Optimization of Nickel Removal from Electroless Plating Industry Wastewater using Response Surface Methodology

2014 ◽  
Vol 67 (4) ◽  
Author(s):  
Nor Azimah Ahmad ◽  
Mohd Ariffin Abu Hassan ◽  
Zainura Zainon Noor ◽  
Abdullahi Mohammed Evuti ◽  
Jibrin Mohammed Danlami
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Wastewater Treatment Plants ◽  
Oxygen Demand ◽  
Chemical Precipitation ◽  
Precipitation Process ◽  
Jar Test ◽  
Coagulant Dosage ◽  
Nickel Removal ◽  
Optimum Ph

Optimum pH and coagulant dosage for chemical precipitation in wastewater treatment plants is conventionally obtained through repeated jar test. In this research, optimization of the performance of polyacrylamide in the treatment of industrial wastewater was carried out using response surface methodology. The individual linear and quadratic effect of coagulant dosage and pH on the degree of removals of nickel, total suspended solids, Chemical Oxygen Demand and turbidity were investigated. The optimum pH and polyacrylamide dosage were found to be 10.5 and 1.6 ml/L respectively and the optimum percentage nickel removal was 96.9%. The model used in predicting the precipitation process gave a good fit with the experimental variables and hence the suitability of response surface methodology for the optimization of polyacrylamide performance.

scholarly journals Effective Chromium Adsorption From Aqueous Solutions and Tannery Wastewater Using Bimetallic Fe/Cu Nanoparticles: Response Surface Methodology and Artificial Neural Network

2021 ◽  
Vol 14 ◽  
pp. 117862212110281
Author(s):  
Ahmed S. Mahmoud ◽  
Nouran Y. Mohamed ◽  
Mohamed K. Mostafa ◽  
Mohamed S. Mahmoud
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Industrial Effluent ◽  
Oxygen Demand ◽  
Operating Conditions ◽  
Tannery Wastewater ◽  
P Value ◽  
Cu Nanoparticles ◽  
Artificial Neural ◽  
Cr Removal

Tannery industrial effluent is one of the most difficult wastewater types since it contains a huge concentration of organic, oil, and chrome (Cr). This study successfully prepared and applied bimetallic Fe/Cu nanoparticles (Fe/Cu NPs) for chrome removal. In the beginning, the Fe/Cu NPs was equilibrated by pure aqueous chrome solution at different operating conditions (lab scale), then the nanomaterial was applied in semi full scale. The operating conditions indicated that Fe/Cu NPs was able to adsorb 68% and 33% of Cr for initial concentrations of 1 and 9 mg/L, respectively. The removal occurred at pH 3 using 0.6 g/L Fe/Cu dose, stirring rate 200 r/min, contact time 20 min, and constant temperature 20 ± 2ºC. Adsorption isotherm proved that the Khan model is the most appropriate model for Cr removal using Fe/Cu NPs with the minimum error sum of 0.199. According to khan, the maximum uptakes was 20.5 mg/g Cr. Kinetic results proved that Pseudo Second Order mechanism with the least possible error of 0.098 indicated that the adsorption mechanism is chemisorption. Response surface methodology (RSM) equation was developed with a significant p-value = 0 to label the relations between Cr removal and different experimental parameters. Artificial neural networks (ANNs) were performed with a structure of 5-4-1 and the achieved results indicated that the effect of the dose is the most dominated variable for Cr removal. Application of Fe/Cu NPs in real tannery wastewater showed its ability to degrade and disinfect organic and biological contaminants in addition to chrome adsorption. The reduction in chemical oxygen demand (COD), biological oxygen demand (BOD), total suspended solids (TSS), total phosphorus (TP), total nitrogen (TN), Cr, hydrogen sulfide (H2S), and oil reached 61.5%, 49.5%, 44.8%, 100%, 38.9%, 96.3%, 88.7%, and 29.4%, respectively.

