Effect of cold vapour treatment on geometric accuracy of fused deposition modelling parts

2017 ◽  
Vol 23 (6) ◽  
pp. 1226-1236 ◽  
Author(s):  
Ashu Garg ◽  
Anirban Bhattacharya ◽  
Ajay Batish
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Fused Deposition Modelling ◽  
Curved Surfaces ◽  
Geometric Accuracy ◽  
Content Type ◽  
Fused Deposition ◽  
Cold Vapour ◽  
Side Face ◽  
Functional Components

Purpose The purpose of this paper is to investigate the influence of low-cost chemical vapour treatment process on geometric accuracy and surface roughness of different curved and freeform surfaces of fused deposition modelling (FDM) specimens build at different part building orientations. Design/methodology/approach Parts with different primitive and curved surfaces are designed and modelled to build at three different part orientations along X orientation (vertical position resting on side face), Y orientation (horizontal position resting on base) and Z orientation (upright position). Later, the parts are post-processed by cold vapours of acetone. Geometric accuracy and surface roughness are measured both before and after the chemical treatment to investigate the change in geometric accuracy, surface roughness of FDM parts. Findings The results indicate that surface roughness is reduced immensely after cold vapour treatment with minimum variation in geometric accuracy of parts. Parts build vertically over its side face (X orientation) provides the overall better surface finish and geometric accuracy. Originality/value The present study provides an approach of post-built treatment for FDM parts and observes a significant improvement in surface finish of the components. The present approach of post-built treatment can be adopted to enhance the surface quality as well as to achieve desired geometric accuracy for different primitive, freeform/curved surfaces of FDM samples suitable for functional components as well as prototypes.

Experimental investigation of FDM process for improvement of mechanical properties and production cost

2014 ◽  
Vol 20 (3) ◽  
pp. 228-235 ◽  
Author(s):  
Ismail Durgun ◽  
Rukiye Ertan
Keyword(s):  
Mechanical Properties ◽  
Surface Roughness ◽  
Production Cost ◽  
Fused Deposition Modelling ◽  
Content Type ◽  
Fused Deposition ◽  
Close Relationship ◽  
Raster Angle ◽  
Part Orientation ◽  
Selection Of

Purpose – The mechanical properties and surface finish of functional parts are important consideration in rapid prototyping, and the selection of proper parameters is essential to improve manufacturing solutions. The purpose of this paper is to describe how parts manufactured by fused deposition modelling (FDM), with different part orientations and raster angles, were examined experimentally and evaluated to achieve the desired properties of the parts while shortening the manufacturing times due to maintenance costs. Design/methodology/approach – For this purpose, five different raster angles (0°, 30°, 45°, 60° and 90°) for three part orientations (horizontal, vertical and perpendicular) have been manufactured by the FDM method and tested for surface roughness, tensile strength and flexural strength. Also, behaviour of the mechanical properties was clarified with scanning electron microscopy images of fracture surfaces. Findings – The research results suggest that the orientation has a more significant influence than the raster angle on the surface roughness and mechanical behaviour of the resulting fused deposition part. The results indicate that there is close relationship between the surface roughness and the mechanical properties. Originality/value – The results of this paper are useful in defining the most appropriate raster angle and part orientation in minimum production cost for FDM components on the basis of their expected in-service loading.

Multi-objective optimization of dimensional accuracy, surface roughness and hardness of hybrid investment cast components

2017 ◽  
Vol 23 (5) ◽  
pp. 845-857 ◽  
Author(s):  
Parlad Kumar Garg ◽  
Rupinder Singh ◽  
IPS Ahuja
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Surface Finish ◽  
Dimensional Accuracy ◽  
Multi Objective Optimization ◽  
Content Type ◽  
Multi Objective ◽  
Fused Deposition ◽  
Taguchi Design Of Experiments ◽  
Investment Cast

