Acoustic Emission During Athermal Martensitic Transformation in Steels

1990 ◽  
Vol 112 (1) ◽  
pp. 84-91 ◽  
Author(s):  
Xiangying Liu ◽  
Elijah Kannatey-Asibu
Keyword(s):  
Free Energy ◽  
Acoustic Emission ◽  
Martensitic Transformation ◽  
Signal Intensity ◽  
Temperature Derivative ◽  
Process Characteristics ◽  
Ae Signal ◽  
The Relationship ◽  
Ae Signals ◽  
Start Temperature

A relationship developed earlier between acoustic emission signals and the process of athermal martensitic transformation based on the free energy associated with the process is extended and verified experimentally. The relationship is found to model the process characteristics very well. The intensity of AE signal generated during transformation was found to be proportional to the temperature derivative of the fraction of martensite, the cooling rate, and volume of specimen. The AE signal was also found to be related to the carbon content of the steel. During transformation, the signal intensity was found to increase to a peak, and then tail off near the end of the transformation. Values of the martensite start temperature obtained from plots of the total RMS squared AE signals were also found to correlate well with values from the literature.

scholarly journals Study on the Acoustic Emission Characteristics of Different Rock Types and Its Fracture Mechanism in Brazilian Splitting Test

2021 ◽  
Vol 9 ◽  
Author(s):  
Li Shengxiang ◽  
Xie Qin ◽  
Liu Xiling ◽  
Li Xibing ◽  
Luo Yu ◽  
...  
Keyword(s):  
Acoustic Emission ◽  
Rock Fracture ◽  
Peak Frequency ◽  
Test System ◽  
Mineral Particle ◽  
Splitting Test ◽  
Ae Signal ◽  
The Relationship ◽  
Ae Signals ◽  
Internal Fracture

In order to investigate the relationship between rock microfracture mechanism and acoustic emission (AE) signal characteristic parameters under split loads, the MTS322 servo-controlled rock mechanical test system was employed to carry out the Brazilian split tests on granite, marble, sandstone, and limestone, while FEI Quanta-200 scanning electron microscope system was employed to carry out the analysis of fracture morphology. The results indicate that different scales of mineral particle, mineral composition, and discontinuity have influence on the fracture characteristics of rock, as well as the b-value. The peak frequency distribution of the AE signal has obvious zonal features, and these distinct peak frequencies of four types of rock fall mostly in ranges of 0–100 kHz, 100–300 kHz, and above 300 kHz. Due to the different rock properties and mineral compositions, the proportions of peak frequencies in these intervals are also different among the four rocks, which are also acting on the b-value. In addition, for granite, the peak frequencies of AE signals are mostly distributed above 300 kHz for granite, marble, and limestone, which mainly derive from the internal fracture of k-feldspar minerals; for marble, the AE signals with peak frequency are mostly distributed in over 300 kHz, which mainly derive from the internal fracture of dolomite minerals and calcite minerals; AE signals for sandstone are mostly distributed in the range of 0–100 kHz, which mainly derive from the internal fracture of quartz minerals; for limestone, the AE signals with peak frequency are mostly distributed in over 300 kHz, which mainly derive from the internal fracture of granular-calcite minerals. The relationship between acoustic emission signal frequency of rock fracture and the fracture scale is constructed through experiments, which is of great help for in-depth understanding of the scaling relationship of rock fracture.

scholarly journals Analysis of Acoustic Emission (AE) Signals for Quality Monitoring of Laser Lap Microwelding

2021 ◽  
Vol 11 (15) ◽  
pp. 7045
Author(s):  
Ming-Chyuan Lu ◽  
Shean-Juinn Chiou ◽  
Bo-Si Kuo ◽  
Ming-Zong Chen
Keyword(s):  
Stainless Steel ◽  
Acoustic Emission ◽  
Frequency Domain ◽  
Monitoring System ◽  
Welding Quality ◽  
Steel Sheets ◽  
Signal Features ◽  
Ae Signal ◽  
Laser Microwelding ◽  
Ae Signals