scholarly journals Optimization of Crude Oil and PAHs Degradation by Stenotrophomonas rhizophila KX082814 Strain through Response Surface Methodology Using Box-Behnken Design

2016 ◽  
Vol 2016 ◽  
pp. 1-13 ◽  
Author(s):  
Praveen Kumar Siddalingappa Virupakshappa ◽  
Manjunatha Bukkambudhi Krishnaswamy ◽  
Gaurav Mishra ◽  
Mohammed Ameenuddin Mehkri
Keyword(s):  
Response Surface Methodology ◽  
Crude Oil ◽  
Response Surface ◽  
Oxygen Demand ◽  
Inoculum Size ◽  
Coefficient Of Determination ◽  
Oil Removal ◽  
Box Behnken Design ◽  
Stenotrophomonas Rhizophila ◽  
Crude Oil Removal

The present paper describes the process optimization study for crude oil degradation which is a continuation of our earlier work on hydrocarbon degradation study of the isolate Stenotrophomonas rhizophila (PM-1) with GenBank accession number KX082814. Response Surface Methodology with Box-Behnken Design was used to optimize the process wherein temperature, pH, salinity, and inoculum size (at three levels) were used as independent variables and Total Petroleum Hydrocarbon, Biological Oxygen Demand, and Chemical Oxygen Demand of crude oil and PAHs as dependent variables (response). The statistical analysis, via ANOVA, showed coefficient of determination R2 as 0.7678 with statistically significant P value 0.0163 fitting in second-order quadratic regression model for crude oil removal. The predicted optimum parameters, namely, temperature, pH, salinity, and inoculum size, were found to be 32.5°C, 9, 12.5, and 12.5 mL, respectively. At this optimum condition, the observed and predicted PAHs and crude oil removal were found to be 71.82% and 79.53% in validation experiments, respectively. The % TPH results correlate with GC/MS studies, BOD, COD, and TPC. The validation of numerical optimization was done through GC/MS studies and   % removal of crude oil.

scholarly journals Response surface methodology approach for the optimisation of adsorption of hydrolysed polyacrylamide from polymer-flooding wastewater onto steel slag: a good option of waste mitigation

2017 ◽  
Vol 76 (4) ◽  
pp. 776-784 ◽  
Author(s):  
Mijia Zhu ◽  
Jun Yao ◽  
Zhonghai Qin ◽  
Luning Lian ◽  
Chi Zhang
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Removal Efficiency ◽  
Contact Time ◽  
Interactive Effect ◽  
Steel Slag ◽  
Oxygen Demand ◽  
Polymer Flooding ◽  
High Concentration ◽  
Adsorbent Dosage

Wastewater produced from polymer flooding in oil production features high viscosity and chemical oxygen demand because of the residue of high-concentration polymer hydrolysed polyacrylamide (HPAM). In this study, steel slag, a waste from steel manufacturing, was studied as a low-cost adsorbent for HPAM in wastewater. Optimisation of HPAM adsorption by steel slag was performed with a central composite design under response surface methodology (RSM). Results showed that the maximum removal efficiency of 89.31% was obtained at an adsorbent dosage of 105.2 g/L, contact time of 95.4 min and pH of 5.6. These data were strongly correlated with the experimental values of the RSM model. Single and interactive effect analysis showed that HPAM removal efficiency increased with increasing adsorbent dosage and contact time. Efficiency increased when pH was increased from 2.6 to 5.6 and subsequently decreased from 5.6 to 9.3. It was observed that removal efficiency significantly increased (from 0% to 86.1%) at the initial stage (from 0 min to 60 min) and increased gradually after 60 min with an adsorbent dosage of 105.2 g/L, pH of 5.6. The adsorption kinetics was well correlated with the pseudo-second-order equation. Removal of HPAM from the studied water samples indicated that steel slag can be utilised for the pre-treatment of polymer-flooding wastewater.

scholarly journals Optimization of Antimony Removal by Coagulation-Flocculation-Sedimentation Process Using Response Surface Methodology

