Novel IC Sub-Threshold IDDQ Signature And Its Relationship To Aging During High Voltage Stress

2018 ◽  
Author(s):  
Franco Stellari ◽  
Naigang Wang ◽  
Peilin Song
Keyword(s):  
High Voltage ◽  
Voltage Stress

scholarly journals Novel High-Efficiency High Step-Up DC–DC Converter with Soft Switching and Low Component Voltage Stress for Photovoltaic System

Processes ◽  
2021 ◽  
Vol 9 (7) ◽  
pp. 1112
Author(s):  
Yu-En Wu ◽  
Jyun-Wei Wang
Keyword(s):  
High Voltage ◽  
Output Voltage ◽  
High Efficiency ◽  
Low Voltage ◽  
Leakage Inductance ◽  
Power Switch ◽  
Half Wave Voltage ◽  
Half Wave ◽  
Voltage Stress ◽  
Voltage Doubler

This study developed a novel, high-efficiency, high step-up DC–DC converter for photovoltaic (PV) systems. The converter can step-up the low output voltage of PV modules to the voltage level of the inverter and is used to feed into the grid. The converter can achieve a high step-up voltage through its architecture consisting of a three-winding coupled inductor common iron core on the low-voltage side and a half-wave voltage doubler circuit on the high-voltage side. The leakage inductance energy generated by the coupling inductor during the conversion process can be recovered by the capacitor on the low-voltage side to reduce the voltage surge on the power switch, which gives the power switch of the circuit a soft-switching effect. In addition, the half-wave voltage doubler circuit on the high-voltage side can recover the leakage inductance energy of the tertiary side and increase the output voltage. The advantages of the circuit are low loss, high efficiency, high conversion ratio, and low component voltage stress. Finally, a 500-W high step-up converter was experimentally tested to verify the feasibility and practicability of the proposed architecture. The results revealed that the highest efficiency of the circuit is 98%.

A High-Voltage ZVZCS DC--DC Converter With Low Voltage Stress

2008 ◽  
Vol 23 (6) ◽  
pp. 2630-2647 ◽  
Author(s):  
Ting-Ting Song ◽  
Huai Wang ◽  
H.S.-H. Chung ◽  
S. Tapuhi ◽  
A. Ioinovici
Keyword(s):  
High Voltage ◽  
Low Voltage ◽  
Voltage Stress

scholarly journals High Step-up Coupled Inductor Inverters Based on qSBIs

Energies ◽  
2019 ◽  
Vol 12 (15) ◽  
pp. 3032 ◽  
Author(s):  
Hongchen Liu ◽  
Xi Su ◽  
Junxiong Wang
Keyword(s):  
Steady State ◽  
High Voltage ◽  
Low Voltage ◽  
Duty Ratio ◽  
Voltage Gain ◽  
Passive Components ◽  
Steady State Analysis ◽  
High Voltage Gain ◽  
Voltage Stress ◽  
Working Principle

In this paper, two types of high step-up coupled inductor inverters based on qSBIs (quasi- switched boost inverters) are proposed. By applying the coupled inductor to the qSBIs, the voltage gain of the proposed inverter is regulated by turn ratio and duty ratio. Thus, a high voltage gain can be achieved without the circuits operating at the extreme duty cycle by choosing a suitable turn ratio of the coupled inductor. In addition, the proposed circuits have the characteristics of continuous input current and low voltage stress across the passive components. A boost unit can be added to the proposed inverters for further improvement of the voltage gain. In this paper, the working principle, steady state analysis, and the comparisons of the proposed inverter with other impedance-source inverters are described. A 200 W prototype was created and the experimental results confirm the correctness of the analysis in this paper.

scholarly journals A Modified High Voltage Gain SEPIC Based DC-DC Converter with Continuous Conduction Mode

2020 ◽  
Vol 6 (12) ◽  
pp. 268-274
Author(s):  
G.Vijaykumar and Dr.V.Geetha
Keyword(s):  
High Voltage ◽  
High Efficiency ◽  
Input Voltage ◽  
Voltage Gain ◽  
Pv System ◽  
Operating Modes ◽  
High Voltage Gain ◽  
Voltage Stress ◽  
High Output Voltage ◽  
High Output