In this study, the correlation between welding quality and features of acoustic emission (AE) signals collected during laser microwelding of stainless-steel sheets was analyzed. The performance of selected AE features for detecting low joint bonding strength was tested using a developed monitoring system. To obtain the AE signal for analysis and develop the monitoring system, lap welding experiments were conducted on a laser microwelding platform with an attached AE sensor. A gap between the two layers of stainless-steel sheets was simulated using clamp force, a pressing bar, and a thin piece of paper. After the collection of raw signals from the AE sensor, the correlations of welding quality with the time and frequency domain features of the AE signals were analyzed by segmenting the signals into ten 1 ms intervals. After selection of appropriate AE signal features based on a scatter index, a hidden Markov model (HMM) classifier was employed to evaluate the performance of the selected features. Three AE signal features, namely the root mean square (RMS) of the AE signal, gradient of the first 1 ms of AE signals, and 300 kHz frequency feature, were closely related to the quality variation caused by the gap between the two layers of stainless-steel sheets. Classification accuracy of 100% was obtained using the HMM classifier with the gradient of the signal from the first 1 ms interval and with the combination of the 300 kHz frequency domain signal and the RMS of the signal from the first 1 ms interval.

Experiment on Surface Roughness and Acoustic Emission Signal in Infeed Period of Cylindrical Plunge Grinding

2013 ◽  
Vol 690-693 ◽  
pp. 2442-2445 ◽  
Author(s):  
Hao Lin Li ◽  
Hao Yang Cao ◽  
Chen Jiang
Keyword(s):  
Surface Roughness ◽  
Acoustic Emission ◽  
Acoustic Emission Signal ◽  
Feed Rate ◽  
Grinding Process ◽  
Experiment Research ◽  
Plunge Grinding ◽  
Emission Signal ◽  
Ae Signal ◽  
Ae Signals

This work presents an experiment research on Acoustic emission (AE) signal and the surface roughness of cylindrical plunge grinding with the different infeed time. The changed infeed time of grinding process is researched as an important parameter to compare AE signals and surface roughnesses with the different infeed time in the grinding process. The experiment results show the AE signal is increased by the increased feed rate. In the infeed period of the grinding process, the surface roughness is increased at first, and then is decreased.

Research on Feature Extraction Method Based on Rub-Impact Acoustic Emission Signals of Mechanical Seal End Faces

2010 ◽  
Vol 36 ◽  
pp. 68-74
Author(s):  
Chuan Jun Liao ◽  
Shuang Fu Suo ◽  
Wei Feng Huang
Keyword(s):  
Acoustic Emission ◽  
Feature Extraction ◽  
Extraction Methods ◽  
Mechanical Seal ◽  
Mechanical Seals ◽  
Feature Extraction Method ◽  
Different Types ◽  
Ae Signal ◽  
Feature Information ◽  
Ae Signals

Acoustic emission (AE) techniques are put forward to monitor rub-impacts between rotating rings and stationary rings of mechanical seals by this paper. By analyzing feature extraction methods of the typical rub-impact AE signal, the method combining of wavelet scalogram and power spectrum is found useful, and can used to attribute the feature information implicated in rub-impact AE signals of mechanical seal end faces. Both simulations and experimental research prove that the method is effective, and are used successfully to identify the typical features of different types of rub-impacts of mechanical seal end faces.

scholarly journals Internal Leakage Predicition of Hydraulic Spool valves Based on Acoustic Emission Technology

2021 ◽  
Vol 2113 (1) ◽  
pp. 012016
Author(s):  
Fei Song ◽  
Likun Peng ◽  
Jia Chen ◽  
Benmeng Wang
Keyword(s):  
Acoustic Emission ◽  
High Frequency ◽  
Peak Frequency ◽  
Leakage Rate ◽  
High Frequency Band ◽  
Signal Characteristics ◽  
Spool Valves ◽  
The Relationship ◽  
Ae Signals ◽  
Acoustic Emission Technology

Abstract In order to realize the nondestructive testing (NDT) of the internal leakage fault of hydraulic spool valves, the internal leakage rate must be predicted by AE (acoustic emission) technology. An AE experimental platform of internal leakage of hydraulic spool valves is built to study the characteristics of AE signals of internal leakage and the relationship between AE signals and leakage rates. The research results show the AE signals present a wideband characteristic. The main frequencies are concentrated in 30~50 kHz and the peak frequency is around 40 kHz. When the leakage rate is large, there are significant signal characteristics appearing in the high frequency band of 75~100 kHz. The exponent of the root mean square(RMS) of AE signals is positively correlated with the exponent of the leakage rate only if the leakage rate is greater than 2~3 mL/min. This find could be used to predict the internal leakage rate of hydraulic spool valves.