Purpose The purpose of this paper is to optimize the process parameters to obtain the best dimensional accuracy, surface finish and hardness of the castings produced by using fused deposition modeling (FDM)-based patterns in investment casting (IC). Design/methodology/approach In this paper, hip implants have been prepared by using plastic patterns in IC process. Taguchi design of experiments has been used to study the effect of six different input process parameters on the dimensional deviation, surface roughness and hardness of the implants. Analysis of variance has been used to find the effect of each input factor on the output. Multi-objective optimization has been done to find the combined best values of output. Findings The results proved that the FDM patterns can be used successfully in IC. A wax coating on the FDM patterns improves the surface finish and dimensional accuracy. The improved dimensional accuracy, surface finish and hardness have been achieved simultaneously through multi-objective optimization. Research limitations/implications A thin layer of wax is used on the plastic patterns. The effect of thickness of the layer has not been considered. Further research is needed to study the effect of the thickness of the wax layer. Practical implications The results obtained by the study would be helpful in making decisions regarding machining and/or coating on the parts produced by this process. Originality/value In this paper, multi-objective optimization of dimensional accuracy, surface roughness and hardness of hybrid investment cast components has been performed.

scholarly journals Parametric Effect on Surface Finish of Three-Dimensional Printed Object

2018 ◽  
Vol 3 (2) ◽  
pp. 98-104
Author(s):  
Muhammad Hasibul Hasan ◽  
Shugata Ahmed ◽  
Ron Voldman ◽  
Mirt Mehany
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Three Dimensional ◽  
Fused Deposition Modelling ◽  
Average Surface Roughness ◽  
Empty Shell ◽  
Average Surface ◽  
Fused Deposition ◽  
Resolution Parameter ◽  
Printing Processes

The ability to use different parameters and finishing techniques in fused deposition modelling (FDM) depends largely on part geometries, materials, printing processes like Z-resolution and post processing to some extent. Low quality poor surface finish due to layer ovality, improper Z-resolution parameter selection and fill of the empty shell in three-dimensional (3D) printing, results unexpected texture and appearance. An investigation is carried out on the effects of Z-resolution (0.15 mm to 0.40 mm) and Fill parameters on flat and curved surface objects manufactured using the FDM process. Moreover, post surface treatment was performed using acetone. It was found that average surface roughness increases with increasing Z-resolution. Solid Fill can create a smoother surface as oppose to Sparse Fill. Surface roughness improves significantly after post treatment with organic solvent acetone.

Experimental study of surface roughness, dimensional accuracy and time of fabrication of parts produced by fused deposition modelling

2020 ◽  
Vol 26 (9) ◽  
pp. 1535-1554
Author(s):  
Swapnil Vyavahare ◽  
Shailendra Kumar ◽  
Deepak Panghal
Keyword(s):  
Experimental Study ◽  
Surface Roughness ◽  
Layer Thickness ◽  
Process Parameters ◽  
Dimensional Accuracy ◽  
Fused Deposition Modelling ◽  
Content Type ◽  
Build Orientation ◽  
Fused Deposition ◽  
Significant Process

Purpose This paper aims to focus on an experimental study of surface roughness, dimensional accuracy and time of fabrication of parts produced by fused deposition modelling (FDM) technique of additive manufacturing. The fabricated parts of acrylonitrile butadiene styrene (ABS) material have pyramidal and conical features. Influence of five process parameters of FDM, namely, layer thickness, wall print speed, build orientation, wall thickness and extrusion temperature is studied on response characteristics. Furthermore, regression models for responses are developed and significant process parameters are optimized. Design/methodology/approach Comprehensive experimental study is performed using response surface methodology. Analysis of variance is used to investigate the influence of process parameters on surface roughness, dimensional accuracy and time of fabrication in both outer pyramidal and inner conical regions of part. Furthermore, a multi-response optimization using desirability function is performed to minimize surface roughness, improve dimensional accuracy and minimize time of fabrication of parts. Findings It is found that layer thickness and build orientation are significant process parameters for surface roughness of parts. Surface roughness increases with increase in layer thickness, while it decreases initially and then increases with increase in build orientation. Layer thickness, wall print speed and build orientation are significant process parameters for dimensional accuracy of FDM parts. For the time of fabrication, layer thickness and build orientation are found as significant process parameters. Based on the analysis, statistical non-linear quadratic models are developed to predict surface roughness, dimensional accuracy and time of fabrication. Optimization of process parameters is also performed using desirability function. Research limitations/implications The present study is restricted to the parts of ABS material with pyramidal and conical features only fabricated on FDM machine with delta configuration. Originality/value From the critical review of literature it is found that some researchers have made to study the influence of few process parameters on surface roughness, dimensional accuracy and time of fabrication of simple geometrical parts. Also, regression models and optimization of process parameters has been performed for simple parts. The present work is focussed on studying all these aspects in complicated geometrical parts with pyramidal and conical features.

