Mixed Flow Turbines: Inlet and Exit Flow Under Steady and Pulsating Conditions

2000 ◽  
Author(s):  
N. Karamanis ◽  
R. F. Martinez-Botas ◽  
C. C. Su
Keyword(s):  
High Speed ◽  
Pulse Propagation ◽  
Combustion Engine ◽  
Pressure Ratio ◽  
Flow Characteristics ◽  
Leading Edge ◽  
Mixed Flow ◽  
Flow Measurements ◽  
Flow Angle ◽  
Isentropic Efficiency

The performance and detailed flow characteristics of a high pressure ratio mixed flow turbine has been investigated under steady and pulsating flow conditions. The rotor has been designed to have a nominal constant incidence (based on free vortex flow in the volute) and it is for use in an automotive high speed diesel turbocharger. The results indicated a departure from the quasi-steady analysis commonly used in turbocharger turbine design. The pulsations from the engine have been followed through the inlet pipe and around the volute; the pulse has been shown to propagate close to the speed of sound and not according to the bulk flow velocity as stated by some researchers. The flow entering and exiting the blades has been quantified by a laser Doppler velocimetry system. The measurements were performed at a plane 3.0 mm ahead of the rotor leading edge and 9.5 mm behind the rotor trailing edge. The turbine test conditions corresponded to the peak efficiency point at 29,400 and 41,300 rpm. The results were resolved in a blade-to-blade sense to examine in greater detail the nature of the flow at turbocharger representative conditions. A correlation between the combined effects of incidence and exit flow angle with the isentropic efficiency has been shown. The unsteady flow characteristics have been investigated at two flow pulse frequencies, corresponding to internal combustion engine speeds of 1600 and 2400 rpm. Four measurement planes have been investigated: one in the pipe feeding the volute, two in the volute (40° and 130° downstream of the tongue) and one at the exit of the turbine. The pulse propagation at these planes has been investigated; the effect of the different planes on the evaluation of the unsteady isentropic efficiency is shown to be significant. Overall, the unsteady performance efficiency results indicated a significant departure from the corresponding steady performance, in accordance with the inlet and exit flow measurements.

Mixed Flow Turbines: Inlet and Exit Flow Under Steady and Pulsating Conditions

2000 ◽  
Vol 123 (2) ◽  
pp. 359-371 ◽  
Author(s):  
N. Karamanis ◽  
R. F. Martinez-Botas ◽  
C. C. Su
Keyword(s):  
High Speed ◽  
Pulse Propagation ◽  
Combustion Engine ◽  
Pressure Ratio ◽  
Flow Characteristics ◽  
Leading Edge ◽  
Mixed Flow ◽  
Flow Measurements ◽  
Flow Angle ◽  
Isentropic Efficiency

The performance and detailed flow characteristics of a high pressure ratio mixed flow turbine has been investigated under steady and pulsating flow conditions. The rotor has been designed to have a nominal constant incidence (based on free vortex flow in the volute) and it is for use in an automotive high speed diesel turbocharger. The results indicated a departure from the quasi-steady analysis commonly used in turbocharger turbine design. The pulsations from the engine have been followed through the inlet pipe and around the volute; the pulse has been shown to propagate close to the speed of sound and not according to the bulk flow velocity as stated by some researchers. The flow entering and exiting the blades has been quantified by a laser Doppler velocimetry system. The measurements were performed at a plane 3.0 mm ahead of the rotor leading edge and 9.5 mm behind the rotor trailing edge. The turbine test conditions corresponded to the peak efficiency point at 29,400 and 41,300 rpm. The results were resolved in a blade-to-blade sense to examine in greater detail the nature of the flow at turbocharger representative conditions. A correlation between the combined effects of incidence and exit flow angle with the isentropic efficiency has been shown. The unsteady flow characteristics have been investigated at two flow pulse frequencies, corresponding to internal combustion engine speeds of 1600 and 2400 rpm. Four measurement planes have been investigated: one in the pipe feeding the volute, two in the volute (40 deg and 130 deg downstream of the tongue) and one at the exit of the turbine. The pulse propagation at these planes has been investigated; the effect of the different planes on the evaluation of the unsteady isentropic efficiency is shown to be significant. Overall, the unsteady performance efficiency results indicated a significant departure from the corresponding steady performance, in accordance with the inlet and exit flow measurements.

