Residual stresses in tool steel due to hard-turning

2003 ◽  
Vol 36 (5) ◽  
pp. 1135-1143 ◽  
Author(s):  
Nerea Ordás ◽  
Mari Luz Penalva ◽  
Justino Fernández ◽  
Carmen García-Rosales
Keyword(s):  
Residual Stresses ◽  
Hard Turning ◽  
Stress Gradient ◽  
Cutting Tools ◽  
Machining Parameters ◽  
X Ray Diffraction ◽  
Brittle Layer ◽  
Aisi D2 ◽  
Full Stress Tensor ◽  
Compressive Residual Stresses

Residual stresses induced by hard-turning are the result of a combination of mechanical and thermal effects, leading to a compressive or tensile stress state at the surface, depending on the machining parameters and the tool wear state. In this work, the residual stress depth profiles generated on steel grade F-521 (AISI D2) by hard-turning with tools of different wear states were measured by X-ray diffraction. An integral method was applied to determine the full stress tensor and the stress gradient tensors in the tangential, radial and depth directions. Both macroscopic and microscopic residual stresses were investigated. Compressive residual stresses were measured below the surface in all machined specimens. The magnitude of the compressive stress was much lower and the depth was much shallower when using new cutting tools than when using worn tools. However, the sample that has been hard-turned with a worn tool suffered strong microstructural changes in a layer more than 150 µm thick, especially at the surface, where the presence of a hard and very brittle layer of untempered martensite was evidenced.

scholarly journals X-ray Determination of Compressive Residual Stresses in Spring Steel Generated by High-Speed Water Quenching

Materials ◽  
2019 ◽  
Vol 12 (7) ◽  
pp. 1154
Author(s):  
Diego E. Lozano ◽  
George E. Totten ◽  
Yaneth Bedolla-Gil ◽  
Martha Guerrero-Mata ◽  
Marcel Carpio ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Residual Stresses ◽  
High Speed ◽  
Spring Steel ◽  
X Ray Diffraction ◽  
Laboratory Equipment ◽  
X Ray ◽  
Water Chamber ◽  
Hardened Case ◽  
Compressive Residual Stresses

Automotive components manufacturers use the 5160 steel in leaf and coil springs. The industrial heat treatment process consists in austenitizing followed by the oil quenching and tempering process. Typically, compressive residual stresses are induced by shot peening on the surface of automotive springs to bestow compressive residual stresses that improve the fatigue resistance and increase the service life of the parts after heat treatment. In this work, a high-speed quenching was used to achieve compressive residual stresses on the surface of AISI/SAE 5160 steel samples by producing high thermal gradients and interrupting the cooling in order to generate a case-core microstructure. A special laboratory equipment was designed and built, which uses water as the quenching media in a high-speed water chamber. The severity of the cooling was characterized with embedded thermocouples to obtain the cooling curves at different depths from the surface. Samples were cooled for various times to produce different hardened case depths. The microstructure of specimens was observed with a scanning electron microscope (SEM). X-ray diffraction (XRD) was used to estimate the magnitude of residual stresses on the surface of the specimens. Compressive residual stresses at the surface and sub-surface of about −700 MPa were obtained.

Influence of Milling Parameters on Surface Residual Stresses of 7050-T7451 Aluminum Alloy

2012 ◽  
Vol 723 ◽  
pp. 208-213 ◽  
Author(s):  
Yi Wan ◽  
Chen Li ◽  
Zhan Qiang Liu ◽  
Shu Feng Sun
Keyword(s):  
Aluminum Alloy ◽  
Residual Stresses ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Milling Process ◽  
X Ray Diffraction ◽  
Orthogonal Direction ◽  
Mechanical Coupling ◽  
Surface Residual Stresses ◽  
Compressive Residual Stresses

Residual stresses generated in milling process affect the performance of machined components. Milling residual stresses correlate closely with the cutting parameters. In this paper, the generation and distribution of surface residual stresses in milling of aluminum alloy 7050-T7451 was investigated. The cutting speed changes from 300m/min to 3000m/min. In the experiments, the residual stresses on the surface of specimen are detected by X-ray diffraction technique. The result shows that compressive residual stresses are generated when cutting speed is under 500 m/min. In feed and its orthogonal direction, the effect of cutting speed and feed rate on residual stresses is similar. The formation of the residual stresses can be explained by thermo-mechanical coupling effects.