scholarly journals Taguchi S/N and TOPSIS Based Optimization of Fused Deposition Modelling and Vapor Finishing Process for Manufacturing of ABS Plastic Parts

Materials ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5176
Author(s):  
Jasgurpreet Singh Chohan ◽  
Raman Kumar ◽  
TH Bhatia Singh ◽  
Sandeep Singh ◽  
Shubham Sharma ◽  
...  
Keyword(s):  
Surface Roughness ◽  
New Product Development ◽  
Surface Finish ◽  
Fused Deposition Modeling ◽  
Orientation Angle ◽  
Fused Deposition Modelling ◽  
Strength Increase ◽  
Major Barrier ◽  
Practical Applications ◽  
Fused Deposition

Despite several additive manufacturing techniques are commercially available in market, Fused Deposition Modeling (FDM) is increasingly used by researchers and engineers for new product development. FDM is an established process with a plethora of advantages, but the visible surface roughness (SR), being an intrinsic limitation, is major barrier against utilization of fabricated parts for practical applications. In the present study, the chemical finishing method, using vapour of acetone mixed with heated air, is being used. The combined impact of orientation angle, finishing temperature and finishing time has been studied using Taguchi and ANOVA, whereas multi-criteria optimization is performed using the Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS). The surface finish was highly responsive to increase in temperature while orientation angle of 0° yielded maximum strength; increase in finishing time led to weight gain of FDM parts. As the temperature increases, the percentage change in surface roughness increases as higher temperature assists the melt down process. On the other hand, anisotropic behaviour plays a major role during tensile testing. The Signal-to-noise (S/N) ratio plots, and ANOVA results indicated that surface finish is directly proportionate to finishing time because a longer exposure results in complete layer reflowing and settlement.

A multi-criteria decision making method for vapor smoothening fused deposition modelling part

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Sugavaneswarn M. ◽  
Prashanthi B. ◽  
John Rajan A.
Keyword(s):  
Decision Making ◽  
Surface Roughness ◽  
Process Parameters ◽  
Surface Finish ◽  
Orientation Angle ◽  
Multi Criteria Decision Making ◽  
Post Processing ◽  
Dimensional Error ◽  
Content Type ◽  
Fused Deposition

Purpose This paper aims to enhance the surface finish of the fused deposition modeling (FDM) part using the vapor smoothening (VS) post-processing method and to study the combined effect of FDM and VS process parameters on the quality of the part. Design/methodology/approach Analysis of variance method is used to understand the significance of the FDM and VS process parameters. Following this, the optimized parameter for multiple criteria response is reported using the technique for order preference by similarity to ideal solution. The process parameters alternatives are build orientation angle, build surface normal and exposure time and the criteria are surface roughness and dimensional error percentage. Findings The result observed contradicts the result reported on the independent parameter optimization of FDM and VS processes. There is a radical improvement in the surface finish on account of the coating process and an increase in the exposure time results in the decrease of the surface roughness. Minimum surface roughness of 0.11 µm is observed at 1,620 build angle and the least dimensional error of 0.01% is observed at build orientation angle 540. The impact of VS on the up-facing surface is different from the down-facing surface due to the removal of support material burrs and the exposure of the surface to vapor direction. Originality/value A study on the multi-criteria decision-making to ascertain the effect of post-processing on FDM component surface normal directed both to downward (build angle 0°–90°) and to upward (build angle 99°–180°) are reported for the first time in this article. The data reported for the post-processed FDM part at the build angle 0°–180° can be used as a guideline for selecting the optimal parameter and for assigning appropriate tolerance in the CAD model.

