Complex impedance of a bar in apartially open slot of a rotor

2006 ◽  
Author(s):  
V.V. Grechkin ◽  
A.I. Hikin ◽  
Z.S. Temlyakova
Keyword(s):  
Complex Impedance

Effect of MCl (M = Na, K) addition on microstructure and electrical conductivity of forsterite

2020 ◽  
Vol 92 (1) ◽  
pp. 10901
Author(s):  
Saloua El Asri ◽  
Hamid Ahamdane ◽  
Lahoucine Hajji ◽  
Mohamed El Hadri ◽  
Moulay Ahmed El Idrissi Raghni ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Electrical Conductivity ◽  
Single Phase ◽  
Sol Gel ◽  
Complex Impedance ◽  
Transmission Spectra ◽  
Electrical Measurements ◽  
Cation Type ◽  
Edx Analyses ◽  
The Fourier Transform

Forsterite single phase powder Mg2SiO4 was synthesized by sol–gel method alongside with heat treatment, using two different cation alkaline salts MCl as mineralizers (M = Na, K) with various mass percentages (2.5, 5, 7.5, and 10 wt.%). In this work, we report on the effect of the cation type and the added amount of used mineralizer on microstructure and electrical conductivity of Mg2SiO4. The formation of forsterite started at 680–740  °C and at 630–700  °C with KCl and NaCl respectively, as shown by TG-DTA and confirmed by XRD. Furthermore, the Fourier transform infrared (FTIR) transmission spectra indicated bands corresponding to vibrations of forsterite structure. The morphology and elemental composition of sintered ceramics were examined by SEM-EDX analyses, while their densities, which were measured by Archimedes method, increased with addition of both alkaline salts. The electrical measurements were performed by Complex Impedance Spectroscopy. The results showed that electrical conductivity increased with the addition of both mineralizers, which was higher for samples prepared with NaCl than those prepared with KCl.

A UHF Compact Complex Impedance-transforming Balun with High Isolation

2020 ◽  
Vol 13 (8) ◽  
pp. 1135-1144
Author(s):  
Kittipong Nithiporndecha ◽  
Chatrpol Pakasiri
Keyword(s):  
Complex Impedance ◽  
Output Port ◽  
Reflection Coefficients ◽  
Coupled Line ◽  
High Isolation ◽  
Line Structure ◽  
Source Impedance ◽  
Phase Balance ◽  
High Output

Background: A compact complex impedance-transforming balun for UHF frequencies, which is based on a coupled-line structure that matched all ports and provided high output port isolation, was designed in this paper. Methods: A lumped component transformation was used to minimize circuit size. The implemented circuit operated at 433 MHz with the reflection coefficients less than -16 dB at all ports, 0.22 dB amplitude balance and 180° phase balance at the output ports. The signal coupling between the output ports was -16.8 dB. The circuit size is small at 0.032λ. Results: Complex impedance-transforming baluns were designed to operate at 433 MHz. The source impedance at port 1 was set at Zs = 12 - j12Ω and the load impedances at port 2 and 3 were set at ZL = 80 + j30Ω. Conclusion: A compact complex impedance-transforming balun at UHF frequency, with all ports matched and high isolations, was designed and illustrated in this paper.

Primary involvement of K+ conductance in membrane resonance of trigeminal root ganglion neurons

1988 ◽  
Vol 59 (1) ◽  
pp. 77-89 ◽  
Author(s):  
E. Puil ◽  
B. Gimbarzevsky ◽  
I. Spigelman
Keyword(s):  
Electrical Properties ◽  
Channel Blocker ◽  
Complex Impedance ◽  
Membrane Potentials ◽  
K Channel ◽  
Bathing Medium ◽  
Trigeminal Root ◽  
Membrane Resonance ◽  
Ganglion Neurons ◽  
Impedance Magnitude

