scholarly journals Research on stress release for the gob-side roadway using the roof-cutting technology with a chainsaw arm

2020 ◽  
Vol 7 (3) ◽  
pp. 191663
Author(s):  
Yang Tai ◽  
Bin Yu ◽  
Binwei Xia ◽  
Zhao Li ◽  
Hongchu Xia
Keyword(s):  
Numerical Analysis ◽  
Coal Pillar ◽  
Deformation And Failure ◽  
Hard Roof ◽  
Working Face ◽  
Stress Relieving ◽  
Cutting Experiment ◽  
Pillar Mining ◽  
Coal Pillars ◽  
Cutting Height

The narrow pillar mining method is widely adopted for working faces in coal mines. However, in cases of an overlying hard roof, a suspended triangle roof plate or a cantilever will be formed near the goaf. At this point, the coal pillar extrusion and serious deformation will occur in the gob-side roadway. In order to mitigate the problem, the roof-cutting technology with a chainsaw arm and its equipment have been developed. In this paper, based on the analysis of deformation and failure characteristics of 2312 roadway, which is close to the goaf of 2311 working face in Tashan Coal, the roof-cutting technology with a chainsaw arm was chosen to be applied in 2311 roadway. Then, the roof-cutting process and the load acting on the coal pillar were discussed and analysed. A numerical model was established to analyse the stress releasing effects after roof cutting. Moreover, the roof-cutting height and the support parameters of the roadway were optimized through numerical analysis and the results manifested that the roof cutting was the most effective when the roof-cutting height was 6.4 m. After roof cutting, the vertical stresses within the coal pillars were lowered by about 25.0%. Finally, the roof-cutting experiment was carried out in the 2311 roadway in Tashan Coal Mine. The on-site roof-cutting depth was 6.4 m and the roof-cutting width was 42 mm guided by the numerical analysis. To verify the stress-relieving effects, the borehole stress meters were applied to monitor the peak advancing stresses of narrow pillars at various depths. The measured results indicated that the peak advancing stresses decreased by 22.8% on average, and therefore, roof cutting and stress releasing effects were achieved.

The Optimization Research of Wide Strip and Full-Pillar Mining under Villages

2012 ◽  
Vol 616-618 ◽  
pp. 406-410
Author(s):  
Gui Liu ◽  
Hua Xing Zhang ◽  
Jin Hui Chen ◽  
Chao Gao
Keyword(s):  
Surface Structures ◽  
Strip Mining ◽  
Mining Method ◽  
Sequence Optimization ◽  
Wide Strip ◽  
Deformation Limit ◽  
Working Face ◽  
Specific Analysis ◽  
Pillar Mining ◽  
Coal Pillars

By making full use of the advantages of strip mining method and full-pillar mining method, the wide strip and full-pillar mining method can achieve the aim of mining under villages. However, at the full-pillar mining stage, the difficulty in managing several workfaces which are at work at the same time still exists. To improve the wide strip and full-pillar mining method’s applicability, an optimization of extraction sequence for coal pillars instead of the multi-working-face is put forward at the stage of full-pillar mining, and in the case of the deformation limit of surface structures is satisfied, to extract all the coal pillars which are under villages. By specific analysis of the extraction sequence optimization of the coal pillars in No.1 mine under Qian Xudapo village which belongs to Chang Chun coal Co., LTD., a better result is got which also acts a technological reference for the extraction under villages.

scholarly journals Study on the Fracture Law of Inclined Hard Roof and Surrounding Rock Control of Mining Roadway in Longwall Mining Face

Energies ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 5344
Author(s):  
Feng Cui ◽  
Shuai Dong ◽  
Xingping Lai ◽  
Jianqiang Chen ◽  
Chong Jia ◽  
...  
Keyword(s):  
Energy Release ◽  
Longwall Mining ◽  
Coal Pillar ◽  
High Energy ◽  
Mechanical Analysis ◽  
Engineering Practice ◽  
Analysis Model ◽  
Hard Roof ◽  
Working Face ◽  
The Stability

