Resizable scanning raster generation in television optical microscope

2016 ◽  
Author(s):  
Volodymyr Shkliarskyi ◽  
Yuriy Matiyeshyn ◽  
Rostyslav Matviyiv ◽  
Vitaliy Goy
Keyword(s):  
Optical Microscope

Some early history of replica techniques for electron microscopy

1992 ◽  
Vol 50 (2) ◽  
pp. 1076-1077
Author(s):  
Robert M. Fisher
Keyword(s):  
Thin Film ◽  
Electron Microscopy ◽  
Optical Microscope ◽  
Early History ◽  
Bulk Materials ◽  
Thin Sections ◽  
Transmission Electron ◽  
Reflected Light ◽  
History Of ◽  
Electron Microscopes

By 1940, a half dozen or so commercial or home-built transmission electron microscopes were in use for studies of the ultrastructure of matter. These operated at 30-60 kV and most pioneering microscopists were preoccupied with their search for electron transparent substrates to support dispersions of particulates or bacteria for TEM examination and did not contemplate studies of bulk materials. Metallurgist H. Mahl and other physical scientists, accustomed to examining etched, deformed or machined specimens by reflected light in the optical microscope, were also highly motivated to capitalize on the superior resolution of the electron microscope. Mahl originated several methods of preparing thin oxide or lacquer impressions of surfaces that were transparent in his 50 kV TEM. The utility of replication was recognized immediately and many variations on the theme, including two-step negative-positive replicas, soon appeared. Intense development of replica techniques slowed after 1955 but important advances still occur. The availability of 100 kV instruments, advent of thin film methods for metals and ceramics and microtoming of thin sections for biological specimens largely eliminated any need to resort to replicas.

Near-field scanning optical microscopy

1986 ◽  
Vol 44 ◽  
pp. 642-643
Author(s):  
E. Betzig ◽  
A. Harootunian ◽  
M. Isaacson ◽  
A. Lewis
Keyword(s):  
Near Field ◽  
Optical Microscope ◽  
Visible Radiation ◽  
Field Methods ◽  
Optical Elements ◽  
Optical Region ◽  
Order Of Magnitude ◽  
Nondestructive Imaging ◽  
Scanning Optical Microscopy ◽  
Near Field Scanning

In general, conventional methods of optical imaging are limited in spatial resolution by either the wavelength of the radiation used or by the aberrations of the optical elements. This is true whether one uses a scanning probe or a fixed beam method. The reason for the wavelength limit of resolution is due to the far field methods of producing or detecting the radiation. If one resorts to restricting our probes to the near field optical region, then the possibility exists of obtaining spatial resolutions more than an order of magnitude smaller than the optical wavelength of the radiation used. In this paper, we will describe the principles underlying such "near field" imaging and present some preliminary results from a near field scanning optical microscope (NS0M) that uses visible radiation and is capable of resolutions comparable to an SEM. The advantage of such a technique is the possibility of completely nondestructive imaging in air at spatial resolutions of about 50nm.

Principles of Low-Vacuum SEM

1992 ◽  
Vol 50 (2) ◽  
pp. 1304-1305
Author(s):  
Klaus-Ruediger Peters
Keyword(s):  
New Technologies ◽  
High Vacuum ◽  
Optical Microscope ◽  
Specimen Surface ◽  
Electrical Field ◽  
Gaseous Environment ◽  
New Information ◽  
Gas Molecules ◽  
New Interactions ◽  
Gas Pressures

Only recently it became possible to expand scanning electron microscopy to low vacuum and atmospheric pressure through the introduction of several new technologies. In principle, only the specimen is provided with a controlled gaseous environment while the optical microscope column is kept at high vacuum. In the specimen chamber, the gas can generate new interactions with i) the probe electrons, ii) the specimen surface, and iii) the specimen-specific signal electrons. The results of these interactions yield new information about specimen surfaces not accessible to conventional high vacuum SEM. Several microscope types are available differing from each other by the maximum available gas pressure and the types of signals which can be used for investigation of specimen properties.Electrical non-conductors can be easily imaged despite charge accumulations at and beneath their surface. At high gas pressures between 10-2 and 2 torr, gas molecules are ionized in the electrical field between the specimen surface and the surrounding microscope parts through signal electrons and, to a certain extent, probe electrons. The gas provides a stable ion flux for a surface charge equalization if sufficient gas ions are provided.

A correlation of CL emissions from Penrith sandstone with elemental distributions obtained by simultaneous SEM-CL and EDS analysis

1995 ◽  
Vol 53 ◽  
pp. 392-393
Author(s):  
Paul J. Wright
Keyword(s):  
Optical Microscope ◽  
Electron Gun ◽  
High Electron ◽  
Collection System ◽  
Electron Hole ◽  
Depositional Processes ◽  
Eds Analysis ◽  
Distribution Mapping ◽  
Backscattered Electron ◽  
Electron Imaging

Most industrial and academic geologists are familiar with the beautiful red and orange cathodoluminescence colours produced by carbonate minerals in an optical microscope with a cold cathode electron gun attached. The cement stratigraphies interpreted from colour photographs have been widely used to determine the post depositional processes which have modified sedimentary rock textures.However to study quartzose materials high electron densities and kV's are necessary to stimulate sufficient emission. A scanning electron microscope with an optical collection system and monochromator provides an adequate tool and gives the advantage of providing secondary and backscattered electron imaging as well as elemental analysis and distribution mapping via standard EDS/WDS facilities.It has been known that the incorporation of many elements modify the characteristics of the CL emissions from geological materials. They do this by taking up positions between the valence and conduction band thus providing sites to assist in the recombination of electron hole pairs.

