An enhanced Folded Cascode op-amp in 0.18 µm CMOS process with 67dB dc-gain

2011 ◽  
Author(s):  
Banafsheh Alizadeh ◽  
Ali Dadashi
Keyword(s):  
Cmos Process ◽  
Op Amp ◽  
Dc Gain ◽  
Folded Cascode

A 1-mm2 CMOS-pipelined ADC with integrated folded cascode operational amplifier

2020 ◽  
Vol 37 (4) ◽  
pp. 205-213
Author(s):  
Norhamizah Idros ◽  
Zulfiqar Ali Abdul Aziz ◽  
Jagadheswaran Rajendran
Keyword(s):  
Operational Amplifier ◽  
Open Loop ◽  
Cmos Process ◽  
Silicon Area ◽  
Content Type ◽  
Op Amp ◽  
Dc Gain ◽  
Input Range ◽  
Folded Cascode ◽  
The Impact

Purpose The purpose of this paper is to demonstrate the acceptable performance by using the limited input range towards lower open-loop DC gain operational amplifier (op-amp) of an 8-bit pipelined analog-to-digital converter (ADC) for mobile communication application. Design/methodology/approach An op-amp with folded cascode configuration is designed to provide the maximum open-loop DC gain without any gain-boosting technique. The impact of low open-loop DC gain is observed and analysed through the results of pre-, post-layout simulations and measurement of the ADC. The fabrication process technology used is Silterra 0.18-µm CMOS process. The silicon area by the ADC is 1.08 mm2. Findings Measured results show the differential non-linearity (DNL) error, integral non-linearity (INL) error, signal-to-noise ratio (SNR) and spurious-free dynamic range (SFDR) are within −0.2 to +0.2 LSB, −0.55 LSB for 0.4 Vpp input range, 22 and 27 dB, respectively, with 2 MHz input signal at the rate of 64 MS/s. The static power consumption is 40 mW with a supply voltage of 1.8 V. Originality/value The experimental results of ADC showed that by limiting the input range to ±0.2 V, this ADC is able to give a good reasonable performance. Open-loop DC gain of op-amp plays a critical role in ADC performance. Low open-loop DC gain results in stage-gain error of residue amplifier and, thus, leads to nonlinearity of output code. Nevertheless, lowering the input range enhances the linearity to ±0.2 LSB.

Design of High Gain Folded Cascode OTA-Based Transconductance–Capacitance Loop Filter for PLL Applications

2021 ◽  
pp. 2150263
Author(s):  
Priti Gupta ◽  
Sanjay Kumar Jana
Keyword(s):  
Power Consumption ◽  
Supply Voltage ◽  
High Gain ◽  
Cmos Process ◽  
Operational Transconductance Amplifier ◽  
Loop Filter ◽  
Transconductance Amplifier ◽  
Dc Gain ◽  
Unity Gain ◽  
Folded Cascode

This paper deals with the designing of low-power transconductance–capacitance-based loop filter. The folded cascode-based operational transconductance amplifier (OTA) is designed in this paper with the help of quasi-floating bulk MOSFET that achieved the DC gain of 88.61[Formula: see text]dB, unity gain frequency of 97.86[Formula: see text]MHz and power consumption of 430.62[Formula: see text][Formula: see text]W. The proposed OTA is compared with the exiting OTA structure which showed 19.50% increase in DC gain and 15.11% reduction in power consumption. Further, the proposed OTA is used for the designing of transconductance–capacitance-based loop filter that has been operated at [Formula: see text]3[Formula: see text]dB cut-off frequency of 30.12[Formula: see text]MHz with the power consumption of 860.90[Formula: see text][Formula: see text]W at the supply voltage of [Formula: see text][Formula: see text]V. The transistor-level simulation has been done in 0.18[Formula: see text][Formula: see text]m CMOS process.

An enhanced folded cascode Op-Amp using positive feedback and bulk amplification in 0.35 μm CMOS process

2010 ◽  
Vol 67 (2) ◽  
pp. 213-222 ◽  
Author(s):  
Ali Dadashi ◽  
Shamin Sadrafshari ◽  
Khayrollah Hadidi ◽  
Abdollah Khoei
Keyword(s):  
Positive Feedback ◽  
Cmos Process ◽  
Op Amp ◽  
Folded Cascode

Design of High Gain CMOS Folded Cascode Operational Amplifier

2013 ◽  
Vol 389 ◽  
pp. 573-578
Author(s):  
Ming Xin Song ◽  
Yue Li ◽  
Meng Meng Xu
Keyword(s):  
Power Supply ◽  
Operational Amplifier ◽  
High Gain ◽  
Cmos Process ◽  
Phase Margin ◽  
Gain Bandwidth ◽  
Input Stage ◽  
Dc Gain ◽  
Unity Gain ◽  
Folded Cascode

A high-gain folded cascode operational amplifier is presented. Structure of folded cascode operational amplifier and manual calculations are discussed in detail. Folded cascode structure for the input stage is adopted. Folded cascode structure can increase the gain and the value of PSRR. Folded cascode structure can also allow self-compensation at the output. The operational amplifier is designed in 0.35μm CMOS process with 5V power supply. The operational amplifier has high-gain and work steadily. The results of SPICE simulations are shown that the operational amplifier achieved dc gain of 110dB with unity-gain bandwidth of 74.3MHz and phase margin of 54.4 degree.

scholarly journals Design Strategies and Architectures for Ultra-Low-Voltage Delta-Sigma ADCs

Electronics ◽  
2021 ◽  
Vol 10 (10) ◽  
pp. 1156
Author(s):  
Lorenzo Benvenuti ◽  
Alessandro Catania ◽  
Giuseppe Manfredini ◽  
Andrea Ria ◽  
Massimo Piotto ◽  
...  
Keyword(s):  
Low Voltage ◽  
Flicker Noise ◽  
Supply Voltage ◽  
Cmos Process ◽  
Clock Frequency ◽  
Design Environment ◽  
Ultra Low Power ◽  
Analog Cmos ◽  
Gain Error ◽  
Dc Gain

The design of ultra-low voltage analog CMOS integrated circuits requires ad hoc solutions to counteract the severe limitations introduced by the reduced voltage headroom. A popular approach is represented by inverter-based topologies, which however may suffer from reduced finite DC gain, thus limiting the accuracy and the resolutions of pivotal circuits like analog-to-digital converters. In this work, we discuss the effects of finite DC gain on ultra-low voltage ΔΣ modulators, focusing on the converter gain error. We propose an ultra-low voltage, ultra-low power, inverter-based ΔΣ modulator with reduced finite-DC-gain sensitivity. The modulator employs a two-stage, high DC-gain, switched-capacitor integrator that applies a correlated double sampling technique for offset cancellation and flicker noise reduction; it also makes use of an amplifier that implements a novel common-mode stabilization loop. The modulator was designed with the UMC 0.18 μm CMOS process to operate with a supply voltage of 0.3 V. It was validated by means of electrical simulations using the CadenceTM design environment. The achieved SNDR was 73 dB, with a bandwidth of 640 Hz, and a clock frequency of 164 kHz, consuming only 200.5 nW. It achieves a Schreier Figure of Merit of 168.1 dB. The proposed modulator is also able to work with lower supply voltages down to 0.15 V with the same resolution and a lower power consumption despite of a lower bandwidth. These characteristics make this design very appealing in sensor interfaces powered by energy harvesting sources.

Sign in / Sign up

Export Citation Format

Share Document