Processes ◽  
2021 ◽  
Vol 9 (1) ◽  
pp. 117
Author(s):  
Muhammad Ali Inam ◽  
Rizwan Khan ◽  
Ick Tae Yeom ◽  
Abdul Salam Buller ◽  
Muhammad Akram ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Environmental Water ◽  
High Dose ◽  
Operating Variables ◽  
Model Response ◽  
Aqueous Environments ◽  
Optimum Ph ◽  
Potential Risks ◽  
Good Agreement

Coprecipitation-adsorption plays a significant role during coagulation-flocculation-sedimentation (C/F/S) of antimony (Sb) in water. This work uses a Box–Behnken statistical experiment design (BBD) and response surface methodology (RSM) to investigate the effects of major operating variables such as initial Sb(III, V) concentration (100–1000 µg/L), ferric chloride (FC) dose (5–50 mg/L), and pH (4–10) on redox Sb species. Experimental data of Sb(III, V) removal were used to determine response function coefficients. The model response value (Sb removal) showed good agreement with the experimental results. FC showed promising coagulation behavior of both Sb species under optimum pH (6.5–7.5) due to its high affinity towards Sb species and low residual Fe concentration. However, a high dose of 50 mg/L of FC is required for the maximum (88–93%) removal of Sb(V), but also for the highest (92–98%) removal of low initial concentrations of Sb(III). Furthermore, BBD and RSM were found to be reliable and feasible for determining the optimum conditions for Sb removal from environmental water samples by a C/F/S process. This work may contribute to a better understanding and prediction of the C/F/S behavior of Sb(III, V) species in aqueous environments, to reduce potential risks to humans.

scholarly journals Optimization of Coagulation-Flocculation Process of Landfill Leachate by Tin (IV) Chloride Using Response Surface Methodology

2019 ◽  
Vol 6 (1) ◽  
pp. 41-48 ◽  
Author(s):  
Abdul Aziz Hamidi ◽  
Syed Zainal Sharifah Farah Fariza ◽  
Alazaiza Motasem Y.D
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Removal Efficiency ◽  
Landfill Leachate ◽  
Chemical Properties ◽  
Oxygen Demand ◽  
Statistical Design ◽  
Water Infiltration ◽  
Flocculation Process ◽  
Maximum Removal

Landfill leachate is highly polluted and generated as a result of water infiltration through solid waste produced domestically and industrially. This study investigated the applicability of the response surface methodology (RSM) to optimize the removal performances of chemical oxygen demand (COD), color, and suspended solids (SS) from landfill leachate by coagulation process using Tin tetrachloride pentahydrate. The leachate samples were collected from Alor Pongsu Landfill (APLS) in Perak, Malaysia. Before starting the experiments, general characterization was carried out for raw leachate samples to investigate their physical and chemical properties. The effects of the dosage and pH of SnCl4 on the removal performances were evaluated as well. An ideal experimental design was performed based on the central composite design (CCD) by RSM. In addition, this RSM was used to evaluate the effects of process variables and their interaction toward the attainment of their optimum conditions. The statistical design of the experiments and data analysis was resolved using the Design-Expert software. Further, the range of coagulant dosage and pH was selected based on a batch study which was conducted at 13000 mg/L to 17000 mg/L of SnCl4 and pH ranged from 6 to 10. The results showed that the optimum pH and dosage of SnCl4 were 7.17 and 15 g/L, respectively, where the maximum removal efficiency was 67.7% for COD and 100% for color and SS. The results were in agreement with the experimental data with a maximum removal efficiency of 67.84 %, 98.6 %, and 99.3%, for COD, color, and SS, respectively. Overall, this study verified that the RSM method was viable for optimizing the operational condition of the coagulation-flocculation process.

scholarly journals Taguchi Method and Response Surface Methodology in the Treatment of Highly Contaminated Tannery Wastewater Using Commercial Potassium Ferrate

