Numerical Investigation of the Solidity Effect on Linear Compressor Cascades

2014 ◽  
Author(s):  
J. Sans ◽  
M. Resmini ◽  
J.-F. Brouckaert ◽  
S. Hiernaux
Keyword(s):  
Numerical Investigation ◽  
State Of The Art ◽  
Leading Edge ◽  
Operating Conditions ◽  
Compressor Cascade ◽  
Minimum Loss ◽  
Low Speed ◽  
High Mach ◽  
The Stability ◽  
The Impact

Solidity in compressors is defined as the ratio of the aerodynamic chord over the peripheral distance between two adjacent blades, the pitch. This parameter is simply the inverse of the pitch-to-chord ratio generally used in turbines. Solidity must be selected at the earliest design phase, i.e. at the level of the meridional design and represents a crucial step in the whole design process. Most of the existing studies on this topic rely on low-speed compressor cascade correlations from Carter or Lieblein. The aim of this work is to update those correlations for state-of-the-art controlled diffusion blades, and extend their application to high Mach number flow regimes more typical of modern compressors. Another objective is also to improve the physical understanding of the solidity effect on compressor performance and stability. A numerical investigation has been performed using the commercial software FINE/Turbo. Two different blade profiles were selected and investigated in the compressible flow regime as an extension to the low-speed data on which the correlations are based. The first cascade uses a standard double circular arc profile, extensively referenced in the literature, while the second configuration uses a state-of-the-art CDB, representative of low pressure compressor stator mid-span profile. Both profiles have been designed with the same inlet and outlet metal angles and the same maximum thickness but the camber and thickness distributions, the stagger angle and the leading edge geometry of the CDB have been optimized. The determination of minimum loss, optimum incidence and deviation is addressed and compared with existing correlations for both configurations and various Mach numbers that have been selected in order to match typical booster stall and choke operating conditions. The emphasis is set on the minimum loss performance at mid-span. The impact of the solidity on the operating range and the stability of the cascade are also studied.

Numerical Investigation of Passive Flow Control Using Wavy Blades in a Highly-Loaded Compressor Cascade

2018 ◽  
Author(s):  
Bo Wang ◽  
Yanhui Wu ◽  
Kai Liu
Keyword(s):  
Numerical Investigation ◽  
Flow Structure ◽  
Cross Flow ◽  
Leading Edge ◽  
Control Flow ◽  
Streamwise Vortices ◽  
Compressor Cascade ◽  
Control Effect ◽  
Suction Surface ◽  
Highly Loaded

Driven by the need to control flow separations in highly loaded compressors, a numerical investigation is carried out to study the control effect of wavy blades in a linear compressor cascade. Two types of wavy blades are studied with wavy blade-A having a sinusoidal leading edge, while wavy blade-B having pitchwise sinusoidal variation in the stacking line. The influence of wavy blades on the cascade performance is evaluated at incidences from −1° to +9°. For the wavy blade-A with suitable waviness parameters, the cascade diffusion capacity is enhanced accompanied by the loss reduction under high incidence conditions where 2D separation is the dominant flow structure on the suction surface of the unmodified blade. For well-designed wavy blade-B, the improvement of cascade performance is achieved under low incidence conditions where 3D corner separation is the dominant flow structure on the suction surface of the baseline blade. The influence of waviness parameters on the control effect is also discussed by comparing the performance of cascades with different wavy blade configurations. Detailed analysis of the predicted flow field shows that both the wavy blade-A and wavy blade-B have capacity to control flow separation in the cascade but their control mechanism are different. For wavy blade-A, the wavy leading edge results in the formation of counter-rotating streamwise vortices downstream of trough. These streamwise vortices can not only enhance momentum exchange between the outer flow and blade boundary layer, but also act as the suction surface fence to hamper the upwash of low momentum fluid driven by cross flow. For wavy blade-B, the wavy surface on the blade leads to a reduction of the cross flow upwash by influencing the spanwise distribution of the suction surface static pressure and guiding the upwash flow.