Investigation of Residual Stresses in a Sleeve Coldworked Lug Specimen by Neutron and X-ray Diffraction

1994 ◽  
Vol 38 ◽  
pp. 455-461
Author(s):  
R. Lin ◽  
B. Jaensson ◽  
T. M. Holden ◽  
R. B. Rogge ◽  
J. H. Root
Keyword(s):  
Fatigue Life ◽  
Residual Stresses ◽  
Fatigue Cracks ◽  
Fatigue Properties ◽  
Aircraft Industry ◽  
X Ray Diffraction ◽  
X Ray ◽  
Initiation And Propagation ◽  
Structural Parts ◽  
Compressive Residual Stresses

Sleeve coldworking (SCW) is a mechanical process used in the aircraft industry to strengthen fastener holes of structural parts. By cold-expanding the holes, compressive residual stresses and a high dislocation density are introduced around the holes, the effect of which is to counteract the initiation and propagation of fatigue cracks and thus increase the fatigue life of the parts. The knowledge of residual stress due to SCW is therefore crucial for assessing the fatigue properties of a treated part. In this study, residual stresses were investigated, by employing neutron and X-ray diffraction methods, in a lug specimen that was sleeve coldworked and fatigued. The specimen had been used for testing the influence of the SCW process on fatigue life and crack propagation behaviour under constant amplitude or variable amplitude cyclic loading.

Effect of Cutting-Edge Geometry and Workpiece Hardness on Surface Residual Stresses in Finish Hard Turning of AISI 52100 Steel

1999 ◽  
Vol 122 (4) ◽  
pp. 642-649 ◽  
Author(s):  
Jeffrey D. Thiele ◽  
Shreyes N. Melkote ◽  
Roberta A. Peascoe ◽  
Thomas R. Watkins
Keyword(s):  
Residual Stresses ◽  
Hard Turning ◽  
Cutting Edge ◽  
Edge Geometry ◽  
Surface Residual Stresses ◽  
Aisi 52100 ◽  
Aisi 52100 Steel ◽  
Finish Hard Turning ◽  
Hardness Values ◽  
Compressive Residual Stresses

An experimental investigation was conducted to determine the effects of tool cutting-edge geometry (edge preparation) and workpiece hardness on surface residual stresses for finish hard turning of through-hardened AISI 52100 steel. Polycrystalline cubic boron nitride (PCBN) inserts with representative types of edge geometry including “up-sharp” edges, edge hones, and chamfers were used as the cutting tools in this study. This study shows that tool edge geometry is highly influential with respect to surface residual stresses, which were measured using x-ray diffraction. In general, compressive surface residual stresses in the axial and circumferential directions were generated by large edge hone tools in longitudinal turning operations. Residual stresses in the axial and circumferential directions generated by large edge hone tools are typically more compressive than stresses produced by small edge hone tools. Microstructural analysis shows that thermally-induced phase transformation effects are present at all feeds and workpiece hardness values with the large edge hone tools, and only at high feeds and hardness values with the small edge hone tools. In general, continuous white layers on the workpiece surface correlate with compressive residual stresses, while over-tempered regions correlate with tensile or compressive residual stresses depending on the workpiece hardness. [S1087-1357(00)00304-X]

Residual Stresses in Multilayer Welds with Different Martensitic Transformation Temperatures Analyzed by High-Energy Synchrotron Diffraction

2011 ◽  
Vol 681 ◽  
pp. 37-42 ◽  
Author(s):  
Arne Kromm ◽  
Thomas Kannengiesser ◽  
Jens Altenkirch ◽  
Jens Gibmeier
Keyword(s):  
Residual Stress ◽  
Phase Transformation ◽  
Residual Stresses ◽  
Weld Metal ◽  
High Energy ◽  
X Ray Diffraction ◽  
Surface Areas ◽  
Transformation Mechanisms ◽  
Positive Effect ◽  
Compressive Residual Stresses

