Blood Grouping with a Miniature Centrifugal Fast Analyzer

1974 ◽  
Vol 20 (8) ◽  
pp. 1043-1054
Author(s):  
T O Tiffany ◽  
J M Parella ◽  
C A Burtis ◽  
W F Johnson ◽  
C D Scott

Abstract The Centrifugal Fast Analyzer was used to develop a semiautomated, computerized blood-grouping system. A miniaturized version of the Analyzer was used for the development because, essentially, it enables one to automate "test-tube" grouping procedures. The blood-grouping system is discussed in terms of adaptation of blood-grouping procedures; types of instrumentation used for grouping, cell washing, and Coombs testing; parametric optimization of hemagglutination reactions; subgrouping of A and AB; reverse typing; small-scale blood-grouping evaluation of our approach; and computerization of blood grouping. The data reported here indicate that the system reliably provides accurate results.

Author(s):  
Andre´ L. C. Fujarra ◽  
Eduardo A. Tannuri ◽  
Isai´as Q. Masetti ◽  
Haroldo Igreja

The installations of sub-sea equipments are very complex operations, requiring previous analysis in order to define the correct procedure and the environmental “window” for a safe operation. This paper addresses the installations of a Mid Water Arch (MWA) that consists of a structure to provide risers support. Connecting the risers to the MWA largely eliminates the dynamic forces that would otherwise cause friction and fatigue. Such structure is composed by the riser guides and several buoyancy tanks. It is kept in the water by means of tethers connected to an anchor. The MWA is to be installed 42m from the seabed. The installation procedure has several steps evolving the launching of each component of the MWA (anchor, main structure and the tethers). A tug boat with an A-frame is used during the whole launching, and an assisting vessel is required to keep the buoy away from the tether and the launching cable. The presence of exciting waves induces oscillatory motions in the whole system, and may cause large dynamic forces in the cables and tethers. Due to the complexity of the multi-body system, a comprehensive numerical and experimental analysis was then carried out in order to dimensioning the launching cables and to define the limit environmental condition. The numerical analysis was carried out in the Numerical Offshore Tank (TPN), a multi-processor offshore system simulator that considers the 6 DOF of each body and all environmental forces acting in them. The lines are modeled by finite-element method. Furthermore, a full set of small-scale experiments were carried out at the State of Sa˜o Paulo Technological Research Institute (IPT) towing tank, considering the system excited by a sinusoidal motion at the top, emulating the wave excitation. Comparisons between numerical and experimental results were performed, with good adherence between them. The validated numerical simulator was then used to make predictions of the behavior of the systems during the installation, considering several environmental conditions and configurations.


Author(s):  
André Brack

Stanley Miller demonstrated in 1953 that it was possible to form amino acids from methane, ammonia, and hydrogen in water, thus launching the ambitious hope that chemists would be able to shed light on the origins of life by recreating a simple life form in a test tube. However, it must be acknowledged that the dream has not yet been accomplished, despite the great volume of effort and innovation put forward by the scientific community. A minima, primitive life can be defined as an open chemical system, fed with matter and energy, capable of self-reproduction (i.e., making more of itself by itself), and also capable of evolving. The concept of evolution implies that chemical systems would transfer their information fairly faithfully but make some random errors. If we compared the components of primitive life to parts of a chemical automaton, we could conceive that, by chance, some parts self-assembled to generate an automaton capable of assembling other parts to produce a true copy. Sometimes, minor errors in the building generated a more efficient automaton, which then became the dominant species. Quite different scenarios and routes have been followed and tested in the laboratory to explain the origin of life. There are two schools of thought in proposing the prebiotic supply of organics. The proponents of a metabolism-first call for the spontaneous formation of simple molecules from carbon dioxide and water to rapidly generate life. In a second hypothesis, the primeval soup scenario, it is proposed that rather complex organic molecules accumulated in a warm little pond prior to the emergence of life. The proponents of the primeval soup or replication first approach are by far the more active. They succeeded in reconstructing small-scale versions of proteins, membranes, and RNA. Quite different scenarios have been proposed for the inception of life: the RNA world, an origin within droplets, self-organization counteracting entropy, or a stochastic approach merging chemistry and geology. Understanding the emergence of a critical feature of life, its one-handedness, is a shared preoccupation in all these approaches.


Author(s):  
Concetta Tripepi ◽  
Francesco Nucera ◽  
Lawrence A. Bergman ◽  
D. Michael McFarland ◽  
Alexander F. Vakakis

The aim of this work is to show that is possible to apply the Nonlinear Energy Sink (NES) concept to protect seismically excited eccentric steel structures through Targeted Energy Transfer (TET). We consider, as the primary (linear) system, a small-scale four-storey unsymmetrical-plan building, modeled as a twelve-degree-of-freedom-system, with floors sufficiently rigid so that the frame can reasonably be considered as shear-type and with additional eccentric mass for each floor. To the primary (linear) system, we connect two NESs, which are non-smooth and precisely the vibro-impact devices (VI-NESs), both placed on the top floor. In order to analyze the dynamics of the controlled model (structure with VI-NESs), we study the performance and the robustness of the augmented structure excited by a set of Eurocode8 (EC8) spectrum compliant earthquakes. Our purpose is to check the effectiveness of the VI-NESs to different earthquake excitations, that is, testing that an optimal VI-NES setting computed for a specific earthquake will still produce satisfactory results for the other earthquakes. We show that the nonlinear attachments are capable of engaging in transient resonance with linear modes at arbitrary frequencies by generating a one-way irreversible (on the average) transfer of the energy of vibration from the primary structure to local attachment. There the energy is confined and locally dissipated without “spreading” back to the main structure because of the instantaneous internal resonance. As energy decreases due to damping the conditions for Transient Resonance Capture (TRC) fail and escape from resonance capture takes place.