1. The complex impedances and impedance magnitude functions were obtained from neurons in in vitro slices of trigeminal root ganglia using frequency-domain analyses of intracellularly recorded voltage responses to specified oscillatory input currents. A neuronal model derived from linearized Hodgkin-Huxley-like equations was used to fit the complex impedance data. This procedure yielded estimates for membrane electrical properties. 2. Membrane resonance was observed in the impedance magnitude functions of all investigated neurons at their initial resting membrane potentials and was similar to that reported previously for trigeminal root ganglion neurons in vivo. Tetrodotoxin (10(-6) M), a Na+-channel blocker, applied in the bathing medium for 20 min produced only minor changes, if any, in the resonance, although gross impairment of Na+-spike electrogenesis was apparent in most of the neurons. Brief applications (1-5 min) of a K+-channel blocker, tetraethylammonium (TEA; 10(-2) M), increased the impedance magnitude and abolished, in a reversible manner, the resonant behavior. In all cases, the resonant frequency was decreased by TEA administration prior to total blockade of resonance. 3. The TEA-induced blockade of resonance was associated with decreases in the estimates of the membrane conductances, without significant alterations of input capacitance. A particularly large decrease was observed in Gr, the time-invariant resting conductance that includes a lumped leak conductance component. The voltage- and time-dependent conductance, GL, and associated relaxation time constant, tau u, also declined progressively during administration of TEA. 4. Systematic variations in the membrane potentials of trigeminal root ganglion neurons were produced by intracellular injections of long-lasting step currents with superposition of the oscillatory current stimuli, in order to assess the effects of TEA on the relationship of the electrical properties to the membrane potential. Applications of TEA led to a depolarizing shift in the dependence of the membrane property estimates, suggesting voltage-dependence of the effects of TEA on presumed K+ channels in the membrane. 5. These data suggest a primary involvement of K+ conductance in the genesis of membrane resonance. This electrical behavior or its ionic mechanism is a major modulator of the subthreshold electrical responsiveness of trigeminal root ganglion neurons.

scholarly journals Near-Field Scanning Millimeter-Wave Microscope Operating Inside a Scanning Electron Microscope: Towards Quantitative Electrical Nanocharacterization

2021 ◽  
Vol 11 (6) ◽  
pp. 2788
Author(s):  
Petr Polovodov ◽  
Didier Théron ◽  
Clément Lenoir ◽  
Dominique Deresmes ◽  
Sophie Eliet ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Millimeter Wave ◽  
Radiation Effects ◽  
Near Field ◽  
Complex Impedance ◽  
Standard Operating Procedure ◽  
Critical Issue ◽  
Transverse Electromagnetic ◽  
Scanning Electron

The main objectives of this work are the development of fundamental extensions to existing scanning microwave microscopy (SMM) technology to achieve quantitative complex impedance measurements at the nanoscale. We developed a SMM operating up to 67 GHz inside a scanning electron microscope, providing unique advantages to tackle issues commonly found in open-air SMMs. Operating in the millimeter-wave frequency range induces high collimation of the evanescent electrical fields in the vicinity of the probe apex, resulting in high spatial resolution and enhanced sensitivity. Operating in a vacuum allows for eliminating the water meniscus on the tip apex, which remains a critical issue to address modeling and quantitative analysis at the nanoscale. In addition, a microstrip probing structure was developed to ensure a transverse electromagnetic mode as close as possible to the tip apex, drastically reducing radiation effects and parasitic apex-to-ground capacitances with available SMM probes. As a demonstration, we describe a standard operating procedure for instrumentation configuration, measurements and data analysis. Measurement performance is exemplarily shown on a staircase microcapacitor sample at 30 GHz.

scholarly journals Impedance Spectroscopic Study of Nickel Sulfide Nanostructures Deposited by Aerosol Assisted Chemical Vapor Deposition Technique

Nanomaterials ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 1105
Author(s):  
Sadia Iram ◽  
Azhar Mahmood ◽  
Muhammad Fahad Ehsan ◽  
Asad Mumtaz ◽  
Manzar Sohail ◽  
...  
Keyword(s):  
Chemical Vapor Deposition ◽  
Vapor Deposition ◽  
Nickel Sulfide ◽  
Variable Temperature ◽  
Complex Impedance ◽  
Equivalent Circuit Model ◽  
Chemical Vapor ◽  
Relaxation Processes ◽  
Impedance Plot ◽  
Vapor Deposition Technique

This research aims to synthesize the Bis(di-isobutyldithiophosphinato) nickel (II) complex [Ni(iBu2PS2)] to be employed as a substrate for the deposition of nickel sulfide nanostructures, and to investigate its dielectric and impedance characteristics for applications in the electronic industry. Various analytical tools including elemental analysis, mass spectrometry, IR, and TGA were also used to further confirm the successful synthesis of the precursor. NiS nanostructures were grown on the glass substrates by employing an aerosol assisted chemical vapor deposition (AACVD) technique via successful decomposition of the synthesized complex under variable temperature conditions. XRD, SEM, TEM, and EDX methods were well applied to examine resultant nanostructures. Dielectric studies of NiS were carried out at room temperature within the 100 Hz to 5 MHz frequency range. Maxwell-Wagner model gave a complete explanation of the variation of dielectric properties along with frequency. The reason behind high dielectric constant values at low frequency was further endorsed by Koops phenomenological model. The efficient translational hopping and futile reorientation vibration caused the overdue exceptional drift of ac conductivity (σac) along with the rise in frequency. Two relaxation processes caused by grains and grain boundaries were identified from the fitting of a complex impedance plot with an equivalent circuit model (Rg Cg) (Rgb Qgb Cgb). Asymmetry and depression in the semicircle having center present lower than the impedance real axis gave solid justification of dielectric behavior that is non-Debye in nature.