Investigation Into the Impact of Span-Wise Flow Distribution on the Performance of a Mixed Flow Turbine

2018 ◽  
Author(s):  
Samuel P. Lee ◽  
Simon M. Barrans ◽  
Martyn L. Jupp ◽  
Ambrose K. Nickson
Keyword(s):  
Flow Characteristics ◽  
Axial Flow ◽  
Engine Performance ◽  
Flow Distribution ◽  
Leading Edge ◽  
Vital Role ◽  
Mixed Flow ◽  
Flow Angle ◽  
Inlet Conditions ◽  
The Impact

Current trends in the automotive industry towards engine downsizing means turbocharging now plays a vital role in engine performance. A turbocharger increases charge air density using a turbine to extract waste energy from the exhaust gas to drive a compressor. Most turbocharger applications employ a radial inflow turbine. However, to ensure radial stacking of the blade fibers and avoid excessive blade stresses, the inlet blade angle must remain at zero degrees. Alternately, mixed flow turbines can offer non-zero blade angles while maintaining radial stacking of the blade fibers. The additional freedom to manipulate the blade leading edge and varying tip speed allow for varying leading edge incidence in the span-wise direction. Furthermore, the flow development in the volute does not necessarily lead to uniform inlet conditions. The current paper investigates the performance of a mixed flow rotor passage under a range of span-wise flow distributions including that produced by a turbine volute. Initial unsteady pulsating simulations were conducted and the volute exit flows extracted. These distributions were then applied as boundary conditions to a single passage model. All simulations were carried out at a constant MFP and average leading edge relative flow angle. It was observed that the different inlet flow distributions resulted in marked difference in passage flow characteristics. A 2.17% variation was observed between cases in the radial passage. A tilted passage was also included providing an increased axial flow component at the inlet. This passage was found to result in greater swallowing capacity when compared to that of the radial passage.

Inlet and Exit Flow Characteristics of Mixed Flow Turbines

1998 ◽  
Author(s):  
C. Arcoumanis ◽  
R. F. Martinez-Botas ◽  
J. M. Nouri ◽  
C. C. Su
Keyword(s):  
Incidence Angle ◽  
Pressure Ratio ◽  
Flow Characteristics ◽  
Expansion Ratio ◽  
Superior Performance ◽  
Mixed Flow ◽  
Flow Angle ◽  
High Pressure Ratio ◽  
Swirl Angle ◽  
Design Speed

The steady performance of mainly two high pressure ratio mixed flow turbines for an automotive turbocharger (expansion ratio of 2.9) has been investigated and the results indicated superior performance of the rotor with a constant inlet blade angle relative to that with a nominally constant incidence angle. These results have been confirmed by the measurement of the three components of velocity, the Reynolds normal stresses and the flow angle at the inlet and exit of the mixed-flow turbine rotors by laser Doppler velocimetry (LDV) under steady state conditions. The turbine testing conditions corresponded to the 50% and 70% design speeds, equivalent to 29,400 and 41,300 rpm respectively. The velocity results have indicated that the flow upstream of the rotor varies significantly along the blade inlet plane, and this is more evident at the 50% design speed. The flow in the volute behaves as a free vortex except in regions close to the hub, while the exit flow revealed that the constant incidence design rotor has a significantly higher exit swirl angle than the constant blade design, in agreement with the higher exit kinetic energy loss in the former case.

Influence of different blade numbers on the performance of “saddle zone” in a mixed flow pump

2021 ◽  
pp. 095765092110460
Author(s):  
Leilei Ji ◽  
Wei Li ◽  
Weidong Shi ◽  
Fei Tian ◽  
Shuo Li ◽  
...  
Keyword(s):  
Flow Field ◽  
Leading Edge ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Mixed Flow ◽  
Impeller Blade ◽  
Flow Angle ◽  
Tip Leakage ◽  
Vorticity Transport ◽  
Flow Pump