2012 ◽  
Vol 162 ◽  
pp. 19-28 ◽  
Author(s):  
Jean Christophe Fauroux

Fast wheeled motion on unstructured grounds requires highly efficient suspensions that damp shocks vertically but also horizontally, which is an original contribution of the author. This work describes nine 2D and 3D kinematics, most of them with parallel structure, that are suitable for guiding a wheel and providing simultaneous damping in two directions. Steering and power transmission are also included in the most advanced variants, that were previously patented. Both structural and dimensional synthesis are presented, with a kinematic description of each system. A real implementation at a small scale is also described.


Author(s):  
Olaf O. Otte Filho ◽  
Rafael L. Tanaka ◽  
Rafael G. Morini ◽  
Rafael N. Torres ◽  
Thamise S. V. Vilela

In the design of flexible pipes, predict the anchoring behavior on end fittings is always challenging. In this sense, Prysmian Surflex has developed a finite element model, which should help the end fitting design as well the prediction of the structural behavior and the acceptable maximum loads. The current model considers that the contact between armor-resin is purely cohesive and has been suitable for the design of end fittings [1] and [2]. But tests and new studies [3] and [4] indicate that only cohesive assumption would not be the best approach. Experimental data from prototype tests also show that the current model would not predict acceptable results for loads higher than those used in previous projects. This document will describe a study developed considering the friction and thermal contraction, instead of the cohesive phenomenon in the anchoring behavior analysis. Small scale tests were conducted in order to understand the anchoring relation between the resin and the wire used in the tensile armor. For this purpose, a special test device was developed to simulate an enclosure system. A parametric study was also performed to identify the cooling temperatures, coefficients of friction and contact properties parameters taken from small scale tests. The finite element model considers the thermal effects during exothermic curing. Using the new parameters obtained, a second model was developed. This model consists of only one real shaped bended wire inside an end fitting cavity. To validate the model, samples were tested on laboratory according anchoring design. The results of this round of tests were studied and corroborate the argument that use friction and thermal effects is better than use only the cohesive condition.


Author(s):  
Yaodong Wang ◽  
Tarik Al-Shemmeri

A theoretical and an experimental investigation of a small scale trigeneration based on a diesel engine generator set is conducted. Comparing with the separate generation system, trigeneration saves primary energy input; and it reduces CO2 gas emission to the environment. A conclusion can be drawn that trigeneration is an environment friendly method, and it is financially feasible.


1943 ◽  
Vol 16 (3) ◽  
pp. 679-686
Author(s):  
B. S. Garvey

Abstract In research on rubber synthesis, as in any broad program of chemical research, it is a distinct advantage to be able to do all work on a normal laboratory or test-tube scale. With rubber, however, the standard laboratory testing methods require from 200 to 500 grams of rubber for each batch. Hence it was obvious that, if the advantages of small-scale work in the preparational stages were to be realized, a new technique of rubber testing would have to be developed. The use of entirely new and unrelated procedures has two definite objections. In the first place the new procedures must be thoroughly tested and compared with the older methods of testing or with the processing and use requirements of the new rubbers. In the second place the significance of the results of such new tests can be conveyed, even to experienced rubber technologists, only after considerable interpretation of the methods. It seemed best, therefore, to modify standard rubber-testing methods so that they could be applied to very small amounts of synthetic rubber. More recently, the shortage of natural rubber has made necessary a reduction in the amount of rubber used for testing. For this purpose the same small-scale procedures are highly advantageous. While some idea of the quality of a sample of natural or synthetic rubber can be obtained from examination of the crude rubber itself, it is much better to know the physical properties of the vulcanized product. This means that one or more balanced compounds must be mixed and tested. The purpose of this paper is to describe a technique which has been developed in the Goodrich laboratories whereby, with as little as 5 grams of rubber, the stress-strain characteristics may be determined, and with 9 grams of rubber a fairly comprehensive evaluation can be made. This method has been used to evaluate polymers made on the 10-gram scale by Fryling.


2020 ◽  
Vol 51 (3) ◽  
pp. 75-85
Author(s):  
S. Boudalia ◽  
Y. Gueroui ◽  
B. Boumaza ◽  
A. Bousbia ◽  
M. Benada ◽  
...  

Abstract For food industry, the production of functional pasta from non-conventional raw materials represents a challenge. This study aims to evaluate the potential of animal proteins of freeze-dried whey as a component for pasta production and its effect on the pasta qualities and consumer acceptance. Sweet whey was freeze-dried, then directly incorporated to pasta at a 20% level. Two pasta types (pasta non-enriched vs. enriched with whey powder) were manufactured following a small-scale pilot procedure, and then evaluated for their physicochemical and sensory qualities. Results of all analyses (whey, semolina and pasta) met the standards according to international legislation; however, the characteristics of enriched pasta differed. Whey addition significantly increased ash, proteins content, optimal cooking time and water uptake (P < 0.05); it significantly decreased moisture levels, colour parameters (CIE system: a* redness, b* yellowness) and the swelling index (P < 0.05). Sensory analysis revealed that overall sensory and product quality of enriched pasta was not affected by whey fortification and it was found acceptable by panelists. This study points out that whey powder could be used for the functional pasta production to increase proteins levels.


Sign in / Sign up

Export Citation Format

Share Document