Low-cost mobile system for multispectral cultural heritage data acquisition

2013 ◽  
Author(s):  
Jan Blazek ◽  
Jindrich Soukup ◽  
Barbara Zitova ◽  
Jan Flusser ◽  
Tomas Tichy ◽  
...  
Keyword(s):  
Cultural Heritage ◽  
Data Acquisition ◽  
Low Cost ◽  
Mobile System

A real time, wireless and low cost data acquisition system for residential PV modules

2020 ◽  
Author(s):  
Cheyma BARKA ◽  
Hanen MESSAOUDI-ABID ◽  
Houda BEN ATTIA SETTHOM ◽  
Afef BENNANI-BEN ABDELGHANI ◽  
Ilhem SLAMA-BELKHODJA ◽  
...  
Keyword(s):  
Data Acquisition ◽  
Real Time ◽  
Low Cost ◽  
Data Acquisition System ◽  
Cost Data ◽  
Acquisition System ◽  
Pv Modules

scholarly journals Comparative Analysis of Digital Models of Objects of Cultural Heritage Obtained by the “3D SLS” and “SfM” Methods

2021 ◽  
Vol 11 (12) ◽  
pp. 5321
Author(s):  
Marcin Barszcz ◽  
Jerzy Montusiewicz ◽  
Magdalena Paśnikowska-Łukaszuk ◽  
Anna Sałamacha
Keyword(s):  
Cultural Heritage ◽  
Low Cost ◽  
Three Dimensional ◽  
3D Models ◽  
Silk Road ◽  
Digital Models ◽  
Global Pandemic ◽  
University Of Technology ◽  
Three Dimensional Models ◽  
3D Digitisation

In the era of the global pandemic caused by the COVID-19 virus, 3D digitisation of selected museum artefacts is becoming more and more frequent practice, but the vast majority is performed by specialised teams. The paper presents the results of comparative studies of 3D digital models of the same museum artefacts from the Silk Road area generated by two completely different technologies: Structure from Motion (SfM)—a method belonging to the so-called low-cost technologies—and by Structured-light 3D Scanning (3D SLS). Moreover, procedural differences in data acquisition and their processing to generate three-dimensional models are presented. Models built using a point cloud were created from data collected in the Afrasiyab museum in Samarkand (Uzbekistan) during “The 1st Scientific Expedition of the Lublin University of Technology to Central Asia” in 2017. Photos for creating 3D models in SfM technology were taken during a virtual expedition carried out under the “3D Digital Silk Road” program in 2021. The obtained results show that the quality of the 3D models generated with SfM differs from the models from the technology (3D SLS), but they may be placed in the galleries of the vitrual museum. The obtained models from SfM do not have information about their size, which means that they are not fully suitable for archiving purposes of cultural heritage, unlike the models from SLS.

scholarly journals A Low-cost System for High-frequency Solar Imagery and Power Data Acquisition

2021 ◽  
Vol 1826 (1) ◽  
pp. 012082
Author(s):  
G F Bassous ◽  
R F Calili ◽  
C R H Barbosa
Keyword(s):  
Data Acquisition ◽  
High Frequency ◽  
Low Cost ◽  
Cost System

Development of Appropriate Power Distribution Design for Can-Sized satellite (canSAT)

2021 ◽  
Vol 02 (02) ◽  
Author(s):  
Devina Cristine Marubin ◽  
◽  
Sim Sy Yi ◽  
Keyword(s):  
Power System ◽  
Data Acquisition ◽  
Power Supply ◽  
Communication System ◽  
Power Distribution ◽  
Low Cost ◽  
Small Satellite ◽  
Power Budget ◽  
Space Agency ◽  
Rules Set

Can-Sized satellite (canSAT) is a small satellite that is used for educational purpose. CanSAT offer student to build their satellites with their creativity which make the learning process more effective. In Malaysia, SiswaSAT is held by the Malaysia Space Agency for students in different categories to participate and build their satellites according to rules set and it should be a low-cost project. CanSAT can be divided into few parts which are communication system, onboard data acquisition, ground control station and power system. The power system is one of the important and heaviest subsystems, it needed to supply power, but weight and size are one of the main concerned as the canSAT should not exceed the required weight and selecting power supply that is matched with the overall power budget that has small size and lightweight is challenging. Therefore, the power supply selection should consider this detail. The power distribution design should be able to supply an appropriate amount of current and voltage to the components according to their specification. This study aims to develop and test the proposed prototype which is named ScoreSAT able to provide data and have enough power supply for the whole operation. Therefore, an initiative to develop the appropriate power distribution design for canSAT is taken to overcome the problem of the power system. Moreover, each subsystem needs to be tested by obtaining the results from the onboard data acquisition and transmit the data using the communication system before integrating into the power system. ScoreSAT prototype needs to carry the system that is mounted inside, thus the space inside the prototype needs to be fully utilized for the whole system to fit in. ScoreSAT completes the mission by obtaining data acquisition during the operation.

