scholarly journals EFFECT OF TIP CLEARANCE ON THE FLOW FIELD OF THE MIXED FLOW TURBOCHARGER TURBINE

2017 ◽  
Vol 79 (7-3) ◽  
Author(s):  
M. S. Kamarudin ◽  
M. Zulkeflee ◽  
M. H. Padzillah
Keyword(s):  
Flow Field ◽  
Combustion Engine ◽  
Velocity Ratio ◽  
Leading Edge ◽  
Tip Clearance ◽  
Optimum Operating ◽  
Low Velocity ◽  
Mixed Flow ◽  
Optimum Operating Condition ◽  
Design Speed

Turbocharger is a device comprising mainly of a turbine and a compressor. The demand of turbocharger in the automotive industry increases as it significantly enhances the output power of an Internal Combustion Engine and reduces emission. The use of mixed flow turbine to replace the conventional radial turbine gives better impact since the turbine transient response increases and operates more efficiently at low velocity ratio. The flow behaviour inside the turbine affects the torque generation by the turbine. It is necessary for the turbine to have a specified clearance between the rotor tip and the casing of the turbomachine. This undoubtedly will contribute to clearance loss and mixing of leaked flow which produce disturbance to the exhaust flow. In order to investigate this effect, the validated Computational Fluid Dynamics method is chosen in order to replicate the flow field inside the mixed flow turbine. The simulation is carried out at the optimum operating condition which is at turbine total-to-static efficiency of 79% with inlet mass flow rate of 0.5kg/s. The flow inside the passage is plotted into pressure and velocity contours which are compared at 50% (30000rpm) and 80% (48000rpm) of the turbine design speed. The comparison between having 0% (no leakage) and 3% shroud tip clearance are then compared. Through the analysis, it is suggested that clearance leakage and flow separation cause disruption to the desirable uniform flow inside the turbine passage. The presence of Coriolis effect that resists the clearance leakage flow only at near leading edge of the rotor is observed. Furthermore, a low pressure region is perceived at rotor hub which absent in the radial flow turbine. These factors eventually reduce the performances of the actual turbine.

FLOW FIELD ANALYSIS OF AN AUTOMOTIVE MIXED FLOW TURBOCHARGER TURBINE

2015 ◽  
Vol 77 (8) ◽  
Author(s):  
M. H. Padzillah ◽  
S. Rajoo ◽  
R. F. Martinez-Botas
Keyword(s):  
Optimum Condition ◽  
Flow Field ◽  
Internal Combustion Engines ◽  
Pressure Ratio ◽  
Leading Edge ◽  
Tip Clearance ◽  
Field Analysis ◽  
Turbine Stage ◽  
Mixed Flow ◽  
Geometrical Properties

Traditionally, the turbocharger has been an essential tool to boost the engine power especially the diesel engine. However, in recent years it is seen as an enabling technology for engine downsizing of all internal combustion engines. The use of mixed flow turbine as replacement for radial turbine in an automotive turbocharger has been proven to deliver better efficiency at high loading conditions. Furthermore, the use vanes that match the geometrical properties at the turbine leading edge could further increase its performance. However, improvement on the overall turbocharger performance is currently limited due to lack of understanding on the flow feature within the turbine stage. Therefore, the use of validated Computational Fluid Dynamics (CFD) in resolving this issue is necessary. This research attempts to provide description of flow field within the turbocharger turbine stage by plotting velocity and pressure contours at different planes. To achieve this aim, a numerical model of a full stage turbocharger turbine operating at 30000rpm under its optimum condition (pressure ratio of 1.3) is developed and validated. Results indicated strong tip-clearance flow downstream of the turbine mid-chord. Evidence of flow separations at the turbine leading edge are also seen despite turbine operating at its optimum condition.

Influence of different blade numbers on the performance of “saddle zone” in a mixed flow pump

2021 ◽  
pp. 095765092110460
Author(s):  
Leilei Ji ◽  
Wei Li ◽  
Weidong Shi ◽  
Fei Tian ◽  
Shuo Li ◽  
...  
Keyword(s):  
Flow Field ◽  
Leading Edge ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Mixed Flow ◽  
Impeller Blade ◽  
Flow Angle ◽  
Tip Leakage ◽  
Vorticity Transport ◽  
Flow Pump