Low Transformation Temperature (LTT) alloys were developed in order to control the residual stress development by the martensitic phase transformation already during cooling of the weld metal. The positive effect of such LTT alloys on the mitigation of detrimental tensile residual stresses during welding has already been confirmed on the basis of individual laboratory tests. Within the current project it was experimentally investigated whether the phase transformation mechanisms are effective under increased restraint due to multi-pass welding of thicker specimens. The local residual stress depth distribution was analyzed non-destructively for V-type welds processed by arc welding using energy dispersive synchrotron X-ray diffraction (EDXRD). The use of high energy (20 keV to 150 keV) EDXRD allowed for the evaluation of diffraction spectra containing information of all contributing phases. As the investigated LTT alloy contains retained austenite after welding, this phase was also considered for stress analysis. The results show in particular how the constraining effect of increased thickness of the welded plates and additional deposited weld metal influences the level of the residual stresses in near weld surface areas. While the longitudinal residual stresses were reduced in general, in the transition zone from the weld to the heat-affected zone (HAZ) compressive residual stresses were found.

Non-Destructive Residual Stress Analysis of Induction Hardened Components by Neutron and X-Ray Diffraction

2013 ◽  
Vol 768-769 ◽  
pp. 420-427 ◽  
Author(s):  
Jeremy Epp ◽  
Thilo Pirling ◽  
Thomas Hirsch
Keyword(s):  
Residual Stress ◽  
Chemical Composition ◽  
Residual Stresses ◽  
Stress Analysis ◽  
Stress Gradient ◽  
X Ray Diffraction ◽  
Neutron Measurement ◽  
X Ray ◽  
Layer Removal ◽  
Residual Stress Analysis

In this paper the microstructural and residual-stress analysis of an induction hardened plate of medium carbon steel is described. The stress gradient was determined using laboratory X-ray diffraction (IWT, Bremen, Germany) and neutron strain scanning (ILL, Grenoble, France). Due to slight variations of chemical composition in the depth, matchstick like (cross section 2×2mm²) d0-reference samples were prepared from a similarly treated sample. The d0shift induced by variation of chemical composition was measured by neutron and by X-ray diffraction along the strain free direction (sin²ψ*) and used for the evaluation of the neutron stress calculation. The d0distribution obtained from the neutron measurement did not appear reliable while the method using X-ray diffraction seems to be an efficient and reliable method to determine d0profiles in small samples. The evaluation of neutron measurements was then done using the X-ray diffraction d0distribution. High compressive residual stresses were measured in the hardened layer followed by high tensile residual stresses in the core. A comparison of the neutron measurements with X-ray diffraction (XRD) depth profiles obtained after successive layer removal showed that both methods give similar results. However, these investigations opened the question about the direct comparison of the residual stresses obtained by neutron and XRD. Indeed, a correction of the neutron data regarding the residual stresses in thickness direction might be necessary as these are released in the case of X-ray diffraction measurements after layer removal.

Analysis of Surface Integrity for DIN 100Cr6 Steel Conical Bearing Rings after Hard Turning

2011 ◽  
Vol 223 ◽  
pp. 473-482 ◽  
Author(s):  
Sergio Delijaicov ◽  
Carlos Eddy Valdez Salazar ◽  
Éd Claudio Bordinassi ◽  
Linilsson Rodrigues Padovese
Keyword(s):  
Tool Wear ◽  
Residual Stresses ◽  
Hard Turning ◽  
White Layer ◽  
Cutting Speed ◽  
Hole Drilling ◽  
Machining Parameters ◽  
Hole Drilling Method ◽  
Conical Bearing ◽  
Bearing Rings

This work studies the influence of machining parameters, such as cutting speed and forces, feed rate, cutting depth, and tool flank wear, on the generation of surface residual stresses in DIN 100Cr6 steel conical bearing rings submitted to a hard turning process. A complete factorial planning was used to perform the tests and projected measurement. Cutting forces were measured by a piezoelectric dynamometer and residual stresses were determined by the hole-drilling method using strain gage. Results showed that after 2000 m of tool machining, phase transformations had been observed on sample surfaces, with white layer formation, and deeper, a dark layer whose thickness varied depending on the severity level of turning and the tool wear (in machined distance). Increase in tool wear generated minor values of compressive residual stresses and the surface roughness presented almost the same values in all experiments, except when the bigger parameters were used.