Modeling of External Pressure Gradient Influence on the Stability of Disturbances in the Boundary Layers of Compressed Gas

2013 ◽  
Vol 8 (4) ◽  
pp. 64-75
Author(s):  
Sergey Gaponov ◽  
Natalya Terekhova
Keyword(s):  
Mach Number ◽  
Pressure Gradient ◽  
Boundary Layers ◽  
Leading Edge ◽  
External Pressure ◽  
Transition To Turbulence ◽  
Compressed Gas ◽  
High Mach ◽  
The Stability ◽  
Very High

This work continues the research on modeling of passive methods of management of flow regimes in the boundary layers of compressed gas. Authors consider the influence of pressure gradient on the evolution of perturbations of different nature. For low Mach number M = 2 increase in pressure contributes to an earlier transition of laminar to turbulent flow, and, on the contrary, drop in the pressure leads to a prolongation of the transition to turbulence. For high Mach number M = 5.35 found that the acoustic disturbances exhibit a very high dependence on the sign and magnitude of the external gradient, with a favorable gradient of the critical Reynolds number becomes smaller than the vortex disturbances, and at worst – boundary layer is destabilized directly on the leading edge

An Impact of Various Shroud Bleed Slot Configurations and Cavity Vanes on Compressor Map Width and the Inducer Flow Field

2013 ◽  
Vol 135 (4) ◽  
Author(s):  
Subenuka Sivagnanasundaram ◽  
Stephen Spence ◽  
Juliana Early ◽  
Bahram Nikpour
Keyword(s):  
Flow Field ◽  
Incidence Angle ◽  
Pressure Ratio ◽  
Leading Edge ◽  
Operating Conditions ◽  
Choked Flow ◽  
Recirculating Flow ◽  
Heavy Duty Diesel ◽  
Compressor Map ◽  
The Impact

This paper describes an investigation of map width enhancement and a detailed analysis of the inducer flow field due to various bleed slot configurations and vanes in the annular cavity of a turbocharger centrifugal compressor. The compressor under investigation is used in a turbocharger application for a heavy duty diesel engine of approximately 400 hp. This investigation has been undertaken using a computational fluid dynamics (CFD) model of the full compressor stage, which includes a manual multiblock-structured grid generation method. The influence of the bleed slot flow on the inducer flow field at a range of operating conditions has been analyzed, highlighting the improvement in surge and choked flow capability. The impact of the bleed slot geometry variations and the inclusion of cavity vanes on the inlet incidence angle have been studied in detail by considering the swirl component introduced at the leading edge by the recirculating flow through the slot. Further, the overall stage efficiency and the nonuniform flow field at the inducer inlet have been also analyzed. The analysis revealed that increasing the slot width has increased the map width by about 17%. However, it has a small impact on the efficiency, due to the frictional and mixing losses. Moreover, adding vanes in the cavity improved the pressure ratio and compressor performance noticeably. A detail analysis of the compressor with cavity vanes has also been presented.

1997 Best Paper Award—Turbomachinery Committee: A Study of Spike and Modal Stall Phenomena in a Low-Speed Axial Compressor

1998 ◽  
Vol 120 (3) ◽  
pp. 393-401 ◽  
Author(s):  
T. R. Camp ◽  
I. J. Day
Keyword(s):  
High Speed ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Short Length ◽  
Operating Conditions ◽  
Length Scale ◽  
Stall Inception ◽  
Low Speed ◽  
The Stability ◽  
Dimensional Instability

This paper presents a study of stall inception mechanisms in a low-speed axial compressor. Previous work has identified two common flow breakdown sequences, the first associated with a short length-scale disturbance known as a “spike,” and the second with a longer length-scale disturbance known as a “modal oscillation.” In this paper the physical differences between these two mechanisms are illustrated with detailed measurements. Experimental results are also presented that relate the occurrence of the two stalling mechanisms to the operating conditions of the compressor. It is shown that the stability criteria for the two disturbances are different: Long length-scale disturbances are related to a two-dimensional instability of the whole compression system, while short length-scale disturbances indicate a three-dimensional breakdown of the flow-field associated with high rotor incidence angles. Based on the experimental measurements, a simple model is proposed that explains the type of stall inception pattern observed in a particular compressor. Measurements from a single-stage low-speed compressor and from a multistage high-speed compressor are presented in support of the model.