scholarly journals Design and Development of a 5-Channel Arduino-Based Data Acquisition System (ABDAS) for Experimental Aerodynamics Research

Sensors ◽  
2018 ◽  
Vol 18 (7) ◽  
pp. 2382 ◽  
Author(s):  
Antonio Vidal-Pardo ◽  
Santiago Pindado
Keyword(s):  
Data Acquisition ◽  
Low Cost ◽  
Data Acquisition System ◽  
High Accuracy ◽  
Acquisition System ◽  
Calibration System ◽  
Experimental Aerodynamics ◽  
Accuracy Level ◽  
The Fourier Transform ◽  
Cup Anemometer

In this work, a new and low-cost Arduino-Based Data Acquisition System (ABDAS) for use in an aerodynamics lab is developed. Its design is simple and reliable. The accuracy of the system has been checked by being directly compared with a commercial and high accuracy level hardware from National Instruments. Furthermore, ABDAS has been compared to the accredited calibration system in the IDR/UPM Institute, its measurements during this testing campaign being used to analyzed two different cup anemometer frequency determination procedures: counting pulses and the Fourier transform. The results indicate a more accurate transfer function of the cup anemometers when counting pulses procedure is used.

The Designing of Data Acquisition Card through PIC18F4550 and an Interface Study

2015 ◽  
Vol 752-753 ◽  
pp. 1191-1197
Author(s):  
Hakan Terzioğlu ◽  
Saadetdin Herdem ◽  
Güngör Bal
Keyword(s):  
Data Acquisition ◽  
Low Cost ◽  
Computer Interface ◽  
Application System ◽  
Microsoft Access ◽  
Oscilloscope Screen ◽  
Data Acquisition Card ◽  
Interface Screen ◽  
Access Program ◽  
Interface Study

Since automatic control is used in every field, there is almost no industrial application system which doesn’t employ the sensors. It makes correctly reading the data obtained from sensors in the system with sensors and transmitting this data into the computer more important. In this executed study, a design for an interface which can be easily used with a low cost data processing card and with flexible structure was performed. In the executed system, the PIC18F4550 microcontroller was used and data can be accurately read from 10 different channels. The data read from the designed data acquisition card was transferred into a computer interface program prepared in C# program using a USB and recorded into the database in the Microsoft Access program. The designed interface, the values of read signals and their graphs may be displayed on the screen. Thus, the interface screen may be used as both an indicator and oscilloscope screen.

scholarly journals An Application of Integrated 3D Technologies for Replicas in Cultural Heritage

2019 ◽  
Vol 8 (6) ◽  
pp. 285 ◽  
Author(s):  
Balletti ◽  
Ballarin
Keyword(s):  
3D Printing ◽  
Cultural Heritage ◽  
Laser Scanning ◽  
Low Cost ◽  
Three Dimensional ◽  
Digital Data ◽  
Survey Analysis ◽  
Critical Issues ◽  
Data Acquisition And Processing ◽  
Short Time

In recent decades, 3D acquisition by laser scanning or digital photogrammetry has become one of the standard methods of documenting cultural heritage, because it permits one to analyze the shape, geometry, and location of any artefact without necessarily coming into contact with it. The recording of three-dimensional metrical data of an asset allows one to preserve and monitor, but also to understand and explain the history and cultural heritage shared. In essence, it constitutes a digital archive of the state of an artefact, which can be used for various purposes, be remodeled, or kept safely stored. With the introduction of 3D printing, digital data can once again take on material form and become physical objects from the corresponding mathematical models in a relatively short time and often at low cost. This possibility has led to a different consideration of the concept of virtual data, no longer necessarily linked to simple visual fruition. The importance of creating high-resolution physical copies has been reassessed in light of different types of events that increasingly threaten the protection of cultural heritage. The aim of this research is to analyze the critical issues in the production process of the replicas, focusing on potential problems in data acquisition and processing and on the accuracy of the resulting 3D printing. The metric precision of the printed model with 3D technology are fundamental for everything concerning geomatics and must be related to the same characteristics of the digital model obtained through the survey analysis.

Sign in / Sign up

Export Citation Format

Share Document