Materials ◽  
2019 ◽  
Vol 12 (22) ◽  
pp. 3784 ◽  
Author(s):  
Violetta Kozik ◽  
Krzysztof Barbusinski ◽  
Maciej Thomas ◽  
Agnieszka Sroda ◽  
Josef Jampilek ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Organic Carbon ◽  
Taguchi Method ◽  
Chemical Oxygen Demand ◽  
Total Organic Carbon ◽  
Response Surface ◽  
Suspended Solids ◽  
Oxygen Demand ◽  
Tannery Wastewater ◽  
Potassium Ferrate

The potential implementation of Envifer®, a commercial product containing potassium ferrate (40.1% K2FeO4), for the purification of highly contaminated tannery wastewater from leather dyeing processes was proposed. The employment of the Taguchi method for optimization of experiments allowed the discoloration (98.4%), chemical oxygen demand (77.2%), total organic carbon (75.7%), and suspended solids (96.9%) values to be lowered using 1.200 g/L K2FeO4 at pH 3 within 9 min. The application of the central composite design (CCD) and the response surface methodology (RSM) with the use of 1.400 g/L K2FeO4 at pH 4.5 diminished the discoloration, the chemical oxygen demand, the total organic carbon, and suspended solids within 9 min. The Taguchi method is suitable for the initial implementation, while the RSM is superior for the extended optimization of wastewater treatment processes.

Optimisation of chemical oxygen demand removal from landfill leachate by sonocatalytic degradation in the presence of cupric oxide nanoparticles

2017 ◽  
Vol 35 (6) ◽  
pp. 636-646 ◽  
Author(s):  
Paria Amirian ◽  
Edris Bazrafshan ◽  
Abolfazl Payandeh
Keyword(s):  
Response Surface Methodology ◽  
Chemical Oxygen Demand ◽  
Response Surface ◽  
Landfill Leachate ◽  
Cupric Oxide ◽  
Oxygen Demand ◽  
Oxide Nanoparticles ◽  
Ultrasonic Frequency ◽  
Optimum Conditions ◽  
Cupric Oxide Nanoparticles

Leachate is the liquid formed when waste breaks down in the landfill and water filters through that waste. This liquid is very toxic and can pollute the land, ground water, and water resources. In most countries, it is mandatory for landfills to be protected against leachate. In addition to all other harms to the environment, disposal of raw landfill leachate can be a major source of hazard to closed water bodies. Hence, treatment of landfill leachate is considered an essential step prior to its discharge from source. This article describes the sonocatalytic degradation of chemical oxygen demand in landfill leachate using cupric oxide nanoparticles as sonocatalyst (cupric oxide/ultrasonic) and aims to establish this method as an effective alternative to currently used approaches. An ideal experimental design was carried out based on a central composite design with response surface methodology. The response surface methodology was used to evaluate the effect of process variables including pH values (3, 7, 11), cupric oxide nanoparticles dose (0.02, 0.035, 0.05 g), reaction time (10, 35, 60 minutes), ultrasonic frequency (35, 37, 130 KHz), and their interaction towards the attainment of their optimum conditions. The derived second-order model, including both significant linear and quadratic terms, seemed to be adequate in predicting responses (R2 = 0.9684 and prediction R2 = 0.9581). The optimum conditions for the maximum chemical oxygen demand sonocatalytic degradation of 85.82% were found to be pH 6.9, cupric oxide nanoparticles dosage of 0.05 gr L−1, and the ultrasonic frequency of 130 kHz at a contact time of 10 min.

Phosphorus recovery from synthetic swine wastewater by chemical precipitation using response surface methodology

2010 ◽  
Vol 176 (1-3) ◽  
pp. 1083-1088 ◽  
Author(s):  
Zhi-Long Ye ◽  
Shao-Hua Chen ◽  
Shu-Mei Wang ◽  
Li-Feng Lin ◽  
Yi-Jun Yan ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Chemical Precipitation ◽  
Phosphorus Recovery ◽  
Swine Wastewater
Sign in / Sign up

Export Citation Format

Share Document