3D printing of clay paste enhanced by scrap polymer from powder bed processes

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Mattia Mele ◽  
Michele Ricciarelli ◽  
Giampaolo Campana
Keyword(s):  
Additive Manufacturing ◽  
Volumetric Flow Rate ◽  
The Body ◽  
Fused Deposition Modelling ◽  
Powder Bed Fusion ◽  
Dimensional Error ◽  
Content Type ◽  
Powder Bed ◽  
Fused Deposition ◽  
Polymer Fraction

Purpose Powder bed additive manufacturing processes are widespread due to their many technical and economic advantages. Nevertheless, the disposal of leftover powder poses a problem in terms of process sustainability. The purpose of this paper is to provide an alternative solution to recycle waste PA12 powder from HP multi jet fusion. In particular, the opportunity to use this material as a dispersion in three-dimensional (3D) printed clay is investigated. Design/methodology/approach A commercial fused deposition modelling printer was re-adapted to extrude a viscous paste composed of clay, PA12 and water. Once printed, parts were dried and then put in an oven to melt the polymer fraction. Four compositions with different PA12 concentration were studied. First, the extrudability of the paste was observed by testing different extrusion lengths. Then, the surface porosities were evaluated through microscopical observations of the manufactured parts. Finally, benchmarks with different geometries were digitalised via 3D scanning to analyse the dimensional alterations arising at each stage of the process. Findings Overall, the feasibility of the process is demonstrated. Extrusion tests revealed that the composition of the paste has a minor influence on the volumetric flow rate, exhibiting a better consistency in the case of long extrusions. The percentage of surface cavities was proportional to the polymer fraction contained in the mix. From dimensional analyses, it was possible to conclude that PA12 reduced the degree of shrinkage during the drying phase, while it increased dimensional alterations occurring in the melting phase. The results showed that the dimensional error measured on the z-axis was always higher than that of the XY plane. Practical implications The method proposed in this paper provides an alternative approach to reuse leftover powders from powder bed fusion processes via another additive manufacturing process. This offers an affordable and open-source solution to companies dealing with polymer powder bed fusion, allowing them to reduce their environmental impacts while expanding their production. Originality/value The paper presents an innovative additive manufacturing solution for powder reuse. Unlike the recycling methods in the body of literature, this solution does not require any intermediate transformation process, such as filament fabrication. Also, the cold material deposition enables the adoption of very inexpensive extrusion equipment. This preliminary study demonstrates the feasibility and the benefits of this process, paving the way for numerous future studies.

Animal orthosis fabrication with additive manufacturing – a case study of custom orthosis for chicken

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Wiktoria Maria Wojnarowska ◽  
Jakub Najowicz ◽  
Tomasz Piecuch ◽  
Michał Sochacki ◽  
Dawid Pijanka ◽  
...  
Keyword(s):  
Veterinary Medicine ◽  
Additive Manufacturing ◽  
Computer Aided Design ◽  
Three Dimensional ◽  
Fused Deposition Modelling ◽  
Content Type ◽  
Fused Deposition ◽  
Secondary Objective ◽  
Traditional Manufacturing ◽  
Aided Design

Purpose Chicken orthoses that cover the ankle joint area are not commercially available. Therefore, the main purpose of this study is to fabricate a customised temporary Ankle–Foot Orthosis (AFO) for a chicken with a twisted ankle using computer-aided design (CAD) and three-dimensional (3D) printing. The secondary objective of the paper is to present the specific application of Additive Manufacturing (AM) in veterinary medicine. Design/methodology/approach The design process was based on multiple sketches, photos and measurements that were provided by the owner of the animal. The 3D model of the orthosis was made with Autodesk Fusion 360, while the prototype was fabricated using fused deposition modelling (FDM). Evaluation of the AFO was performed using the finite element method. Findings The work resulted in a functional 3D printed AFO for chicken. It was found that the orthosis made with AM provides satisfactory stiffen and a good fit. It was concluded that AM is suitable for custom bird AFO fabrication and, in some respects, is superior to traditional manufacturing methods. It was also concluded that the presented procedure can be applied in other veterinary cases and to other animal species and other parts of their body. AM provides veterinary with a powerful tool for the production of well-fitted and durable orthoses for animals. Research limitations/implications The study does not include the chicken's opinion on the comfort or fit of the manufactured AFO due to communication issues. Evaluation of the final prototype was done by the researchers and the animal owner. Originality/value No evidence was found in the literature on the use of AM for chicken orthosis, so this study is the first to describe such an application of AM. In addition, the study demonstrates the value of AM in veterinary medicine, especially in the production of devices such as orthoses.