In order to study the effect of different numbers of impeller blades on the performance of mixed-flow pump “saddle zone”, the external characteristic test and numerical simulation of mixed-flow pumps with three different impeller blade numbers were carried out. Based on high-precision numerical prediction, the internal flow field and tip leakage flow field of mixed flow pump under design conditions and stall conditions are investigated. By studying the vorticity transport in the stall flow field, the specific location of the high loss area inside the mixed flow pump impeller with different numbers of blades is located. The research results show that the increase in the number of impeller blades improve the pump head and efficiency under design conditions. Compared to the 4-blade impeller, the head and efficiency of the 5-blade impeller are increased by 5.4% and 21.9% respectively. However, the increase in the number of blades also leads to the widening of the “saddle area” of the mixed-flow pump, which leads to the early occurrence of stall and increases the instability of the mixed-flow pump. As the mixed-flow pump enters the stall condition, the inlet of the mixed-flow pump has a spiral swirl structure near the end wall for different blade numbers, but the depth and range of the swirling flow are different due to the change in the number of blades. At the same time, the change in the number of blades also makes the flow angle at 75% span change significantly, but the flow angle at 95% span is not much different because the tip leakage flow recirculates at the leading edge. Through the analysis of the vorticity transport results in the impeller with different numbers of blades, it is found that the reasons for the increase in the values of the vorticity transport in the stall condition are mainly impacted by the swirl flow at the impeller inlet, the tip leakage flow at the leading edge and the increased unsteady flow structures.

scholarly journals Reverse Thrust Aerodynamics of Variable Pitch Fans

2018 ◽  
Author(s):  
Tim S. Williams ◽  
Cesare A. Hall
Keyword(s):  
High Speed ◽  
Pressure Ratio ◽  
Test Case ◽  
Suction Surface ◽  
Flow Angle ◽  
Variable Pitch ◽  
Open Rotor ◽  
Weight Penalty ◽  
Reverse Thrust ◽  
Rotor Loss

Variable pitch fans are of interest for future low pressure ratio fan systems since they provide improved operability relative to fixed pitch fans. If they can also be re-pitched such that they generate sufficient reverse thrust they could eliminate the engine drag and weight penalty associated with bypass duct thrust reversers. This paper sets out to understand the details of the 3D fan stage flow field in reverse thrust operation. The study uses the Advanced Ducted Propulsor variable pitch fan test case, which has a design fan pressure ratio of 1.29. Comparison with spanwise probe measurements show that the computational approach is valid for examining the variation of loss and work in the rotor in forward thrust. The method is then extended to a reverse thrust configuration using an extended domain and appropriate boundary conditions. Computations, run at two rotor stagger settings, show that the spanwise variation in relative flow angle onto the rotor aligns poorly to the rotor inlet metal angle. This leads to two dominant rotor loss sources: one at the tip associated with positive incidence, and the second caused by negative incidence at lower span fractions. The second loss is reduced by opening the rotor stagger setting, and the first increases with rotor suction surface Mach number. The higher mass flow at more open rotor settings provide higher gross thrust, up to 49% of the forward take-off value, but is limited by the increased loss at high speed.

Aerodynamic Design and Optimization of Pipe Diffuser for a High-Loading Centrifugal Compressor

2017 ◽  
Author(s):  
Xi Yang ◽  
Dong-hai Jin ◽  
Xing-min Gui
Keyword(s):  
Flow Field ◽  
Design Method ◽  
Pressure Ratio ◽  
Leading Edge ◽  
Simulation Software ◽  
Field Analysis ◽  
Superior Performance ◽  
Critical Cross Section ◽  
Isentropic Efficiency ◽  
Vane Diffuser

Pipe diffuser draws more attentions these years as the stage pressure ratio and loads grow, since it is known that the pipe diffuser has a superior performance to the traditional vane diffuser as the diffuser inlet flow field is transonic or supersonic. Generally speaking, when the pressure ratio is high enough to give rise to the emergence of a critical cross-section, it would usually be in the diffuser, closing to the leading edge other than in the impeller. Therefore, the diffuser would have a significant impact on stage choke margin and its performance while be difficult to design and to match the impeller with satisfaction. To address the problem, a preliminary geometry design method for pipe diffuser is presented in this paper. In this paper, the performance and flow field analysis are based on numerical simulation carried out by Numeca, a commercial simulation software. For verified the calculated results′ reliability and grid independence, corresponding calculations and comparisons are conducted and discussed. Then, the performance of stage with pipe diffuser is compared with the stage with vane diffuser. Next, the specific effects of incidence on the performance and flow field are analyzed and discussed respectively. At last, an optimized aerodynamic structure of pipe diffuser is presented. As shown in the CFD results, the stage peak isentropic efficiency can reach up to 83.65% with the stage total pressure ratio slightly increased from 6.50 to 6.78, which means 4.29% of isentropic efficiency was raised by substituting the pipe diffuser for the vane diffuser.