A high voltage gain modified SEPIC converter is proposed in this paper. This proposed converter has many advantages i.e., high output voltage, lower voltage stress, high efficiency, voltage gain is high without any coupled inductor and transformer, continuous input current. Thus, there is no overshoot voltage at turn-off process for switches. By using single switches, the CCM mode operation can be easily controlled by this converter, so control system is simple and also wide output values is obtained only by modifying the duty cycle. This modified converter has lower components than conventional converter. The operating modes and design of modified converter are discussed. The output power of this converter is 6 watts. By this converter, this converter capable of developing the two and half times of input voltage. The PV system also used this converter to develop high voltage gain. This high voltage gain is achieved by using MATLAB/SIMULIMK platform.

A Robust, Composite Packaging Approach for a High Voltage 6.5kV IGBT and Series Diode

2015 ◽  
Vol 2015 (1) ◽  
pp. 000359-000364 ◽  
Author(s):  
Adam Morgan ◽  
Ankan De ◽  
Haotao Ke ◽  
Xin Zhao ◽  
Kasunaidu Vechalapu ◽  
...  
Keyword(s):  
High Voltage ◽  
Thermal Stresses ◽  
Wide Bandgap ◽  
Power Module ◽  
Cost Performance ◽  
Power Semiconductor ◽  
Current Switch ◽  
Power Modules ◽  
Voltage Stress ◽  
3D Printed

The main motivation of this work is to design, fabricate, test, and compare an alternative, robust packaging approach for a power semiconductor current switch. Packaging a high voltage power semiconductor current switch into a single power module, compared to using separate power modules, offers cost, performance, and reliability advantages. With the advent of Wide-Bandgap (WBG) semiconductors, such as Silicon-Carbide, singular power electronic devices, where a device is denoted as a single transistor or rectifier unit on a chip, can now operate beyond 10kV–15kV levels and switch at frequencies within the kHz range. The improved voltage blocking capability reduces the number of series connected devices within the circuit, but challenges power module designers to create packages capable of managing the electrical, mechanical, and thermal stresses produced during operation. The non-sinusoidal nature of this stress punctuated with extremely fast changes in voltage and current, with respect to time, leads to non-ideal electrical and thermal performance. An optimized power semiconductor series current switch is fabricated using an IGBT (6500V/25A die) and SiC JBS Diode (6000V/10A), packaged into a 3D printed housing, to create a composite series current switch package (CSCSP). The final chosen device configuration was simulated and verified in an ANSYS software package. Also, the thermal behavior of such a composite package was simulated and verified using COMSOL. The simulated results were then compared with empirically obtained data, in order to ensure that the thermal ratings of the power devices were not exceeded; directly affecting the maximum attainable frequency of operation for the CSCSP. Both power semiconductor series current switch designs are tested and characterized under hard switching conditions. Special attention is given to ensure the voltage stress across the devices is significantly reduced.

scholarly journals Modified Cascaded Z-Source High Step-Up Boost Converter

Electronics ◽  
2020 ◽  
Vol 9 (11) ◽  
pp. 1932
Author(s):  
Navid Salehi ◽  
Herminio Martínez-García ◽  
Guillermo Velasco-Quesada
Keyword(s):  
High Voltage ◽  
Boost Converter ◽  
Experimental Results ◽  
Input Current ◽  
Voltage Gain ◽  
Low Input ◽  
High Voltage Gain ◽  
Voltage Stress ◽  
Photovoltaic Applications ◽  
Current Ripple

To improve the voltage gain of step-up converters, the cascaded technique is considered as a possible solution in this paper. By considering the concept of cascading two Z-source networks in a conventional boost converter, the proposed topology takes the advantages of both impedance source and cascaded converters. By applying some modifications, the proposed converter provides high voltage gain while the voltage stress of the switch and diodes is still low. Moreover, the low input current ripple of the converter makes it absolutely appropriate for photovoltaic applications in expanding the lifetime of PV panels. After analyzing the operation principles of the proposed converter, we present the simulation and experimental results of a 100 W prototype to verify the proposed converter performance.

Sign in / Sign up

Export Citation Format

Share Document