A printability assessment framework for fabricating low variability nickel-niobium parts using laser powder bed fusion additive manufacturing

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Bing Zhang ◽  
Raiyan Seede ◽  
Austin Whitt ◽  
David Shoukr ◽  
Xueqin Huang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Uncertainty Quantification ◽  
Process Optimization ◽  
Powder Bed Fusion ◽  
Assessment Framework ◽  
Laser Powder Bed Fusion ◽  
Content Type ◽  
Powder Bed ◽  
Analytical Thermal Model

Purpose There is recent emphasis on designing new materials and alloys specifically for metal additive manufacturing (AM) processes, in contrast to AM of existing alloys that were developed for other traditional manufacturing methods involving considerably different physics. Process optimization to determine processing recipes for newly developed materials is expensive and time-consuming. The purpose of the current work is to use a systematic printability assessment framework developed by the co-authors to determine windows of processing parameters to print defect-free parts from a binary nickel-niobium alloy (NiNb5) using laser powder bed fusion (LPBF) metal AM. Design/methodology/approach The printability assessment framework integrates analytical thermal modeling, uncertainty quantification and experimental characterization to determine processing windows for NiNb5 in an accelerated fashion. Test coupons and mechanical test samples were fabricated on a ProX 200 commercial LPBF system. A series of density, microstructure and mechanical property characterization was conducted to validate the proposed framework. Findings Near fully-dense parts with more than 99% density were successfully printed using the proposed framework. Furthermore, the mechanical properties of as-printed parts showed low variability, good tensile strength of up to 662 MPa and tensile ductility 51% higher than what has been reported in the literature. Originality/value Although many literature studies investigate process optimization for metal AM, there is a lack of a systematic printability assessment framework to determine manufacturing process parameters for newly designed AM materials in an accelerated fashion. Moreover, the majority of existing process optimization approaches involve either time- and cost-intensive experimental campaigns or require the use of proprietary computational materials codes. Through the use of a readily accessible analytical thermal model coupled with statistical calibration and uncertainty quantification techniques, the proposed framework achieves both efficiency and accessibility to the user. Furthermore, this study demonstrates that following this framework results in printed parts with low degrees of variability in their mechanical properties.

Modeling and analysis of the on-demand spare parts supply using additive manufacturing

2019 ◽  
Vol 25 (3) ◽  
pp. 473-487 ◽  
Author(s):  
Yuan Zhang ◽  
Stefan Jedeck ◽  
Li Yang ◽  
Lihui Bai
Keyword(s):  
Supply Chain ◽  
Additive Manufacturing ◽  
Spare Parts ◽  
Production Optimization ◽  
Arrival Process ◽  
Powder Bed Fusion ◽  
Content Type ◽  
Modeling And Analysis ◽  
Powder Bed ◽  
On Demand

PurposeDespite the widespread expectation that additive manufacturing (AM) will become a disruptive technology to transform the spare parts supply chain, very limited research has been devoted to the quantitative modeling and analysis on how AM could fulfill the on-demand spare parts supply. On the other hand, the choice of using AM as a spare parts supply strategy over traditional inventory is a rising decision faced by manufacturers and requires quantitative analysis for their AM-or-stock decisions. The purpose of this paper is to develop a quantitative performance model for a generic powder bed fusion AM system in a spare parts supply chain, thus providing insights into this less-explored area in the literature.Design/methodology/approachIn this study, analysis based on a discrete event simulation was carried out for the use of AM in replacement of traditional warehouse inventory for an on-demand spare parts supply system. Generic powder bed fusion AM system was used in the model, and the same modeling approach could be applied to other types of AM processes. Using this model, the impact of both spare parts demand characteristics (e.g. part size attributes, demand rates) and the AM operations characteristics (e.g. machine size and postpone strategy) on the performance of using AM to supply spare parts was studied.FindingsThe simulation results show that in many cases the AM operation is not as cost competitive compared to the traditional warehouse-based spare parts supply operation, and that the spare parts size characteristics could significantly affect the overall performance of the AM operations. For some scenarios of the arrival process of spare parts demand, the use of the batched AM production could potentially result in significant delay in parts delivery, which necessitates further investigations of production optimization strategies.Originality/valueThe findings demonstrate that the proposed simulation tool can not only provide insights on the performance characteristics of using AM in the spare parts supply chain, especially in comparison to the traditional warehousing system, but also can be used toward decision making for both the AM manufacturers and the spare parts service providers.