Reciprocating compressor valve damage estimation under varying speeds through the acoustic emission technique

2019 ◽  
Vol 10 (5) ◽  
pp. 621-633
Author(s):  
Hoi-Yin Sim ◽  
Rahizar Ramli ◽  
Ahmad Saifizul
Keyword(s):  
Acoustic Emission ◽  
Regression Analysis ◽  
Flow Rate ◽  
Reciprocating Compressor ◽  
Damage Estimation ◽  
Content Type ◽  
Air Compressor ◽  
Ae Signal ◽  
Valve Opening ◽  
Ae Signals

Purpose The purpose of this paper is to examine the effect of reciprocating compressor speeds and valve conditions on the roor-mean-square (RMS) value of burst acoustic emission (AE) signals associated with the physical motion of valves. The study attempts to explore the potential of AE signal in the estimation of valve damage under varying compressor speeds. Design/methodology/approach This study involves the acquisition of AE signal, valve flow rate, pressure and temperature at the suction valve of an air compressor with speed varrying from 450 to 800 rpm. The AE signals correspond to one compressor cycle obtained from two simulated valve damage conditions, namely, the single leak and double leak conditions are compared to those of the normal valve plate. To examine the effects of valve conditions and speeds on AE RMS values, two-way analysis of variance (ANOVA) is conducted. Finally, regression analysis is performed to investigate the relationship of AE RMS with the speed and valve flow rate for different valve conditions. Findings The results showed that AE RMS values computed from suction valve opening (SVO), suction valve closing (SVC) and discharge valve opening (DVO) events are significantly affected by both valve conditions and speeds. The AE RMS value computed from SVO event showed high linear correlation with speed compared to SVC and DVO events for all valve damage conditions. As this study is conducted at a compressor running at freeload, increasing speed of compressor also results in the increment of flow rate. Thus, the valve flow rate can also be empirically derived from the AE RMS value through the regression method, enabling a better estimation of valve damages. Research limitations/implications The experimental test rig of this study is confined to a small pressure ratio range of 1.38–2.03 (free-loading condition). Besides, the air compressor is assumed to be operated at a constant speed. Originality/value This study employed the statistical methods namely the ANOVA and regression analysis for valve damage estimation at varying compressor speeds. It can enable a plant personnel to make a better prediction on the loss of compressor efficiency and help them to justify the time for valve replacement in future.

scholarly journals Friction and Wear Monitoring Methods for Journal Bearings of Geared Turbofans Based on Acoustic Emission Signals and Machine Learning

Lubricants ◽  
2020 ◽  
Vol 8 (3) ◽  
pp. 29 ◽  
Author(s):  
Noushin Mokhtari ◽  
Jonathan Gerald Pelham ◽  
Sebastian Nowoisky ◽  
José-Luis Bote-Garcia ◽  
Clemens Gühmann
Keyword(s):  
Machine Learning ◽  
Acoustic Emission ◽  
Friction And Wear ◽  
Journal Bearing ◽  
Journal Bearings ◽  
Wear Volume ◽  
Time Frequency ◽  
Ae Signal ◽  
Ae Signals

In this work, effective methods for monitoring friction and wear of journal bearings integrated in future UltraFan® jet engines containing a gearbox are presented. These methods are based on machine learning algorithms applied to Acoustic Emission (AE) signals. The three friction states: dry (boundary), mixed, and fluid friction of journal bearings are classified by pre-processing the AE signals with windowing and high-pass filtering, extracting separation effective features from time, frequency, and time-frequency domain using continuous wavelet transform (CWT) and a Support Vector Machine (SVM) as the classifier. Furthermore, it is shown that journal bearing friction classification is not only possible under variable rotational speed and load, but also under different oil viscosities generated by varying oil inlet temperatures. A method used to identify the location of occurring mixed friction events over the journal bearing circumference is shown in this paper. The time-based AE signal is fused with the phase shift information of an incremental encoder to achieve an AE signal based on the angle domain. The possibility of monitoring the run-in wear of journal bearings is investigated by using the extracted separation effective AE features. Validation was done by tactile roughness measurements of the surface. There is an obvious AE feature change visible with increasing run-in wear. Furthermore, these investigations show also the opportunity to determine the friction intensity. Long-term wear investigations were done by carrying out long-term wear tests under constant rotational speeds, loads, and oil inlet temperatures. Roughness and roundness measurements were done in order to calculate the wear volume for validation. The integrated AE Root Mean Square (RMS) shows a good correlation with the journal bearing wear volume.