scholarly journals INVESTIGATION OF SURFACE MACROSCOPIC RESIDUAL STRESSES OF CUTTING CERAMICS AFTER MECHANICAL MACHINING

2018 ◽  
Vol 17 ◽  
pp. 6
Author(s):  
Jakub Němeček ◽  
Jiří Čapek ◽  
Nikolaj Ganev ◽  
Kamil Kolařík
Keyword(s):  
Residual Stresses ◽  
Surface Structure ◽  
Cemented Carbides ◽  
Machining Parameters ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cutting Ceramics ◽  
Mechanical Machining

Currently, the extensive research in the field of cutting ceramics is conducted and there are efforts to replace cemented carbides by these materials. However, the problem is to improve the production of ideal compact samples. Therefore, the influence of mechanical machining technologies on the values of macroscopic residual stresses was investigated by X-ray diffraction. The resulting values were discussed depending on machining parameters and surface structure of the studied samples.

scholarly journals Effect of Speed, Feed and Depth of Cut on Machining Induced Residual Stresses in Aisi 1045 Steel

2019 ◽  
Vol 8 (2) ◽  
pp. 3397-3400 ◽  
Keyword(s):  
Residual Stresses ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
X Ray Diffraction ◽  
Left Behind ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
Predicted Values ◽  
Future Work ◽  
1045 Steel

Residual stress that are induced during machining of components plays a significant part in the endurance and life of the component. The magnitude and nature of the residual stresses have been of interest to many researchers across the globe. The present work involves methodology to find out the influence of factors on the residual stresses. The machining parameters were varied and the residual stresses were determined using non-destructive method, namely X-ray diffraction. Using statistical methods, the influence of the machining parameters was ascertained. This paper aims at investigating the residual stresses in AISI 1045 steel, induced due to milling. AISI 1045 steel was considered as it is a widely used material and its applications are innumerable. It was observed that speed and feed have significant influence on stresses left behind after the machining is completed. Using statistical techniques a mathematical model was developed which is further used to predict the residual stresses. The error percentage of the predicted values was less than 5%. The results obtained were promising and future work involves the optimization of the machining parameters.

Characterization of Zirconia-Based Ceramics After Microgrinding

2019 ◽  
Vol 7 (2) ◽  
Author(s):  
Pablo Fook ◽  
Oltmann Riemer
Keyword(s):  
Surface Roughness ◽  
Flexural Strength ◽  
Residual Stresses ◽  
Machining Parameters ◽  
X Ray Diffraction ◽  
Four Point Bending ◽  
Ductile Mode ◽  
Recent Developments ◽  
Vibration Assistance ◽  
Diamond Grain

Despite the recent developments of ductile mode machining, microgrinding of bioceramics can cause an insufficient surface and subsurface integrity due to the inherent hardness and brittleness of such materials. This work aims to determine the influence of a two-step grinding operation on zirconia-based ceramics. In this regard, zirconia (ZrO2) and zirconia toughened alumina (ZTA) specimens are ground with ultrasonic vibration assistance within a variation of the machining parameters using two grinding steps and different diamond grain sizes of the tools in each of the machining procedure. White light interferometry, scanning electron microscope, X-ray diffraction (XRD), and four-point bending tests are performed to evaluate surface roughness, microstructure, residual stresses, and flexural strength, respectively. The strategy applied suggests that the finished parts are suitable for certain biomedical uses like dental implants due to their optimum surface roughness. Moreover, concerning the mechanical properties, an increase of the flexural strength and compressive residual stresses of ground ZrO2 and ZTA workpieces were observed in comparison to the as-received specimens. These results, as well as the methodology proposed to investigate the surface integrity of the ground workpieces, are helpful to understand the bioceramic materials response under microgrinding conditions and to set further machining investigations.

Sign in / Sign up

Export Citation Format

Share Document