In order to study the effect of different numbers of impeller blades on the performance of mixed-flow pump “saddle zone”, the external characteristic test and numerical simulation of mixed-flow pumps with three different impeller blade numbers were carried out. Based on high-precision numerical prediction, the internal flow field and tip leakage flow field of mixed flow pump under design conditions and stall conditions are investigated. By studying the vorticity transport in the stall flow field, the specific location of the high loss area inside the mixed flow pump impeller with different numbers of blades is located. The research results show that the increase in the number of impeller blades improve the pump head and efficiency under design conditions. Compared to the 4-blade impeller, the head and efficiency of the 5-blade impeller are increased by 5.4% and 21.9% respectively. However, the increase in the number of blades also leads to the widening of the “saddle area” of the mixed-flow pump, which leads to the early occurrence of stall and increases the instability of the mixed-flow pump. As the mixed-flow pump enters the stall condition, the inlet of the mixed-flow pump has a spiral swirl structure near the end wall for different blade numbers, but the depth and range of the swirling flow are different due to the change in the number of blades. At the same time, the change in the number of blades also makes the flow angle at 75% span change significantly, but the flow angle at 95% span is not much different because the tip leakage flow recirculates at the leading edge. Through the analysis of the vorticity transport results in the impeller with different numbers of blades, it is found that the reasons for the increase in the values of the vorticity transport in the stall condition are mainly impacted by the swirl flow at the impeller inlet, the tip leakage flow at the leading edge and the increased unsteady flow structures.

Influences of Tip Leakage Flows Discharged From Main and Splitter Blades on Flow Field in Transonic Centrifugal Compressor Stage

2018 ◽  
Author(s):  
Masanao Kaneko ◽  
Hoshio Tsujita
Keyword(s):  
Flow Field ◽  
Centrifugal Compressor ◽  
Leading Edge ◽  
Tip Clearance ◽  
Blade Loading ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Leakage Flows ◽  
Transonic Centrifugal Compressor ◽  
Tip Leakage Flows

A transonic centrifugal compressor impeller is generally composed of the main and the splitter blades which are different in chord length. As a result, the tip leakage flows from the main and the splitter blades interact with each other and then complicate the flow field in the compressor. In this study, in order to clarify the individual influences of these leakage flows on the flow field in the transonic centrifugal compressor stage at near-choke to near-stall condition, the flows in the compressor at four conditions prescribed by the presence and the absence of the tip clearances were analyzed numerically. The computed results clarified the following noticeable phenomena. The tip clearance of the main blade induces the tip leakage vortex from the leading edge of the main blade. This vortex decreases the blade loading of the main blade to the negative value by the increase of the flow acceleration along the suction surface of the splitter blade, and consequently induces the tip leakage vortex caused by the negative blade loading of the main blade at any operating points. These phenomena decline the impeller efficiency. On the other hand, the tip clearance of the splitter blade decreases the afore mentioned acceleration by the formation of the tip leakage vortex from the leading edge of the splitter blade and the decrease of the incidence angle for the splitter blade caused by the suction of the flow into the tip clearance. These phenomena reduce the loss generated by the negative blade loading of the main blade and consequently reduce the decline of the impeller efficiency. Moreover, the tip clearances enlarge the flow separation around the diffuser inlet and then decline the diffuser performance independently of the operating points.

Non-Uniform Two-Phase Flow of Supercritical Carbon Dioxide Centrifugal Compressor

2020 ◽  
Author(s):  
Wenrui Bao ◽  
Ce Yang ◽  
Li Fu ◽  
Changmao Yang ◽  
Lucheng Ji
Keyword(s):  
Carbon Dioxide ◽  
Supercritical Carbon Dioxide ◽  
Flow Field ◽  
Centrifugal Compressor ◽  
Static Pressure ◽  
Leading Edge ◽  
Phase Region ◽  
Tip Clearance ◽  
Two Phase ◽  
Supercritical Carbon

Abstract An asymmetric structure of volute in a supercritical carbon dioxide centrifugal compressor induces a non-uniform circumferential distribution of the upstream flow field, which inevitably affects the formation of a two-phase region of carbon dioxide in an impeller. In this work, unsteady simulations for centrifugal compressors were conducted. First, the influence of low static strip induced by low static pressure near volute tongue on the impeller flow field was presented. Then, the non-uniform flow field distribution in the impeller passages and flow characteristics of the passages at the impeller inlet were obtained. Finally, the two-phase regions in the impeller were presented. The results demonstrate that for a centrifugal compressor with volute, the two-phase region appears not only on the suction surface of the leading edge of the blade, but also in some impeller passages, on the pressure surface of the blade near the leading edge, and in the leading edge and mid-chord of tip clearance, under the design conditions. The low static pressure strip induced by the volute leads to a high-speed region in the impeller passages where the temperature and pressure of supercritical carbon dioxide fall below the critical point and carbon dioxide enters the two-phase region. Meanwhile, the static pressure on the blade surface is distorted under the influence of a high-speed region in the passages, resulting in the formation of a two-phase region at the tip clearance. The flow distortion of passages at the impeller inlet results in the appearance of two-phase regions on the both sides of leading edge of the blade. The dryness on the suction side of the blade leading edge and the leading edge of the tip clearance is lower, which indicated that the proportion of liquid-phase carbon dioxide is higher in these two-phase regions.