In the inclination direction, the fracture law of a longwall face roof is very important for roadway control. Based on the W1123 working face mining of Kuangou coal mine, the roof structure, stress and energy characteristics of W1123 were studied by using mechanical analysis, model testing and engineering practice. The results show that when the width of W1123 is less than 162 m, the roof forms a rock beam structure in the inclined direction, the floor pressure is lower, the energy and frequency of microseismic (MS) events are at a low level, and the stability of the section coal pillar is better. When the width of W1123 increases to 172 m, the roof breaks along the inclined direction, forming a double-hinged structure, the floor pressure is increased, and the frequency and energy of MS events also increases. The roof gathers elastic energy release, and combined with the MS energy release speed it can be considered that the stability of the section coal pillar is better. As the width of W1123 increases to 184 m, the roof in the inclined direction breaks again, forming a multi-hinged stress arch structure, and the floor pressure increases again. MS high-energy events occur frequently, and are not conducive to the stability of the section coal pillar. Finally, through engineering practice we verified the stability of the section coal pillar when the width of W1123 was 172 m, which provides a basis for determining the width of the working face and section coal pillar under similar conditions.

scholarly journals Investigation of Strong Strata Behaviors in the Close-Distance Multiseam Coal Pillar Mining

2021 ◽  
Vol 2021 ◽  
pp. 1-14
Author(s):  
Hongwei Mu ◽  
Yongsheng Bao ◽  
Dazhao Song ◽  
Dongfang Su
Keyword(s):  
Computed Tomography ◽  
Theoretical Model ◽  
Stress Concentration ◽  
Stress Distribution ◽  
Coal Pillar ◽  
High Energy ◽  
Support Pressure ◽  
Pillar Mining ◽  
Coal Pillars ◽  
Close Distance

According to the new stress distribution pattern and the strong strata behaviors as the characteristics of the coal pillars in the close-distance multiseam coal pillar mining, the common characteristics of different types of overlying coal pillars were summarized and analyzed. Moreover, a theoretical model for the mechanism of strong strata behaviors in the close-distance multiseam coal pillar mining was established, which was validated by the monitoring data of seismic computed tomography CT, microseism, and electromagnetic radiation (EMR). Furthermore, the results of the study indicated that the main factors affecting the strong strata behaviors were the static stress concentration caused by the overlying coal pillars and the dynamic disturbance caused by the fracturing and slipping of the overlying coal pillars and roof under the influence of mining. In the case of Xinzhouyao coal mine, the transmitted stress and lateral support pressure of the overlying coal pillars accounted for 78.3% and 16% of the vertical concentrated stress, respectively, and the areas closer to the overlying coal pillars were more susceptible to dynamic load disturbances. The monitoring results of seismic computed tomography CT and EMR demonstrated the static load stress concentration area was distributed near the overlying coal pillar, and the stress concentration degree was greater in the area of superimposed lateral support pressure and advanced support pressure. Moreover, microseismic spatial positioning revealed that the high-energy microseismic events were mainly concentrated near the overlying large coal pillars and roof. The on-site multiparameter detection results were highly consistent with the characteristics of actual strata behaviors and the conclusions of the theoretical model. This method could provide a reference for the quantitative calculation of stress distribution under similar conditions and the identification of the danger zone of strata behaviors.

scholarly journals Research on Failure Mechanism and Strengthening of Broken Roadway Affected by Upper Coal Pillar

2019 ◽  
Vol 2019 ◽  
pp. 1-13 ◽  
Author(s):  
Fulian He ◽  
Zheng Zheng ◽  
Hengzhong Zhu ◽  
Bo Yang
Keyword(s):  
Stress Distribution ◽  
Failure Mechanism ◽  
Coal Pillar ◽  
Control Area ◽  
Surrounding Rock ◽  
Horizontal Line ◽  
Protective Function ◽  
Working Face ◽  
Coal Pillars ◽  
Roadway Deformation