State of Art on Vapour Smoothing of Fused Deposition Modelling Components

2021 ◽  
Vol 903 ◽  
pp. 57-63
Author(s):  
S.M. Basha ◽  
M.M. Basha ◽  
N. Venkaiah ◽  
M.R. Shankar
Keyword(s):  
Surface Roughness ◽  
Lead Time ◽  
3D Model ◽  
Fused Deposition Modelling ◽  
Machining Processes ◽  
Fused Deposition ◽  
Staircase Effect ◽  
A New Technique ◽  
Time Required ◽  
Functional Components

Fused Deposition Modelling (FDM) is one of the additive manufacturing processes which can produce prototypes or functional components without the use of fixtures, and the lead time required is reduced drastically compared to traditional machining processes. The application of the FDM process in the biomedical and casting industries is limited by its poor surface roughness which is most generally caused by the staircase effect and chordal error of the 3D model. Owing to the drawbacks of mechanical based finishing techniques, researchers have come up with a new technique known as Vapour Smoothing (VS). In this work, past literature of the VS process of FDM components is reported and it has been seen that the VS process is giving a promising improvement in surface roughness of FDM components.

scholarly journals COMBINING FUSED DEPOSITION MODELLING WITH ABRASIVE MILLING TO ATTAIN HIGHER DIMENSIONAL ACCURACY AND BETTER SURFACE FINISH ON THE FINISHED PRODUCT

2018 ◽  
Vol 19 (2) ◽  
pp. 221-231 ◽  
Author(s):  
A N M AMANULLAH TOMAL ◽  
Tanveer Saleh ◽  
Md. Raisuddin Khan
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Three Dimensional ◽  
Dimensional Accuracy ◽  
Cnc Machining ◽  
Numerical Control ◽  
Fused Deposition Modelling ◽  
Numerical Control Machining ◽  
Fused Deposition ◽  
Higher Dimensional

ABSTRACT: Currently, two manufacturing methods, namely CNC (Computer Numerical Control) machining and rapid prototyping (RP), are widely used to produce final products and prototypes.  Both the processes have their own advantages. CNC machining such as milling and grinding (subtractive method) can fabricate parts with higher precision and accuracy. On the other hand, RP (additive method), can manufacture parts with complicated 3-D (three dimensional) features, which ensures effective material usage. However, RP produced parts lack accuracy and smooth surface finish. In this research, we are aiming to achieve on-machine mechanical post-processing of 3-D printed (using Fused Deposition Modelling, a kind of RP process) parts to achieve higher dimensional accuracy and better surface roughness. To achieve the goal, we developed a new hybrid system to assimilate both of these processes. There are, however, two vital considerations needed to be taken into account for integrating the two processes. The first concern is the integration of dissimilar control systems for two processes and the second aspect is maintaining the tools’ (milling spindle and the heat extruder) setup accuracy during the changeover step. The developed hybrid machine has been tested with experimentations and the result showed that the dimensional accuracy was improved by 71% to 99% when the FDM part was compared with the final part after abrasive milling operation. At the same time, average surface roughness (Ra) was improved up to 91.3%. Further, we found that low layer thickness improves the product quality. The proposed system could push the conventional FDM system to the next level to attain better quality of final products. ABSTRAK: Dua kaedah terkini proses pembuatan, dinamakan mesin Kawalan Komputer Bernombor (CNC) dan prototaip langsung (RP) telah digunakan secara meluas bagi menghasilkan produk dan prototaip. Kedua-dua proses mempunyai keistimewaan tersendiri. Mesin CNC seperti mesin penghasil permukaan dan mesin penebuk lubang (melalui kaedah pengurangan) dapat menghasilkan sesuatu bahagian dengan ketepatan tinggi. Pada sudut lain, RP (melalui kaedah penambahan), dapat menghasilkan bahagian dengan kaedah 3D (tiga dimensi) yang rumit tetapi berkesan dalam memaksimakan penggunaan material. Walau bagaimanapun, penghasilan bahagian melalui kaedah RP mempunyai kekurangan pada ketepatan dan kekurangan pada kekemasan permukaan akhir. Kajian ini bertujuan meraih ketepatan dimensi yang lebih tinggi dan kekemasan permukaan yang lebih bagus pada proses terakhir pada bahagian cetakan mesin mekanikal 3D (menggunakan Model Deposit Fuse iaitu salah satu proses RP). Bagi mencapai tujuan ini, kami menghasilkan sistem hibrid terbaru untuk mengasimulasi kedua-dua proses. Walau bagaimanapun, terdapat dua perkara penting perlu diambil kira untuk diintegrasi bersama kedua-dua proses. Penilaian pertama adalah pada sistem kawalan tidak serupa, dan kedua pada aspek pengekalan alat (gelendung pemutar dan kepanasan pembentuk) ketepatan penyediaan semasa peringkat perubahan. Mesin hibrid yang dicipta telah diuji melalui eksperimentasi dan keputusan menunjukkan ketepatan dimensi telah bertambah daripada 71% kepada 99% semasa bahagian FDM dibandingkan dengan bahagian akhir selepas operasi putaran kasar. Pada masa sama, purata permukaan kasar (Ra) telah bertambah kepada 91.3%. Kami juga mendapati ketebalan lapisan bawah telah menambah baik kualiti produk. Sistem yang dicadangkan dapat mengubah sistem FDM konvensional kepada peringkat lebih tinggi bagi memperolehi kualiti terbaik pada produk akhir.