Cosmetology treatments on human hair: An SEM study

1996 ◽  
Vol 54 ◽  
pp. 940-941
Author(s):  
D.F. Bowling
Keyword(s):  
High School ◽  
High Resolution ◽  
Human Hair ◽  
Optical Microscope ◽  
Convincing Evidence ◽  
Brightness Contrast ◽  
Sem Study

High school cosmetology students study the methods and effects of various human hair treatments, including permanents, straightening, conditioning, coloring and cutting. Although they are provided with textbook examples of overtreatment and numerous hair disorders and diseases, a view of an individual hair at the high resolution offered by an SEM provides convincing evidence of the hair‘s altered structure. Magnifications up to 2000X provide dramatic differences in perspective. A good quality classroom optical microscope can be very informative at lower resolutions.Students in a cosmetology class are initially split into two groups. One group is taught basic controls on the SEM (focus, magnification, brightness, contrast, specimen X, Y, and Z axis movements). A healthy, untreated piece of hair is initially examined on the SEM The second group cements a piece of their own hair on a stub. The samples are dryed quickly using heat or vacuum while the groups trade places and activities.

Selective Corrosion of brazed joint between BNi-2 filler metal and stainless steel 316

1996 ◽  
Vol 54 ◽  
pp. 218-219
Author(s):  
H. S. Kim ◽  
R. U. Lee
Keyword(s):  
Stainless Steel ◽  
Filler Metal ◽  
Surface Preparation ◽  
Optical Microscope ◽  
Heating Element ◽  
Incomplete Fusion ◽  
Atmospheric Conditions ◽  
Leak Test ◽  
High Temperature Side ◽  
Inconel 600

A heating element/electrical conduit assembly used in the Orbiter Maneuvering System failed a leak test during a routine refurbishment inspection. The conduit, approximately 100 mm in length and 12 mm in diameter, was fabricated from two tubes and braze-joined with a sleeve. The tube on the high temperature side (heating element side) and the sleeve were made of Inconel 600 and the other tube was stainless steel (SS) 316. For the filler metal, a Ni-Cr-B brazing alloy per AWS BNi-2, was used. A Helium leak test spotted the leak located at the joint between the sleeve and SS 316 tubing. This joint was dissected, mounted in a plastic mold, polished, and examined with an optical microscope. Debonding of the brazed surfaces was noticed, more pronounced toward the sleeve end which was exposed to uncontrolled atmospheric conditions intermittently. Initially, lack of wetting was suspected, presumably caused by inadequate surface preparation or incomplete fusion of the filler metal. However, this postulation was later discarded based upon the following observations: (1) The angle of wetting between the fillet and tube was small, an indication of adequate wetting, (2) the fillet did not exhibit a globular microstructure which would be an indication of insufficient melting of the filler metal, and (3) debonding was intermittent toward the midsection of the sleeve.

On resolving fine periodic microstructures in the optical microscope

1989 ◽  
Vol 47 ◽  
pp. 364-365
Author(s):  
W.S. Putnam ◽  
C. Viney
Keyword(s):  
Liquid Crystalline ◽  
Numerical Aperture ◽  
Polarized Light ◽  
Normal Incidence ◽  
Optical Microscope ◽  
Angle Of Incidence ◽  
Resolution Limit ◽  
Crystalline Materials ◽  
Periodic Microstructures ◽  
Liquid Crystalline Materials

Many sheared liquid crystalline materials (fibers, films and moldings) exhibit a fine banded microstructure when observed in the polarized light microscope. In some cases, for example Kevlar® fiber, the periodicity is close to the resolution limit of even the highest numerical aperture objectives. The periodic microstructure reflects a non-uniform alignment of the constituent molecules, and consequently is an indication that the mechanical properties will be less than optimal. Thus it is necessary to obtain quality micrographs for characterization, which in turn requires that fine detail should contribute significantly to image formation.It is textbook knowledge that the resolution achievable with a given microscope objective (numerical aperture NA) and a given wavelength of light (λ) increases as the angle of incidence of light at the specimen surface is increased. Stated in terms of the Abbe resolution criterion, resolution improves from λ/NA to λ/2NA with increasing departure from normal incidence.