The principal stress difference is introduced as a new evaluation index in order to better understand the failure mechanism of roadways affected by upper coal pillars and characterize failure of rock mass. Compared with traditional methods, it facilitates quantitative analysis. Moreover, we combine the semiplane theory and we obtain the stress distribution on the coal pillar’s bedrock and the strengthening control area from the “change point” position along a 21 m horizontal line. The influence of multiple stresses induced from mining on a roadway is analyzed. It is found that rock failure is most likely while mining the 051606 working face, followed by mining the 051604 working face, and the stress influence on the upper pillar has the lowest failure probability. In addition, based on the asymmetry of the surrounding rock stress distribution, this study proposes strengthening control technology of surrounding rock on the basis of a highly stressed bolting support and anchor cable, adding to the steel ladder beam, steel mesh, and shed support’s protective function to the roadway’s roof and ribs. Finally, through field observations, it is concluded that the roadway deformation is within the controllable range.

scholarly journals A physical model study of surrounding rock failure near a fault under the influence of footwall coal mining

2020 ◽  
Author(s):  
Shukun Zhang ◽  
Lu Lu ◽  
Ziming Wang ◽  
Shuda Wang
Keyword(s):  
Rock Mass ◽  
Physical Model ◽  
Hanging Wall ◽  
Coal Pillar ◽  
Vertical Displacement ◽  
Surrounding Rock ◽  
Pillar Width ◽  
Model Study ◽  
Working Face ◽  
Coal Pillars

AbstractA study of the deformation of the surrounding rock and coal pillars near a fault under the influence of mining is conducted on a physical model for the design of coal pillars to support and maintain the roofs of adjacent fault roadways. This research is based on the 15101 mining face in the Baiyangling Coal Mine, Shanxi, China, and uses simulation tests similar to digital speckle test technology to analyse the displacement, strain and vertical stress fields of surrounding rocks near faults to determine the influence of the coal pillar width. The results are as follows. The surrounding rock of the roadway roof fails to form a balance hinge for the massive rock mass. The vertical displacement, vertical strain and other deformation of the surrounding rock near the fault increase steeply as the coal pillar width decreases. The steep increase in deformation corresponds to a coal pillar width of 10 m. When the coal pillar width is 7.5 m, the pressure on the surrounding rock near the footwall of the fault suddenly increases, while the pressure on the hanging wall near the fault increases by only 0.35 MPa. The stress of the rock mass of the hanging wall is not completely shielded by the fault, and part of the load disturbance is still transmitted to the hanging wall via friction. The width of the fault coal pillars at the 15101 working face is determined to be 7.5 m, and the monitoring data verify the rationality of the fault coal pillars.

scholarly journals Study on Stress Relief of Hard Roof Based on Presplitting and Deep Hole Blasting

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Peng Gong ◽  
Yongheng Chen ◽  
Zhanguo Ma ◽  
Shixing Cheng
Keyword(s):  
Stress Distribution ◽  
Coal Mine ◽  
Coal Pillar ◽  
Deep Hole ◽  
Hard Roof ◽  
Formation Conditions ◽  
Coal Pillars ◽  
Mining Coal ◽  
The Impact ◽  
Pillar Size

For the problem that the hard roof causes wider end-mining coal pillar, and the roadway is greatly affected by mining, this paper took Shanxi Luning Coal Mine as the engineering background; based on the stress distribution characteristics of the coal pillar, the calculation method of the limit end-mining coal pillar size was given; considering the formation conditions and transmission forms of the advanced abutment stress, a method combining presplitting and deep hole blasting was proposed to weaken the advanced abutment stress. The numerical simulation was used to analyze the stress distribution of coal pillars, which was verified by on-site industrial tests. The results showed that the presplitting can achieve the blocking of stress. The closer it is to the peak of the abutment stress, the better the blocking effect. Deep hole blasting can weaken the source of the advanced abutment stress and reduce the peak of abutment stress. With the combination of the two blasting methods, the end-mining coal pillar size of Luning Coal Mine can be reduced to 60 m. The method combining presplitting and deep hole blasting can effectively reduce the end-mining coal pillar size and reduce the impact of mining on the deformation of the dip roadway.