A review on advancements in applications of fused deposition modelling process

2020 ◽  
Vol 26 (4) ◽  
pp. 669-687 ◽  
Author(s):  
Sathies T. ◽  
Senthil P. ◽  
Anoop M.S.
Keyword(s):  
Additive Manufacturing ◽  
Research Work ◽  
Rapid Tooling ◽  
Future Research ◽  
Fused Deposition Modelling ◽  
Content Type ◽  
Fused Deposition ◽  
Low Volume ◽  
Customized Products

Purpose Fabrication of customized products in low volume through conventional manufacturing incurs a high cost, longer processing time and huge material waste. Hence, the concept of additive manufacturing (AM) comes into existence and fused deposition modelling (FDM), is at the forefront of researches related to polymer-based additive manufacturing. The purpose of this paper is to summarize the research works carried on the applications of FDM. Design/methodology/approach In the present paper, an extensive review has been performed related to major application areas (such as a sensor, shielding, scaffolding, drug delivery devices, microfluidic devices, rapid tooling, four-dimensional printing, automotive and aerospace, prosthetics and orthosis, fashion and architecture) where FDM has been tested. Finally, a roadmap for future research work in the FDM application has been discussed. As an example for future research scope, a case study on the usage of FDM printed ABS-carbon black composite for solvent sensing is demonstrated. Findings The printability of composite filament through FDM enhanced its application range. Sensors developed using FDM incurs a low cost and produces a result comparable to those conventional techniques. EMI shielding manufactured by FDM is light and non-oxidative. Biodegradable and biocompatible scaffolds of complex shapes are possible to manufacture by FDM. Further, FDM enables the fabrication of on-demand and customized prosthetics and orthosis. Tooling time and cost involved in the manufacturing of low volume customized products are reduced by FDM based rapid tooling technique. Results of the solvent sensing case study indicate that three-dimensional printed conductive polymer composites can sense different solvents. The sensors with a lower thickness (0.6 mm) exhibit better sensitivity. Originality/value This paper outlines the capabilities of FDM and provides information to the user about the different applications possible with FDM.

scholarly journals Laser powder bed fusion additive manufacturing of copper wicking structures: fabrication and capillary characterization

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Adnen Mezghani ◽  
Abdalla R. Nassar ◽  
Corey J. Dickman ◽  
Eduardo Valdes ◽  
Raul Alvarado
Keyword(s):  
Additive Manufacturing ◽  
Design Methodology ◽  
Heat Pipes ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Content Type ◽  
Powder Bed ◽  
Published Report ◽  
Secondary Manufacturing ◽  
Design Freedom

Purpose An integral component in heat pipes (HPs) and vapor chambers (VCs) is a porous wicking structure. Traditional methods for manufacturing wicking structures within HPs and VCs involve secondary manufacturing processes and are generally limited to simple geometries. This work aims to leverage the unprecedented level of design freedom of laser powder bed fusion (LPBF) additive manufacturing (AM) to produce integrated wicking structures for HPs and VCs. Design/methodology/approach Copper wicking structures are fabricated through LPBF via partial sintering and via the formation of square, hexagonal and rectangular arrangements of micro-pins and micro-grooves, produced in multiple build directions. Wicks are characterized by conducting capillary performance analysis through the measurement of porosity, permeability and capillary rate-of-rise. Findings Copper wicking structures were successfully fabricated with capillary performance, K/reff, ranging from 0.186–1.74 µm. The rectangular-arrangement micro-pin wick presented the highest performance. Originality/value This work represents the first published report on LPBF AM of copper wicking structures for HPs/VCs applications and represents foundational knowledge for fabricating complete assemblies of copper VCs and HPs through LPBF AM.

Development and experimental study of an automated laser-foil-printing additive manufacturing system

2022 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Chia-Hung Hung ◽  
Tunay Turk ◽  
M. Hossein Sehhat ◽  
Ming C. Leu
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Additive Manufacturing ◽  
Mechanical Strength ◽  
Automated System ◽  
304L Stainless Steel ◽  
Powder Bed Fusion ◽  
Content Type ◽  
Powder Bed ◽  
Manufacturing Methods

Purpose This paper aims to present the development and experimental study of a fully automated system using a novel laser additive manufacturing technology called laser foil printing (LFP), to fabricate metal parts layer by layer. The mechanical properties of parts fabricated with this novel system are compared with those of comparable methodologies to emphasize the suitability of this process. Design/methodology/approach Test specimens and parts with different geometries were fabricated from 304L stainless steel foil using an automated LFP system. The dimensions of the fabricated parts were measured, and the mechanical properties of the test specimens were characterized in terms of mechanical strength and elongation. Findings The properties of parts fabricated with the automated LFP system were compared with those of parts fabricated with the powder bed fusion additive manufacturing methods. The mechanical strength is higher than those of parts fabricated by the laser powder bed fusion and directed energy deposition technologies. Originality/value To the best knowledge of authors, this is the first time a fully automated LFP system has been developed and the properties of its fabricated parts were compared with other additive manufacturing methods for evaluation.