TEM study of lanthanum aluminate

1990 ◽  
Vol 48 (4) ◽  
pp. 1060-1061
Author(s):  
C.Y. Yang ◽  
Z.R. Huang ◽  
Y.Q. Zhou ◽  
C.Z. Li ◽  
W.H. Yang ◽  
...  
Keyword(s):  
Domain Boundary ◽  
Point Group ◽  
Optical Microscope ◽  
Dark Field ◽  
Zone Axis ◽  
Superconducting Film ◽  
Ion Milling ◽  
Lanthanum Aluminate ◽  
Ring Diameter ◽  
Diffraction Patterns

Lanthanum aluminate(LaAlO3) single crystal as a substrate for high Tc superconducting film has attracted attention recently. We report here a transmission electron microscopy(TEM) study of the crystal structure and phase transformation of LaAlO3 by using Philips EM420 and EM430 microscopes. Single crystals of LaAlO3 were investigated first by optical microscope. Stripe-shaped domains of mm size are clearly seen(Fig.1a), and 90° domain boundary is also obvious. TEM specimens were prepared by mechanical grinding and polishing followed by ion-milling.Fig.lb shows μm size stripe domains of LaAlO3. Convergent beam electron diffraction patterns (CBED) from single domain were taken.Fig. 2a and Fig. 2c are [001] zone axis patterns which show a 4mm symmetry, and the (200) dark field of this zone axis gives 2mm symmetry(fig.2b). Therefore the point group of this crystal is either 4/mmm or m3m. The projection of the first order Laue zone(FOLZ) reflections on zero layer (fig. 2c) shows that the unit cell is face centered. A tetragonal unit ceil is chosen, with a=0.532nm and c=0.753nm, c being determined from the FOLZ ring diameter.

New form of Transmission Cross Coefficient for High-Resolution Imaging

1990 ◽  
Vol 48 (1) ◽  
pp. 60-61
Author(s):  
Kazuo Ishizuka
Keyword(s):  
Electron Microscope ◽  
High Resolution ◽  
Transmission Function ◽  
Incident Beam ◽  
Optical Microscope ◽  
Strong Interactions ◽  
Small Range ◽  
Specimen Thickness ◽  
Beam Direction ◽  
Diffracted Waves

It is well known that taking into account spacial and temporal coherency of illumination as well as the wave aberration is important to interpret an image of a high-resolution electron microscope (HREM). This occues, because coherency of incident electrons restricts transmission of image information. Due to its large spherical and chromatic aberrations, the electron microscope requires higher coherency than the optical microscope. On an application of HREM for a strong scattering object, we have to estimate the contribution of the interference between the diffracted waves on an image formation. The contribution of each pair of diffracted waves may be properly represented by the transmission cross coefficients (TCC) between these waves. In this report, we will show an improved form of the TCC including second order derivatives, and compare it with the first order TCC.In the electron microscope the specimen is illuminated by quasi monochromatic electrons having a small range of illumination directions. Thus, the image intensity for each energy and each incident direction should be summed to give an intensity to be observed. However, this is a time consuming process, if the ranges of incident energy and/or illumination direction are large. To avoid this difficulty, we can use the TCC by assuming that a transmission function of the specimen does not depend on the incident beam direction. This is not always true, because dynamical scattering is important owing to strong interactions of electrons with the specimen. However, in the case of HREM, both the specimen thickness and the illumination angle should be small. Therefore we may neglect the dependency of the transmission function on the incident beam direction.

Role of Aluminium on the Microstructure and Corrosion Behaviour of Magnesium Prepared by Powder Metallurgy Method

2020 ◽  
Vol 17 (3) ◽  
pp. 8206-8213
Author(s):  
J. Alias
Keyword(s):  
Corrosion Resistance ◽  
Powder Metallurgy ◽  
Corrosion Behaviour ◽  
Corrosion Current ◽  
Optical Microscope ◽  
High Reactivity ◽  
Aluminium Content ◽  
Powder Metallurgy Method ◽  
X Ray Diffraction ◽  
Promising Development

Much research on magnesium (Mg) emphasises creating good corrosion resistance of magnesium, due to its high reactivity in most environments. In this study, powder metallurgy (PM) technique is used to produce Mg samples with a variation of aluminium (Al) composition. The effect of aluminium composition on the microstructure development, including the phase analysis was characterised by optical microscope (OM), scanning electron microscopy (SEM) and x-ray diffraction (XRD). The mechanical property of Mg sample was performed through Vickers microhardness. The results showed that the addition of aluminium in the synthesised Mg sample formed distribution of Al-rich phases of Mg17Al12, with 50 wt.% of aluminium content in the Mg sample exhibited larger fraction and distribution of Al-rich phases as compared to the 20 wt.% and 10 wt.% of aluminium content. The microhardness values were also increased at 20 wt.% and 50 wt.% of aluminium content, comparable to the standard microhardness value of the annealed Mg. A similar trend in corrosion resistance of the Mg immersed in 3.5 wt.% NaCl solution was observed. The corrosion behaviour was evaluated based on potentiodynamic polarisation behaviour. The corrosion current density, icorr, is observed to decrease with the increase of Al composition in the Mg sample, corresponding to the increase in corrosion resistance due to the formation of aluminium oxide layer on the Al-rich surface that acted as the corrosion barrier. Overall, the inclusion of aluminium in this study demonstrates the promising development of high corrosion resistant Mg alloys.

Sign in / Sign up

Export Citation Format

Share Document