scholarly journals Simulation Analysis and Engineering Application of Retaining Width of Waterproof Coal Pillar in Island Working Face

2021 ◽  
Author(s):  
Lili Zheng ◽  
Zheng Gao
Keyword(s):  
Service Life ◽  
Simulation Analysis ◽  
Engineering Application ◽  
Coal Pillar ◽  
Surrounding Rock ◽  
Simulation Research ◽  
Working Face ◽  
Before And After ◽  
Mining Face ◽  
Coal Pillars

The old mining area in Pingdingshan coalfield has the following problems: long mining service life, many remaining coal pillars, and great difficulty in mining; to extend the service life of the mine, realize cost saving and efficiency increasing, it is urgent to recover the remaining coal pillars, but the mining of isolated island face faces the problem of reasonable retention of waterproof coal pillars, if the protection is not good, it is easy to cause mine water damage and increase the mining cost. Therefore, in view of the practical engineering problems faced by the field, aiming at eliminating or reducing the goaf water disaster, this paper adopts numerical simulation research methods to optimize the original design scheme and carry out comparative analysis, dynamically reappear the surrounding rock stress field, displacement field and plastic failure law under multi face mining and roadway mining, and carry out engineering practice application. The results show that there is a certain thickness of elastic core area before and after mining with 25m coal pillar width. The deformation of surrounding rock is small, which is conducive to roadway maintenance, without obvious stress concentration. It can meet the actual needs of the project. The mining face has achieved safe mining, without water inrush accident in the goaf, and the coal resources have been recovered to the maximum extent. The research results are left over to similar mining areas in China The safe recovery of coal pillar can be used for reference.

scholarly journals Research on Reasonable Width of Coal Pillars of Non-equal Width Isolated Working Face Heading Goaf in Deep Mine

2021 ◽  
Author(s):  
weili yang ◽  
Quande wei ◽  
Zhonghui Wang ◽  
Zhizeng Zhang ◽  
Xiaocheng Qu ◽  
...  
Keyword(s):  
Rock Burst ◽  
Critical State ◽  
Research Result ◽  
High Stress ◽  
Coal Pillar ◽  
Stress Monitoring ◽  
Equilibrium Relation ◽  
Deep Mine ◽  
Working Face ◽  
Coal Pillars

Abstract Setting reasonable coal pillar is a key to ensure safe mining of island coal face heading goaf in deep mine. With determination of reasonable width of coal pillars of non-equal width isolated working face 3201 in worked-out area in one mine in Shandong as the engineering background, a research was conducted on the mechanism of rock burst induced by and the reasonable width of coal pillars of isolated working face in worked-out area and the main conclusions are as follows: (1) the coal pillars of isolated working face 3201 in worked-out area changed from pillars with goaf on two sides→pillars with goaf on three sides→pillars with goaf on four sides, resulting in evolution of overlying strata from pre-mining static “┒-shaped” structure→“C-shaped” structure→“O-shaped” structure and corresponding spatial stress from “saddle-shaped” profile→“platform-shaped” profile→“arch-shaped” profile; (2) the rock burst was induced by coal pillars, because the high stress on coal pillars at critical state of a rock burst was greater than their comprehensive strength and induced a rock burst due to sudden instability; (3) by establishing a bearing and load model of coal pillars at critical state of a rock burst and based on the equilibrium relation, an method for estimating reasonable width of coal pillars of isolated working face in worked-out area in deep mine was derived and applied to the isolated working face 3201 in worked-out area, thus comprehensively determining that the width of coal pillars should be 130m. The field stress monitoring verified the reasonability. The research result is of great significance to prevention of rock burst induced by coal pillars of isolated working face in worked-out area in deep mine.