Quantitative Relationship between Strain and Acoustic Emission Response in Monitoring Fatigue Damage

2013 ◽  
Vol 66 (1) ◽  
Author(s):  
M. Mohammad ◽  
S. Abdullah ◽  
N. Jamaludin ◽  
O. Innayatullah
Keyword(s):  
Acoustic Emission ◽  
Failure Mechanism ◽  
Fatigue Failure ◽  
Quantitative Relationship ◽  
Steel Specimen ◽  
Cyclic Fatigue ◽  
Steel Component ◽  
Specific Data ◽  
The Relationship ◽  
Ae Signals

This study was carried out to investigate the relationship between the strain and acoustic emission (AE) signals, thus, to confirm the capability of AE technique to monitor the fatigue failure mechanism of a steel component. To achieve this goal, strain and AE signals were captured on the steel specimen during the cyclic fatigue test.  Both signals were collected using specific data acquisition system by attaching the strain gauge and AE piezoelectric transducer simultaneously at the specimen during the test. The stress loading used for the test was set at 600 MPa, and the specimens were fabricated using the SAE 1045 carbon steel.  The related parameters for both signals were determined at every 2000 seconds until the specimen failed.  It was found that a meaningful correlation of all parameters, i.e. amplitude, kurtosis and energy, was established. Finally, all AE parameters are correlated with the damage values, which have been estimated using the Coffin-Manson model.  Hence, it was suggested that the AE technique can be used as a monitoring tool for fatigue failure mechanism in a steel component.

scholarly journals Damage evolution in wood – pattern recognition based on acoustic emission (AE) frequency spectra

Holzforschung ◽  
2015 ◽  
Vol 69 (3) ◽  
pp. 357-365 ◽  
Author(s):  
Franziska Baensch ◽  
Markus G.R. Sause ◽  
Andreas J. Brunner ◽  
Peter Niemz
Keyword(s):  
Pattern Recognition ◽  
Acoustic Emission ◽  
Cluster Formation ◽  
Low Frequency ◽  
Tensile Tests ◽  
Most Probable Number ◽  
Frequency Spectra ◽  
Probable Number ◽  
Ae Signal ◽  
Ae Signals

Abstract Tensile tests on miniature spruce specimens have been performed by means of acoustic emission (AE) analysis. Stress was applied perpendicular (radial direction) and parallel to the grain. Nine features were selected from the AE frequency spectra. The signals were classified by means of an unsupervised pattern recognition approach, and natural classes of AE signals were identified based on the selected features. The algorithm calculates the numerically best partition based on subset combinations of the features provided for the analysis and leads to the most significant partition including the respective feature combination and the most probable number of clusters. For both specimen types investigated, the pattern recognition technique indicates two AE signal clusters. Cluster A comprises AE signals with a relatively high share of low-frequency components, and the opposite is true for cluster B. It is hypothesized that the signature of rapid and slow crack growths might be the origin for this cluster formation.

INFLUENCE OF ACOUSTIC-ELECTRONIC CHANNEL ON ACOUSTIC EMISSION HIT PARAMETERS

2020 ◽  
pp. 14-22
Author(s):  
A. A. Sazonov ◽  
V. I. Shelobkov ◽  
V. I. Ivanov
Keyword(s):  
Acoustic Emission ◽  
Significant Influence ◽  
Signal Propagation ◽  
Propagation Channel ◽  
Object State ◽  
Signal Parameters ◽  
Ae Signal ◽  
Electronic Channel ◽  
Ae Signals ◽  
Electronic Channels

The paper deals with the influence of acoustic emission (AE) signal propagation channel on the parameters of these signals, which are used to judge the object state. It is shown that the acoustic channel, which includes the testing object and the acoustic emission transducer, has a significant influence on the parameters of AE signals. This must be taken into account, both in the interpretation of signals and in the calibration of acoustic emission transducers. Specific examples of degradation of AE signal parameters during the passage of acoustic-electronic channels are shown.

Sign in / Sign up

Export Citation Format

Share Document