scholarly journals Performance and Exit Flow Characteristics of Mixed-Flow Turbines

1997 ◽  
Vol 3 (4) ◽  
pp. 277-293 ◽  
Author(s):  
C. Arcoumanis ◽  
R. F. Martinez-Botas ◽  
J. M. Nouri ◽  
C. C. Su
Keyword(s):  
Steady State ◽  
Velocity Ratio ◽  
Tangential Velocity ◽  
Flow Characteristics ◽  
Mixed Flow ◽  
Cross Sectional ◽  
Flow Angle ◽  
Turbine Efficiency ◽  
And Performance ◽  
Inlet Angle

The performance and exit flow characteristics of two mixed-flow turbines have been investigated under steady-state conditions. The two rotors differ mainly in their inlet angle geometry, one has a nominal constant incidence (rotor B) and the other has a constant blade angle (rotor C), but also in the number of blades. The results showed that the overall peak efficiency of rotor C is higher than that of rotor B. Two different volutes were also used for the tests, differing in their cross-sectional area, which confirm that the new larger area volute turbine has a higher efficiency than the old one, particularly at lower speeds, and a fairly uniform variation with velocity ratio.The flow exiting the blades has been quantified by laser Doppler velocimetry. A difference in the exit flow velocity for rotors B and C with the new volute was observed which is expected given their variation in geometry and performance. The tangential velocities near the shroud resemble a forced vortex flow structure, while a uniform tangential velocity component was measured near the hub. The exit flow angles for both rotor cases decreased rapidly from the shroud to a minimum value in the annular core region before increasing gradually towards the hub. In addition, the exit flow angles with both rotors were reduced with increasing rotational speeds. The magnitude of the absolute flow angle was reduced in the case of rotor C, which may explain the improved steady state performance with this rotor. The results also revealed a correlation between the exit flow angle and the performance of the turbines; a reduction in flow angle resulted in an increase in the overall turbine efficiency.

Correlations Hidden in Compressor Maps

2011 ◽  
Author(s):  
Joachim Kurzke
Keyword(s):  
High Speed ◽  
Pressure Ratio ◽  
Leading Edge ◽  
Operating Conditions ◽  
Specific Work ◽  
Gas Generator ◽  
High Pressure Ratio ◽  
Map Adaptation ◽  
Physical Phenomena ◽  
Corrected Flow

Realistic compressor maps are the key to high quality gas turbine performance calculations. When modeling the performance of an existing engine then these maps are usually not known and must be approximated by adapting maps from literature to either measured data or to other available information. There are many publications describing map adaptation processes, simple ones and more sophisticated physically based scaling rules. There are also reports about using statistics, genetic algorithms, neural networks and even morphing techniques for re-engineering compressor maps. This type of methods does not consider the laws of physics and consequently the generated maps are valid at best in the region in which they have been calibrated. This region is frequently very narrow, especially in case of gas generator compressors which run in steady state always on a single operating line. This paper describes which physical phenomena influence the shape of speed and efficiency lines in compressor maps. For machines operating at comparatively low speeds (so that the flow into each stage is subsonic), there is usually considerable range between choke and stall corrected flow. As the speed of the machine is increased the range narrows. For high-speed stages with supersonic relative flow into the rotor the efficiency maximum is where the speed line turns over from vertical to lower than maximum corrected flow. At this operating condition the shock is about to detach from the leading edge of the blades. The flow at a certain speed can also be limited by choking in the compressor exit guide vanes. For high pressure ratio single stage centrifugal compressors this is a normal case, but it can also happen with low pressure ratio multistage boosters of turbofan engines, for example. If the compressor chokes at the exit, then the specific work remains constant along the speed line while the overall pressure ratio varies and that generates a very specific shape of the efficiency contour lines in the map. Also in other parts of the map, the efficiency varies along speed lines in a systematic manner. Peculiar shapes of specific work and corrected torque lines can reveal physically impossibilities that are difficult to see in the standard compressor map pictures. Compressor maps generated without considering the inherent physical phenomena can easily result in misleading performance calculations if used at operating conditions outside of the region where they have been calibrated. Whatever map adaptation method is used: the maps created in such a way should be checked thoroughly for violations of the underlying laws of compressor physics.