Effect of post-processing on microstructure and mechanical properties of Alloy 718 fabricated using powder bed fusion additive manufacturing processes

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Sareh Götelid ◽  
Taoran Ma ◽  
Christophe Lyphout ◽  
Jesper Vang ◽  
Emil Stålnacke ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Residual Stresses ◽  
Design Methodology ◽  
Hot Isostatic Pressing ◽  
Powder Bed Fusion ◽  
Content Type ◽  
Powder Bed ◽  
Nickel Based Superalloy ◽  
Compressive Stresses

Purpose This study aims to investigate additive manufacturing of nickel-based superalloy IN718 made by powder bed fusion processes: powder bed fusion laser beam (PBF-LB) and powder bed fusion electron beam (PBF-EB). Design/methodology/approach This work has focused on the influence of building methods and post-fabrication processes on the final part properties, including microstructure, surface quality, residual stresses and mechanical properties. Findings PBF-LB produced a much smoother surface. Blasting and shot peening (SP) reduced the roughness even more but did not affect the PBF-EB surface finish as much. As-printed PBF-EB parts have low residual stresses in all directions, whereas it was much higher for PBF-LB. However, heat treatment removed the stresses and SP created compressive stresses for samples from both PBF processes. The standard Arcam process parameter for PBF-EB for IN718 is not fully optimized, which leads to porosity and inferior mechanical properties. However, impact toughness after hot isostatic pressing was surprisingly high. Originality/value The two processes gave different results and also responses to post-treatments, which could be of advantage or disadvantage for different applications. Suggestions for improving the properties of parts produced by each method are presented.

scholarly journals Comparing additive manufacturing technologies for customised wrist splints

2015 ◽  
Vol 21 (3) ◽  
pp. 230-243 ◽  
Author(s):  
Abby Megan Paterson ◽  
Richard Bibb ◽  
R. Ian Campbell ◽  
Guy Bingham
Keyword(s):  
Additive Manufacturing ◽  
Upper Extremity ◽  
Digital Design ◽  
Future Research ◽  
Fused Deposition Modelling ◽  
Full Potential ◽  
Content Type ◽  
Fused Deposition ◽  
Am Processes ◽  
Design For Am

Purpose – The purpose of this paper is to compare four different additive manufacturing (AM) processes to assess their suitability in the context of upper extremity splinting. Design/methodology/approach – This paper describes the design characteristics and subsequent fabrication of six different wrist splints using four different AM processes: laser sintering (LS), fused deposition modelling (FDM), stereolithography (SLA) and polyjet material jetting via Objet Connex. The suitability of each process was then compared against competing designs and processes from traditional splinting. The splints were created using a digital design workflow that combined recognised clinical best practice with design for AM principles. Findings – Research concluded that, based on currently available technology, FDM was considered the least suitable AM process for upper extremity splinting. LS, SLA and material jetting show promise for future applications, but further research and development into AM processes, materials and splint design optimisation is required if the full potential is to be realised. Originality/value – Unlike previous work that has applied AM processes to replicate traditional splint designs, the splints described are based on a digital design for AM workflow, incorporating novel features and physical properties not previously possible in clinical splinting. The benefits of AM for customised splint fabrication have been summarised. A range of AM processes have also been evaluated for splinting, exposing the limitations of existing technology, demonstrating novel and advantageous design features and opportunities for future research.

scholarly journals Impact of additive manufacturing on engineering education – evidence from Italy

2015 ◽  
Vol 21 (5) ◽  
pp. 535-555 ◽  
Author(s):  
Paolo Minetola ◽  
Luca Iuliano ◽  
Elena Bassoli ◽  
Andrea Gatto
Keyword(s):  
Additive Manufacturing ◽  
Product Design ◽  
Mechanical Engineering ◽  
Additive Technologies ◽  
Direct Access ◽  
Fused Deposition Modelling ◽  
Content Type ◽  
Entry Level ◽  
Fused Deposition ◽  
The Impact