A Numerical Study of Inlet Geometry for a Low Inertia Mixed Flow Turbocharger Turbine

2014 ◽  
Author(s):  
Thomas M. Leonard ◽  
Stephen Spence ◽  
Juliana Early ◽  
Dietmar Filsinger
Keyword(s):  
High Speed ◽  
Numerical Study ◽  
Velocity Ratio ◽  
Cone Angle ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Transient Performance ◽  
Blade Angle ◽  
Low Velocity ◽  
Mixed Flow

Mixed flow turbines can offer improvements over typical radial turbines used in automotive turbochargers, with regards to transient performance and low velocity ratio efficiency. Turbine rotor mass dominates the rotating inertia of the turbocharger, and any reductions of mass in the outer radii of the wheel, including the rotor back-disk, can significantly reduce this inertia and improve the acceleration of the assembly. Off-design, low velocity ratio conditions are typified by highly tangential flow at the rotor inlet and a non-zero inlet blade angle is preferred for such operating conditions. This is achievable in a Mixed Flow Turbine without increasing bending stresses within the rotor blade, which is beneficial in high speed and high inlet temperature turbine design. A range of mixed flow turbine rotors was designed with varying cone angle and inlet blade angle and each was assessed at a number of operating points. These rotors were based on an existing radial flow turbine, and both the hub and shroud contours and exducer geometry were maintained. The inertia of each rotor was also considered. The results indicated that there was a trade-off between efficiency and inertia for the rotors and certain designs may be beneficial for the transient performance of downsized, turbocharged engines.

scholarly journals Effects of a Nonuniform Tip Clearance Profile on the Performance and Flow Field in a Centrifugal Compressor

2012 ◽  
Vol 2012 ◽  
pp. 1-11 ◽  
Author(s):  
Yohan Jung ◽  
Minsuk Choi ◽  
Seonghwan Oh ◽  
Jehyun Baek
Keyword(s):  
Flow Field ◽  
Centrifugal Compressor ◽  
Diffusion Processes ◽  
Leading Edge ◽  
Tip Clearance ◽  
Computational Results ◽  
Vaneless Diffuser ◽  
Trailing Edge ◽  
Flow Simulations ◽  
Compressor Performance

This paper presents a numerical investigation of the effects of a nonuniform tip clearance profile on the performance and flow field in a centrifugal compressor with a vaneless diffuser. This study focuses in particular on the magnitude and location of the wake. Six impellers with different tip clearance profiles were tested in the flow simulations. The accuracy of the numerical simulations was assessed by comparing the experimental data with the computational results for a system characterized by the original tip clearance. Although the performance improved for low tip clearances, a low tip clearance at the trailing edge improved the compressor performance more significantly than a low tip clearance at the leading edge. The flow field calculated for a system characterized by a low tip clearance at the trailing edge produced a more uniform velocity distribution both in the circumferential and in the axial directions at the impeller exit because the wake magnitude was reduced. As a consequence, this impeller provided a better potential for diffusion processes inside a vaneless diffuser.

Mixed Flow Turbines: Inlet and Exit Flow Under Steady and Pulsating Conditions

2000 ◽  
Author(s):  
N. Karamanis ◽  
R. F. Martinez-Botas ◽  
C. C. Su
Keyword(s):  
High Speed ◽  
Pulse Propagation ◽  
Combustion Engine ◽  
Pressure Ratio ◽  
Flow Characteristics ◽  
Leading Edge ◽  
Mixed Flow ◽  
Flow Measurements ◽  
Flow Angle ◽  
Isentropic Efficiency

The performance and detailed flow characteristics of a high pressure ratio mixed flow turbine has been investigated under steady and pulsating flow conditions. The rotor has been designed to have a nominal constant incidence (based on free vortex flow in the volute) and it is for use in an automotive high speed diesel turbocharger. The results indicated a departure from the quasi-steady analysis commonly used in turbocharger turbine design. The pulsations from the engine have been followed through the inlet pipe and around the volute; the pulse has been shown to propagate close to the speed of sound and not according to the bulk flow velocity as stated by some researchers. The flow entering and exiting the blades has been quantified by a laser Doppler velocimetry system. The measurements were performed at a plane 3.0 mm ahead of the rotor leading edge and 9.5 mm behind the rotor trailing edge. The turbine test conditions corresponded to the peak efficiency point at 29,400 and 41,300 rpm. The results were resolved in a blade-to-blade sense to examine in greater detail the nature of the flow at turbocharger representative conditions. A correlation between the combined effects of incidence and exit flow angle with the isentropic efficiency has been shown. The unsteady flow characteristics have been investigated at two flow pulse frequencies, corresponding to internal combustion engine speeds of 1600 and 2400 rpm. Four measurement planes have been investigated: one in the pipe feeding the volute, two in the volute (40° and 130° downstream of the tongue) and one at the exit of the turbine. The pulse propagation at these planes has been investigated; the effect of the different planes on the evaluation of the unsteady isentropic efficiency is shown to be significant. Overall, the unsteady performance efficiency results indicated a significant departure from the corresponding steady performance, in accordance with the inlet and exit flow measurements.

