Author(s):  
Urvashi Bansal ◽  
Abhilasha Bakre ◽  
Prem Kumar ◽  
Devansh Yadav ◽  
Mohit Kumar ◽  
...  

A low voltage low power two-stage CMOS amplifier with high open-loop gain, high gain bandwidth product (GBW) and enhanced slew rate is presented in this work. The proposed circuit makes use of folded cascode gm-boosting cells in conjunction with a low voltage gain enhanced cascode mirror using quasi-floating gate (QFGMOS) transistors. QFGMOS transistors are also used in input pair and adaptive biasing, which facilitate large dynamic output current in the presented circuit. Consequently, the slew rate is enhanced without much increase in static power dissipation. The unity gain frequency (UGF) and dc gain of the circuit are 29.4[Formula: see text]MHz and 132[Formula: see text]dB, respectively. The amplifier is operated at 0.6[Formula: see text]V dual supply with 89[Formula: see text][Formula: see text]W power consumption and has a nearly symmetrical average slew rate of 51.5[Formula: see text]V/[Formula: see text]s. All simulations including Monte Carlo and corner analysis are carried out using 180-nm CMOS technology for validating the design with help of spice tools.


Author(s):  
Nagendra Tiwari ◽  
Bharati Chourasia

In this paper dynamic biasing technique is used for the enhancing the slew rate of the designed Op-Amp. The proposed FinFET based Op-Amp has been verified through Hspice simulator in the standard 45nm Silicon on Insulator FinFET library. The proposed op amp has two stages Miller compensated configuration. A biasing circuit (DSB circuit) is used for dynamic switching of the biasing voltage of the op amp. This leads to lower power consumption, wide ICMR range, and high gain stability. The proposed op amp has a power consumption of 661.83 μW. It has a dual supply voltage of -1.0V and 1.0V. The input common mode range (ICMR) is -800 mV to +900 mV. The Op-Amp has a slew rate of 1.5 KV/μs. Voltage gain of the op amp is 90.4dB. Due to the use of SOI FINFET devices the op amp has relatively less leakage current as compared to similar bulk MOSFET device op amps. The op amp has unity gain bandwidth of 1.27 GHz. Thus, it can be used to transmission and processing of audio and video signals.


2020 ◽  
Vol 12 (3) ◽  
pp. 168-174
Author(s):  
Rashmi Sahu ◽  
Maitraiyee Konar ◽  
Sudip Kundu

Background: Sensing of biomedical signals is crucial for monitoring of various health conditions. These signals have a very low amplitude (in μV) and a small frequency range (<500 Hz). In the presence of various common-mode interferences, biomedical signals are difficult to detect. Instrumentation amplifiers (INAs) are usually preferred to detect these signals due to their high commonmode rejection ratio (CMRR). Gain accuracy and CMRR are two important parameters associated with any INA. This article, therefore, focuses on the improvement of the gain accuracy and CMRR of a low power INA topology. Objective: The objective of this article is to achieve high gain accuracy and CMRR of low power INA by having high gain operational amplifiers (Op-Amps), which are the building blocks of the INAs. Methods: For the implementation of the Op-Amps and the INAs, the Cadence Virtuoso tool was used. All the designs and implementation were realized in 0.18 μm CMOS technology. Results: Three different Op-Amp topologies namely single-stage differential Op-Amp, folded cascode Op-Amp, and multi-stage Op-Amp were implemented. Using these Op-Amp topologies separately, three Op-Amp-based INAs were realized and compared. The INA designed using the high gain multistage Op-Amp topology of low-frequency gain of 123.89 dB achieves a CMRR of 164.1 dB, with the INA’s gain accuracy as good as 99%, which is the best when compared to the other two INAs realized using the other two Op-Amp topologies implemented. Conclusion: Using very high gain Op-Amps as the building blocks of the INA improves the gain accuracy of the INA and enhances the CMRR of the INA. The three Op-Amp-based INA designed with the multi-stage Op-Amps shows state-of-the-art characteristics as its gain accuracy is 99% and CMRR is as high as 164.1 dB. The power consumed by this INA is 29.25 μW by operating on a power supply of ±0.9V. This makes this INA highly suitable for low power measurement applications.


Sign in / Sign up

Export Citation Format

Share Document