Purpose – The purpose of this paper is to evaluate how the direct access to additive manufacturing (AM) systems impacts on education of future mechanical engineers, within a Master’s program at a top Italian University. Design/methodology/approach – A survey is specifically designed to assess the relevance of entry-level AM within the learning environment, as a tool for project development. The survey is distributed anonymously to three consecutive cohorts of students who attended the course of “computer-aided production (CAP)”, within the Master of Science Degree in Mechanical Engineering at Politecnico di Torino. The course includes a practical project, consisting in the design of a polymeric product with multiple components and ending with the production of an assembled prototype. The working assembly is fabricated by the students themselves, who operate a fused deposition modelling (FDM) machine, finish the parts and evaluate assemblability and functionality. The post-course survey covers diverse aspects of the learning process, such as: motivation, knowledge acquisition, new abilities and team-working skills. Responses are analyzed to evaluate students’ perception of the usefulness of additive technologies in learning product design and development. Among the projects, one representative case study is selected and discussed. Findings – Results of the research affirm a positive relationship of access to AM devices to perceived interest, motivation and ease of learning of mechanical engineering. Entry-level additive technologies offer a hands-on experience within academia, fostering the acquisition of technical knowledge. Research limitations/implications – The survey is distributed to more than 200 students to cover the full population of the CAP course over three academic years. The year the students participated in the CAP course is not tracked because the instructor was the same and there were no administrative differences. For this reason, the survey administration might be a limitation of the current study. In addition to this, no gender distinction is made because historically, the percentage of female students in Mechanical Engineering courses is about 10 per cent or lower. Although the answers to the survey are anonymous, only 37 per cent of the students gave a feedback. Thus, on the one hand, impact assessment is limited to a sample of about one-third of the complete population, but, on the other hand, the anonymity ensures randomization in the sample selection. Practical implications – Early exposure of forthcoming designers to AM tools can turn into a “think-additive” approach to product design, that is a groundbreaking conception of geometries and product functionalities, leading to the full exploitation of the possibilities offered by additive technologies. Social implications – Shared knowledge can act as a springboard for mass adoption of AM processes. Originality/value – The advantages of adopting AM technologies at different levels of education, for diverse educational purposes and disciplines, are well assessed in the literature. The innovative aspect of this paper is that the impact of AM is evaluated through a feedback coming directly from mechanical engineering students.

Optimising the FDM additive manufacturing process to achieve maximum tensile strength: a state-of-the-art review

2019 ◽  
Vol 25 (6) ◽  
pp. 953-971 ◽  
Author(s):  
Tessa Jane Gordelier ◽  
Philipp Rudolf Thies ◽  
Louis Turner ◽  
Lars Johanning
Keyword(s):  
Tensile Strength ◽  
Additive Manufacturing ◽  
Material Selection ◽  
Single Point ◽  
Air Gap ◽  
Fused Deposition Modelling ◽  
Content Type ◽  
Maximum Tensile Strength ◽  
Fused Deposition ◽  
Raster Angle

Purpose Additive manufacturing or “3D printing” is a rapidly expanding sector and is moving from a prototyping service to a manufacturing service in its own right. With a significant increase in sales, fused deposition modelling (FDM) printers are now the most prevalent 3D printer on the market. The increase in commercial manufacturing necessitates an improved understanding of how to optimise the FDM printing process for various product mechanical properties. This paper aims to identify optimum print parameters for the FDM process to achieve maximum tensile strength through a review of recent studies in this field. Design/methodology/approach The effect of the governing printing parameters on the tensile strength of printed samples will be considered, including material selection, print orientation, raster angle, air gap and layer height. Findings The key findings include material recommendations, such as the use of emerging print materials like polyether-ether-ketone (PEEK), to produce samples with tensile strength over 200 per cent that of conventional materials such as acrylonitrile butadiene styrene (ABS). Amongst other parameters, it is shown that printing in the “upright” orientation should be avoided (samples can be up to 50 per cent weaker in this orientation) and air gap and raster width should be concurrently optimised to ensure good “inter-raster” bonding. The optimal choice of raster angle depends on print material; in ABS for example, selecting a 0° raster angle over a 90° angle can increase tensile strength by up to 100 per cent. Originality/value The paper conclusions provide researchers and practitioners with an up-to-date, single point reference, highlighting a series of robust recommendations to optimise the tensile strength of FDM-printed samples. Improving the mechanical performance of FDM-printed samples will support the continued growth of this technology as a viable production technique.

Sign in / Sign up

Export Citation Format

Share Document