scholarly journals Flow Measurements Behind the Inlet Guide Vane of a Centrifugal Compressor

1998 ◽  
Author(s):  
I. Kassens ◽  
M. Rautenberg
Keyword(s):  
Centrifugal Compressor ◽  
Total Pressure ◽  
Guide Vane ◽  
Incidence Angle ◽  
Pressure Ratio ◽  
Inlet Guide Vane ◽  
Flow Measurements ◽  
Flow Angle ◽  
Partial Load ◽  
Measurement Location

In a centrifugal compressor adjustable inlet guide vanes (IGV) in front of the impeller are used to regulate the pressure ratio and the mass flow. The stationary measurement of the velocity profile in front of the impeller with different angles of the IGV displays shock losses at the inlet edge of blade of the impeller. In the partial-load region (e.g. partial-load efficiency) the radial distribution of the flow influences considerably the performance of the impeller. The tested compressor consists of an adjustable IGV with straight vanes, a shrouded impeller and a vaneless, parallel diffuser. In the first measurement location, behind the IGV, total pressure, static pressure and flow angle were measured with a 5-hole cylinder probe. In the second measurement location, in front of the impeller, the measurement of the total pressure was carried out with a Kiel probe and the flow angle with a Cobra probe accordingly the static wall pressure was measured. Taking into consideration the fundamental thermodynamical equations it was possible to determine the velocity profiles because of the measured distributions of the flow angle in these two measurement locations. For different angles of the IGV and with various mass flows the distributions of the deflection defect behind the IGV are described. Starting with the measured distributions of the flow in front of the impeller the flow angles at the impeller inlet are calculated and the distributions of the incidence angle at the impeller inlet are figured out.

scholarly journals Interpreting Aerodynamics of a Transonic Impeller from Static Pressure Measurements

2018 ◽  
Vol 2018 ◽  
pp. 1-9
Author(s):  
Fangyuan Lou ◽  
John Charles Fabian ◽  
Nicole Leanne Key
Keyword(s):  
Flow Field ◽  
High Speed ◽  
Static Pressure ◽  
Pressure Ratio ◽  
Leading Edge ◽  
Pressure Measurements ◽  
High Loss ◽  
Supersonic Inlet ◽  
Mach Numbers ◽  
Inlet Conditions

This paper investigates the aerodynamics of a transonic impeller using static pressure measurements. The impeller is a high-speed, high-pressure-ratio wheel used in small gas turbine engines. The experiment was conducted on the single stage centrifugal compressor facility in the compressor research laboratory at Purdue University. Data were acquired from choke to near-surge at four different corrected speeds (Nc) from 80% to 100% design speed, which covers both subsonic and supersonic inlet conditions. Details of the impeller flow field are discussed using data acquired from both steady and time-resolved static pressure measurements along the impeller shroud. The flow field is compared at different loading conditions, from subsonic to supersonic inlet conditions. The impeller performance was strongly dependent on the inducer, where the majority of relative diffusion occurs. The inducer diffuses flow more efficiently for inlet tip relative Mach numbers close to unity, and the performance diminishes at other Mach numbers. Shock waves emerging upstream of the impeller leading edge were observed from 90% to 100% corrected speed, and they move towards the impeller trailing edge as the inlet tip relative Mach number increases. There is no shock wave present in the inducer at 80% corrected speed. However, a high-loss region near the inducer throat was observed at 80% corrected speed resulting in a lower impeller efficiency at subsonic inlet conditions.

Sign in / Sign up

Export Citation Format

Share Document