared spectroscopy. It is found that deeper hydration process in silicate phase, denser and finer crystalline structure form in fiber cement matrix based on the modified blended cement. Generalization of this result to the case of fiber cement panels makes it possible to achieve formation of a denser and homogeneous structure with increased physical and mechanical properties.

Effect of Sintering Temperature on Microstructure and Mechanical Properties of Al2O3-TiC-ZrO2 Ceramic Composites

2012 ◽  
Vol 476-478 ◽  
pp. 1031-1035
Author(s):  
Wei Min Liu ◽  
Xing Ai ◽  
Jun Zhao ◽  
Yong Hui Zhou
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Relative Density ◽  
Sintering Temperature ◽  
Ceramic Composites ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

Al2O3-TiC-ZrO2ceramic composites (ATZ) were fabricated by hot-pressed sintering. The phases and microstructure of the composites were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The relative density and mechanical properties (flexural strength, fracture toughness and Vicker’s hardness) of the composites were tested. The results show that the microstructure of the composites was the gray core-white rim. With the increase of sintering temperature, the relative density and mechanical properties of the composites increased first and then decreased. The composite sintered at 1705°C has the highest synthetical properties, and its relative density, flexural strength, fracture toughness and Vickers hardness are 98.3%,970MPa,6.0 MPa•m1/2and 20.5GPa, respectively.

CHARACTERIZATION OF HYDROXYAPATITE/TI6AL4V COMPOSITE POWDER UNDER VARIOUS SINTERING TEMPERATURE

2015 ◽  
Vol 75 (7) ◽  
Author(s):  
Amir Arifin ◽  
Abu Bakar Sulong ◽  
Norhamidi Muhamad ◽  
Junaidi Syarif
Keyword(s):  
Mechanical Properties ◽  
Composite Powder ◽  
Sintering Temperature ◽  
Physical And Mechanical Properties ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
Different Temperatures ◽  
Two Phases ◽  
Work Interaction

Hydroxyapatite (HA) has been widely used in biomedical applications due to its excellent biocompatibility. However, Hydroxyapatite possesses poor mechanical properties and only tolerate limited loads for implants. Titanium is well-known materials applied in implant that has advantage in mechanical properties but poor in biocompatibility. The combination of the Titanium alloy and HA is expected to produce bio-implants with good in term of mechanical properties and biocompatabilty. In this work, interaction and mechanical properties of HA/Ti6Al4V was analyzed. The physical and mechanical properties of HA/Ti6Al4V composite powder obtained from compaction (powder metallurgy) of 60 wt.% Ti6Al4V and 40 wt.% HA and sintering at different temperatures in air were investigated in this study. Interactions of the mixed powders were investigated using X-ray diffraction. The hardness and density of the HA/Ti6Al4V composites were also measured. Based on the results of XRD analysis, the oxidation of Ti began at 700 °C. At 1000 °C, two phases were formed (i.e., TiO2 and CaTiO3). The results showed that the hardness HA/Ti6Al4V composites increased by 221.6% with increasing sintering temperature from 700oC to 1000oC. In contrast, the density of the composites decreased by 1.9% with increasing sintering temperature. 

Contribution of the hybrid component to the structure and properties of ceramics based on metastable phases Al2O3

2021 ◽  
pp. 127-136
Author(s):  
A. V. Maletsky ◽  
T. E. Konstantinova ◽  
D. R. Belichko ◽  
G. K. Volkova ◽  
V. V. Burkhovetsky
Keyword(s):  
Mechanical Properties ◽  
Yttrium Aluminum Garnet ◽  
Metastable Phase ◽  
Physical And Mechanical Properties ◽  
Structure And Properties ◽  
X Ray Diffraction ◽  
Mutual Inhibition ◽  
X Ray ◽  
Tetragonal Lattice ◽  
Yttrium Aluminum

The paper presents results of the study of the effect of doping with yttrium oxide on ceramics of the composition (γ + θ) Al2O3 + nY2O3 (n = 0, 1, 2, 3 wt%), sintered at 1550°C for 2 h, from powders of the specified composition annealed at temperatures of 500 , 800, 1000°С. X-ray diffraction analysis established the formation in ceramics of yttrium aluminum garnet Y3Al5O12 (YAG) and a metastable phase of the same composition with a tetragonal lattice type in powders at temperatures above 1200°C. The effect of YAG on the physical and mechanical properties was established: high properties were demonstrated by ceramics of the composition α-Al2O3 + 2wt% Y2O3, obtained from a powder annealed at 1000°C. In addition, high physical and mechanical properties were observed in ceramics of the composition α-Al2O3 + 0wt% Y2O3, obtained from a powder annealed at 800°C. The effect of the so-called “mutual protection against crystallization” was discovered, which consists in the mutual inhibition of crystallization processes in powders of the Al2O3 – Y2O3 system.

Physical and Mechanical Properties of Bi0.5(Na0.81K0.19)0.5TiO3 Ceramic Modified by KNbO3

2019 ◽  
Vol 805 ◽  
pp. 71-75
Author(s):  
Suchittra Inthong ◽  
Chatchai Kruae-In ◽  
Wuttikrai Thanomsiang ◽  
Suppanat Kosolwattana ◽  
Denis Russell Sweatman ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mixed Oxides ◽  
Perovskite Phase ◽  
Physical And Mechanical Properties ◽  
X Ray Diffraction ◽  
Solid State Reaction Technique ◽  
X Ray ◽  
Ceramic Samples ◽  
Pure Phase ◽  
Knoop Microhardness

This research reports the physical and mechanical properties of (1-x) Bi0.5(Na0.81K0.19)0.5TiO3-xKNbO3 (x=0.00-0.06) ceramics. The Modified Bi0.5(Na0.81K0.19)0.5TiO3 ceramics were synthesized by solid state reaction technique. The mixed oxides powders were calcined at 850 °C, 4 h and sintered at 1120 °C, 2 h to form pure phase perovskite and the optimum bulk density, respectively. The phase formation of the modified ceramic samples was determined by X-ray diffraction technique. All of the modified Bi0.5(Na0.81K0.19)0.5TiO3 ceramics exhibited a single perovskite phase. The bulk densities of the modified ceramic samples were 5.41±0.27-5.75±0.28 g/cm3 using the Archimedes’ method. The microstructure was revealed by the scanning electron microscope. The rectangular-like shape was found of all studied ceramics which had the grain size between 1.31±0.02-1.56±0.03 mm. The mechanical properties were studied by both Vickers and Knoop microhardness tester. The results are discussed in term of the relation among hardness properties, Young’s modulus, and fracture toughness.

Sign in / Sign up

Export Citation Format

Share Document