scholarly journals Analysis on Rock Burst Risks and Prevention of a 54 m-Wide Coal Pillar for Roadway Protection in a Fully Mechanized Top-Coal Caving Face

2021 ◽  
Vol 2021 ◽  
pp. 1-7
Author(s):  
Zhihua Li ◽  
Ke Yang ◽  
Jianshuai Ji ◽  
Biao Jiao ◽  
Xiaobing Tian
Keyword(s):  
Coal Seam ◽  
Rock Burst ◽  
Influencing Factors ◽  
Abutment Pressure ◽  
Large Diameter ◽  
Coal Pillar ◽  
Distribution Characteristics ◽  
Pressure Relief ◽  
Working Face ◽  
Coal Pillars

A case study based on the 401103 fully mechanized caving face in the Hujiahe Coal Mine was carried out in this research to analyze the rock burst risks in a 54 m-wide coal pillar for roadway protection. Influencing factors of rock burst risks on the working face were analyzed. Stress distribution characteristics on the working face of the wide coal pillar for roadway protection were discussed using FLAC3D numerical simulation software. Spatial distribution characteristics of historical impact events on the working face were also investigated using the microseismic monitoring method. Results show that mining depth, geological structure, outburst proneness of coal strata, roof strata structure, adjacent mining area, and mining influence of the current working face are the main influencing factors of rock burst on the working face. Owing to the collaborative effects of front abutment pressure of the working face and lateral abutment pressure in the goaf, the coal pillar is in the ultimate equilibrium state and microseismic events mainly concentrate in places surrounding the coal pillars. Hence, wide coal pillars become the regions with rock burst risks on the working face. The working face adopts some local prevention technologies, such as pressure relief through presplitting blasting in roof, pressure relief through large-diameter pores in coal seam, coal seam water injection, pressure relief through large-diameter pores at bottom corners, and pressure relief through blasting at bottom corners. Moreover, some regional prevention technologies were proposed for narrow coal pillar for roadway protection, including gob-side entry, layer mining, and fully mechanized top-coal caving face with premining top layer.

scholarly journals Dynamic Evolution Law and Width Determination of Section Coal Pillars in Deep Mining Height Working Face

2021 ◽  
Author(s):  
Lei Zhaoyuan ◽  
Cui Feng ◽  
Liu Jianwei ◽  
Lai Xingping ◽  
Yi Ruiqiang
Keyword(s):  
Dynamic Instability ◽  
Coal Pillar ◽  
Field Measurements ◽  
Deep Mining ◽  
Evolution Law ◽  
Working Face ◽  
Large Mining Height ◽  
Coal Pillars ◽  
Lower Corner ◽  
Mining Height

Abstract The coal column undergoes three types of force evolution from the formation to the end of mining. This paper takes large mining height working face at No.2 Coal Mine as example to study the ways to avoid dynamic instability of the coal column triggered by the deep mining. By means of geological survey, theoretical analysis, numerical calculation and field verification, the load processes under the three stress stage are proposed, and the evolution law of the coal column is analyzed. The study shows that the depth, large mining height working face, coal pillar force and size altogether determine the damage characteristics of the coal pillar. With the combination of Flac3D and 3DEC, it can be analyzed that the plastic failure and displacement characteristics of the 35m coal column under the action of secondary dynamic load coincide. The perturbation stress distribution is stable, which finally determines the reasonable width of the 35m coal column. Field measurements show that the top and gang of the 35m coal column undergo three kinds of displacement characteristics. The lower part is more stable. The top plate of the upper and lower corner completely collapsed in the emptying area, which can play a good supporting role.

Sign in / Sign up

Export Citation Format

Share Document