Impedance Analysis of Layer Structured NBT–CBT Mixed Ceramics

1998 ◽  
Vol 12 (11) ◽  
pp. 433-441 ◽  
Author(s):  
P. S. Rama Sastry ◽  
T. Bhimasankaram ◽  
G. S. Kumar ◽  
G. Prasad
Keyword(s):  
Comparative Study ◽  
Complex Impedance ◽  
Impedance Analysis ◽  
Equivalent Circuits ◽  
Impedance Spectra ◽  
Ceramic System ◽  
Different Temperatures ◽  
Mixed Ceramics ◽  
Mixed Ceramic ◽  
Complex Impedance Spectra

Complex impedance spectra of ferroelectric mixed ceramic system ( Na 0.5 Bi 0.5)1-x Ca x Bi 4 Ti 4 O 15 with x=0, 0.1, 0.3, 0.5, 0.7 and 1 was studied as a function of frequency and temperature in the range 1 KHz to 10 MHz and 30°C to 620°C respectively. Equivalent circuits involving resistive and capacitive elements at different temperatures, activation energies of relaxations and conduction were evaluated using impedance plots. A comparative study of impedance and conductivity facilities an insight in understanding the electrical nature of these electroceramics.

Electrical Conductivity and Structural Studies on the Binary System BiI3-Ag2SO4

2012 ◽  
Vol 584 ◽  
pp. 521-525
Author(s):  
S. Austin Suthanthiraraj ◽  
Ayesha Saleem
Keyword(s):  
Electrical Conductivity ◽  
Binary System ◽  
Ionic Conduction ◽  
Structural Characteristics ◽  
Complex Impedance ◽  
Present System ◽  
Rapid Melt Quenching ◽  
Ionic Nature ◽  
Electrochemical Devices ◽  
Silver Sulphate

A new solid-state pseudo binary system BiI3_-Ag2SO4 involving bismuth triiodide (BiI3) and a silver oxysalt namely silver sulphate (Ag2SO4) has been prepared using rapid melt-quenching technique. AC conductivity studies have been carried out on the nine different samples of the (BiI3)x –- (Ag2SO4)(1-x) system with compositions corresponding to x=0.1,0.2,0.3,0.4,0.5,0.6,0.7,0.8 and 0.9 mole fraction at temperatures ranging from room temperature (298 K) to 433K. The bulk resistance values estimated using complex impedance plots indicated that electrical conductivity of the synthesized solid specimens would vary from 2.9 x10-2 to 3.4 x10-6Scm-1 thus suggesting the present system to be ionic in nature. The extent of ionic conduction due to Ag + cation has also been analyzed using Wagner’s dc polarization technique whereas detailed structural characteristics of the various compositions derived from Fourier transform infrared (FTIR) spectroscopy and features of surface morphology of these samples obtained using scanning electron microscopy (SEM) have further supported the ionic nature of the chosen system and suggested possible application as a solid electrolyte in electrochemical devices.

Dielectric Loss in Vanadyl Pnictates

1990 ◽  
Vol 210 ◽  
Author(s):  
Joseph F. Lomax ◽  
John J. Fontanella ◽  
Mary C. Wintersgill ◽  
Anthony Kotarski
Keyword(s):  
Dielectric Loss ◽  
Complex Impedance ◽  
Audio Frequency ◽  
Vanadyl Phosphate ◽  
Nonstoichiometric Compound ◽  
Proton Movement ◽  
Related Compounds ◽  
Water Species ◽  
Acid Nature ◽  
Chemical Evidence

AbstractThe results of audio frequency complex impedance studies for vanadyl phosphate and its hydrates (VOPO4*nH2O;n=0,1,2) are reported. Measurements were made at seventeen frequencies between 10 and 105 Hz over the temperature range 5.5-380K. Two lowtemperature features were observed and are correlated with particular water species between the VOPO4 layers. In light of chemical evidence and compleximpedance measurements on related compounds, it is speculated that VOPCO4*nH2O (Pc = P, As) can be thought of as a mixed nonstoichiometric compound [VO(HPcO4)]x[VOPcO4O4]1-x*nH2O and the solid Brϕnsted acid nature of the compound is related to proton movement between layer pnictates and intralayer waters.

Sign in / Sign up

Export Citation Format

Share Document