Mechanism of affecting the performance and internal flow field of an axial flow subsonic compressor with self-recirculation casing treatment

2020 ◽  
pp. 095441002094267
Author(s):  
Hao G Zhang ◽  
Fei Y Dong ◽  
Wei Wang ◽  
Wu L Chu ◽  
Song Yan
Keyword(s):  
Flow Field ◽  
Axial Flow ◽  
Internal Flow ◽  
Leading Edge ◽  
Tip Clearance ◽  
Stall Margin ◽  
Casing Treatment ◽  
Leakage Flows ◽  
Blade Tip ◽  
Compressor Performance

This investigation aims to understand the mechanisms of affecting the axial flow compressor performance and internal flow field with the application of self-recirculation casing treatment. Besides, the potentiality of further enhancing the compressor performance and stability by optimizing the geometric structure of self-recirculation casing treatment is discussed in detail. The results show that self-recirculation casing treatment generates about 7.06, 7.89% stall margin improvements in the experiment and full-annulus unsteady calculation, respectively. Moreover, the compressor total pressure and isentropic efficiency are improved among most of operating points, and the experimental and calculated compressor peak efficiencies are increased by 0.7% and 0.6%, respectively. The comparisons between baseline shroud and self-recirculation casing treatment show that the flow conditions of the compressor rotor inlet upstream are improved well with self-recirculation casing treatment, and the degree of the pressure enhancement in the blade top passage for self-recirculation casing treatment is higher than that for baseline. Further, self-recirculation casing treatment can restrain the leading edge-spilled flows made by the blade tip clearance leakage flows and weaken the blade tip passage blockage. Hence, the flow loss near the rotor top passage is reduced after the application of self-recirculation casing treatment. The rotor performance and stability for self-recirculation casing treatment are greater than those for baseline. The flow-field analyses also indicate that the adverse effects caused by the clearance leakage flows of the blades tip rear are greater than those made by the clearance leakage flows of the blades leading edge. When one injecting part of self-recirculation casing treatment is aligned with the inlet of one blade tip passage, the flow-field quality in the passage is not the best among all the passages between two adjacent injecting parts of self-recirculation casing treatment. Further, the flow-field analyses also indicate that the effect of the relative position between the blade and self-recirculation casing treatment on the flows in the self-recirculation casing treatment may be ignored during the optimization of the recirculating loop configuration.

Comparative Study on Tip Clearance Flow Fields in Two Types of Transonic Centrifugal Compressor Impeller With Splitter Blades

2010 ◽  
Author(s):  
Kazutoyo Yamada ◽  
Yusuke Tamagawa ◽  
Hisataka Fukushima ◽  
Masato Furukawa ◽  
Seiichi Ibaraki ◽  
...  
Keyword(s):  
Leading Edge ◽  
Tip Clearance ◽  
Low Velocity ◽  
Blade Loading ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Transonic Centrifugal Compressor ◽  
Compressor Impeller ◽  
Clearance Flow ◽  
Velocity Region

Two types of transonic centrifugal compressor impeller with splitter blades, which are different in blade count, have been investigated in this study. RANS (Reynolds-Averaged Navier-Stokes) simulations were carried out for several operating conditions to clarify differences in aerodynamic performance characteristic and tip clearance flow field between the two compressors. The simulation shows that basically similar flow events happen in both compressors. A low velocity region is generated near the tip at low flow rate conditions, which results from an expansion of the tip leakage vortex. The low velocity region expands as the flow rate is decreased, and interacts with the pressure surface of the splitter blade near the leading edge. This causes a descent of the blade loading near the tip of the leading edge, and an accumulation of high entropy fluid near the casing-suction corner. Moreover, the tip clearance flow spills ahead of the leading edge of the splitter blade at near stall condition, and eventually the spillage happens at the full blade at stall condition. However, the major difference in solidity influences tip clearance flow/blade interaction, which leads to changes in the performance characteristics. In the impeller with low solidity, the tip leakage vortex breaks down with a large blockage effect because of high blade loading at the tip, which decreases the pressure ratio. The impeller with high solidity is subject to the spillage, which results in an early and large-scale stall that decreases the efficiency.

Sign in / Sign up

Export Citation Format

Share Document