Investigations for improving the surface finish of FDM based ABS replicas by chemical vapor smoothing process: a case study

2017 ◽  
Vol 37 (1) ◽  
pp. 13-21 ◽  
Author(s):  
Jaspreet Singh ◽  
Rupinder Singh ◽  
Harwinder Singh
Keyword(s):  
Process Parameters ◽  
Surface Finish ◽  
Research Work ◽  
Chemical Vapor ◽  
Fused Deposition Modelling ◽  
Post Processing ◽  
Processing Stage ◽  
Content Type ◽  
Fused Deposition

Purpose This research work aims to make an effort to investigate the effect of fused deposition modelling (FDM) process parameters on the surface finish of acrylonitrile butadiene styrene (ABS) replicas (as pre-processing stage), followed by chemical vapor smoothing (CVS) process (as a post-processing stage) as a case study. Design/methodology/approach The Taguchi L18 orthogonal array has been used for optimizing process parameters of FDM and CVS processes. Findings This study highlights that orientation and part density, and the interaction between these two have a significant effect on the surface finish at the pre-processing stage of FDM. However, after post-processing with CVS, there is hardly any influence of pre-processing FDM parameters. Originality/value The study highlights that for improving the productivity of the FDM process, the parametric optimization of process may be made on the basis of production cost and time in place of surface finish of ABS replicas. The results obtained have been verified by performing the confirmation experiments.

Animal orthosis fabrication with additive manufacturing – a case study of custom orthosis for chicken

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Wiktoria Maria Wojnarowska ◽  
Jakub Najowicz ◽  
Tomasz Piecuch ◽  
Michał Sochacki ◽  
Dawid Pijanka ◽  
...  
Keyword(s):  
Veterinary Medicine ◽  
Additive Manufacturing ◽  
Computer Aided Design ◽  
Three Dimensional ◽  
Fused Deposition Modelling ◽  
Content Type ◽  
Fused Deposition ◽  
Secondary Objective ◽  
Traditional Manufacturing ◽  
Aided Design

Purpose Chicken orthoses that cover the ankle joint area are not commercially available. Therefore, the main purpose of this study is to fabricate a customised temporary Ankle–Foot Orthosis (AFO) for a chicken with a twisted ankle using computer-aided design (CAD) and three-dimensional (3D) printing. The secondary objective of the paper is to present the specific application of Additive Manufacturing (AM) in veterinary medicine. Design/methodology/approach The design process was based on multiple sketches, photos and measurements that were provided by the owner of the animal. The 3D model of the orthosis was made with Autodesk Fusion 360, while the prototype was fabricated using fused deposition modelling (FDM). Evaluation of the AFO was performed using the finite element method. Findings The work resulted in a functional 3D printed AFO for chicken. It was found that the orthosis made with AM provides satisfactory stiffen and a good fit. It was concluded that AM is suitable for custom bird AFO fabrication and, in some respects, is superior to traditional manufacturing methods. It was also concluded that the presented procedure can be applied in other veterinary cases and to other animal species and other parts of their body. AM provides veterinary with a powerful tool for the production of well-fitted and durable orthoses for animals. Research limitations/implications The study does not include the chicken's opinion on the comfort or fit of the manufactured AFO due to communication issues. Evaluation of the final prototype was done by the researchers and the animal owner. Originality/value No evidence was found in the literature on the use of AM for chicken orthosis, so this study is the first to describe such an application of AM. In addition, the study demonstrates the value of AM in veterinary medicine, especially in the production of devices such as orthoses.

Sign in / Sign up

Export Citation Format

Share Document