A 3.3dB Noise Figure,60-mW CMOS Receiver Front End for 865-867 MHz Band

2018 ◽  
Author(s):  
Awdhesh Pandey ◽  
Ankita Verma ◽  
Prasanna Kumar Misra
Keyword(s):  
Noise Figure ◽  
Front End ◽  
Cmos Receiver

scholarly journals A 1.5–40 GHz frequency modulated continuous wave radar receiver front-end

2021 ◽  
pp. 1-11
Author(s):  
Mantas Sakalas ◽  
Niko Joram ◽  
Frank Ellinger
Keyword(s):  
Continuous Wave ◽  
Noise Figure ◽  
Supply Voltage ◽  
Low Noise ◽  
Ultra Wideband ◽  
Front End ◽  
Wave Radar ◽  
Bicmos Technology ◽  
Circuit Components ◽  
High Band

Abstract This study presents an ultra-wideband receiver front-end, designed for a reconfigurable frequency modulated continuous wave radar in a 130 nm SiGe BiCMOS technology. A variety of innovative circuit components and design techniques were employed to achieve the ultra-wide bandwidth, low noise figure (NF), good linearity, and circuit ruggedness to high input power levels. The designed front-end is capable of achieving 1.5–40 GHz bandwidth, 30 dB conversion gain, a double sideband NF of 6–10.7 dB, input return loss better than 7.5 dB and an input referred 1 dB compression point of −23 dBm. The front-end withstands continuous wave power levels of at least 25 and 20 dBm at low band and high band inputs respectively. At 3 V supply voltage, the DC power consumption amounts to 302 mW when the low band is active and 352 mW for the high band case, whereas the total IC size is $3.08\, {\rm nm{^2}}$ .

RF Sensor Modules – Needs for Multifunctional Architectures

2016 ◽  
Vol 2016 (CICMT) ◽  
pp. 000207-000210
Author(s):  
Martin Oppermann ◽  
Felix Thurow ◽  
Ralf Rieger
Keyword(s):  
Noise Figure ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Low Loss ◽  
Reflow Soldering ◽  
Operating Modes ◽  
Front End ◽  
Multilayer Ceramic ◽  
Noise Amplifier ◽  
Rf Pcb

Abstract Next generation of RF sensor modules, mainly for airborne applications, will cover a variety of multifunction in terms of different operating modes, e.g. Radar, EW and Communications / Datalinks. The operating frequencies will cover a bandwidth of > 10 GHz and for realisation of modern Active Electronically Steered Antennas (AESA) the Transmit/Receive (T/R) modules have to match with challenging geometry demands, and RF requirements, like switching and filtering between different operational frequencies in transmit and receive mode. New GaN technology based MMICs, e.g. LNA, HPA are in development and multifunctional components (MFC MMICs) cover more than one RF function in one chip. Different front end demonstrators will be presented, based on multilayer ceramic (LTCC) and RF-PCB and associated assembly technologies, like chip&wire and SMD reflow soldering. These TRM front ends include a Low Noise Amplifier with an integrated Switch (LNA/SW) and for characterisation the measured Noise Figure (NF), a key characteristic for receive performance, will be compared. The need for high integration on module level is obvious and therefore specific demands for low loss ceramic and PCB based modules, packages and housings exist.

Design of a Front-End for Satellite Receiver

2016 ◽  
Vol 6 (5) ◽  
pp. 2282 ◽  
Author(s):  
Tran Van Hoi ◽  
Ngo Thi Lanh ◽  
Nguyen Xuan Truong ◽  
Nguyen Huu Duc ◽  
Bach Gia Duong
Keyword(s):  
Dynamic Range ◽  
Noise Figure ◽  
High Sensitivity ◽  
Wide Band ◽  
Local Oscillator ◽  
Low Noise ◽  
Voltage Controlled Oscillator ◽  
Front End ◽  
L Band ◽  
Satellite Receiver

<p>This paper focuses on the design and implementation of a front-end for a Vinasat satellite receiver with auto-searching mechanism and auto-tracking satellite. The front-end consists of a C-band low-noise block down-converter and a L-band receiver. The receiver is designed to meet the requirements about wide-band, high sensitivity, large dynamic range, low noise figure. To reduce noise figure and increase bandwidth, the C-band low-noise amplifier is designed using T-type of matching network with negative feedback and the L-band LNA is designed using cascoded techniques. The local oscillator uses a voltage controlled oscillator combine phase locked loop to reduce the phase noise and select channels. The front-end has successfully been designed and fabricated with parameters: Input frequency is C-band; sensitivity is greater than -130 dBm for C-band receiver and is greater than -110dBm for L-band receiver; output signals are AM/FM demodulation, I/Q demodulation, baseband signals.</p>

High Gain and Low Noise Single Balanced Wireless Receiver Front-End Circuit Design

2013 ◽  
Vol 284-287 ◽  
pp. 2647-2651
Author(s):  
Zhe Yang Huang ◽  
Che Cheng Huang ◽  
Jung Mao Lin ◽  
Chung Chih Hung
Keyword(s):  
Return Loss ◽  
Noise Figure ◽  
High Gain ◽  
Low Noise ◽  
Total Power ◽  
Cmos Process ◽  
Chip Area ◽  
Wireless Receiver ◽  
Front End ◽  
Total Power Consumption

This paper presents a wideband wireless receiver front-end for 3.1-5.0GHz band group-1 (BG-1) WiMedia application. The front-end circuits are designed in 0.18um standard CMOS process. The experimental results show the maximum conversion power gain is 45.5dB; minimum noise figure is 2.9dB. Input return loss is lower than -9.3dB and output return loss is lower than -6.8dB. The maximum LO conversion power is 0dBm. 3dB working frequency is 1.9GHz (3.1GHz-5.0GHz) Total power consumption is 24.3mW including LNA, mixer and all buffers. Total chip area is 1.27mm2 including dummy and pads.

A 2.4-GHz sub-mW CMOS receiver front-end for wireless sensors network

2006 ◽  
Vol 16 (4) ◽  
pp. 206-208 ◽  
Author(s):  
Taeksang Song ◽  
Hyoung-Seok Oh ◽  
Songcheol Hong ◽  
Euisik Yoon
Keyword(s):  
Wireless Sensors ◽  
Front End ◽  
Wireless Sensors Network ◽  
Cmos Receiver

Study on Performance Analysis of CMOS RF front-end circuits for 2.4GHz Wireless Applications

2012 ◽  
pp. 68-73
Author(s):  
M. Sumathi ◽  
S. Malarvizhi
Keyword(s):  
Performance Analysis ◽  
Low Voltage ◽  
Noise Figure ◽  
Supply Voltage ◽  
Low Noise ◽  
Design System ◽  
Wireless Applications ◽  
Front End ◽  
Trade Offs ◽  
Front End Circuits

In this paper, low voltage design concepts and new CMOS front-end circuits for 2.4GHz wireless applications are presented. The performances of these circuits are analysed and compared with other existing structures using TSMC 0.18-μm CMOS technology scale. The design trade-offs between impedance matching, power gain and noise figure of low-noise amplifiers are highlighted. The advantage of the introduced mixer topology is expressed in terms of conversion gain, noise figure and linearity. At a supply voltage of 1.8V, the design and performance analysis have been performed using Agilent’s Advanced Design System (ADS2009) software.

Sign in / Sign up

Export Citation Format

Share Document