A Study of Spike and Modal Stall Phenomena in a Low-Speed Axial Compressor

1997 ◽  
Author(s):  
T. R. Camp ◽  
I. J. Day
Keyword(s):  
High Speed ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Operating Conditions ◽  
Two Dimensional ◽  
Stability Criteria ◽  
Stall Inception ◽  
Low Speed ◽  
The Stability ◽  
Dimensional Instability

This paper presents a study of stall inception mechanisms a in low-speed axial compressor. Previous work has identified two common flow breakdown sequences, the first associated with a short lengthscale disturbance known as a ‘spike’, and the second with a longer lengthscale disturbance known as a ‘modal oscillation’. In this paper the physical differences between these two mechanisms are illustrated with detailed measurements. Experimental results are also presented which relate the occurrence of the two stalling mechanisms to the operating conditions of the compressor. It is shown that the stability criteria for the two disturbances are different: long lengthscale disturbances are related to a two-dimensional instability of the whole compression system, while short lengthscale disturbances indicate a three-dimensional breakdown of the flow-field associated with high rotor incidence angles. Based on the experimental measurements, a simple model is proposed which explains the type of stall inception pattern observed in a particular compressor. Measurements from a single stage low-speed compressor and from a multistage high-speed compressor are presented in support of the model.

Endwall Boundary Layer Control in Compressor Cascades

2004 ◽  
Author(s):  
Ralf Mu¨ller ◽  
Konrad Vogeler ◽  
Helmut Sauer ◽  
Martin Hoeger
Keyword(s):  
Boundary Layer ◽  
Leading Edge ◽  
Suction Side ◽  
Boundary Layer Control ◽  
Compressor Cascade ◽  
Low Speed ◽  
Passage Vortex ◽  
Additional Losses ◽  
Layer Control ◽  
Horse Shoe Vortex

Recent investigations have shown a reduction of secondary losses in compressor cascades using a bulb like modification of the profile at the endwall. This paper is focussed on experimental work in comparison of 5 different endwall modifications at a compressor cascade. The cascade is modified near the endwall with a bulb, a medium and a large fillet. The fillet configurations are modified by an axial blunt cut-off at the leading edge. The investigations have been carried out at a profile developed from a hub section of the Dresden Low Speed Research Compressor (LSRC) blade, a compressor profile with a nominal turning of 18 deg. A datum configuration and the 5 other configurations were tested at the Low Speed Cascade Windtunnel (LSCW). For the bulb configuration, an intensified horse shoe vortex was suspected and observed counterrotating to the passage vortex with an influence on its propagation. The interaction of the passage vortex and the suction side profile boundary layer is influenced. The superposition of both is minimized and the losses developing from this effect are significant lower. For the fillet and blunt-fillet configurations, a fillet vortex develops and was observed co-rotating to the passage vortex with an influence on the mentioned interaction as well. Blunt leading edges produce additional losses but the superposition of the growing vortices may reduce the overall losses. The cases show a reduction in losses of 1.9% for 3 deg incidence and a range of 1.2% rise to 1.9% reduction in dependence of the incidence. This equals a reduction of the isolated secondary losses up to 28% with respect to the reference profile. Detailed results of the experiments are presented for the reference and all modified cascades.

scholarly journals Industrial Gas Turbine Performance: Compressor Fouling and On-Line Washing

2014 ◽  
Vol 136 (10) ◽  
Author(s):  
Uyioghosa Igie ◽  
Pericles Pilidis ◽  
Dimitrios Fouflias ◽  
Kenneth Ramsden ◽  
Panagiotis Laskaridis
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Engine Performance ◽  
Operating Conditions ◽  
Compressor Cascade ◽  
Compressor Blades ◽  
Turbine Performance ◽  
Industrial Gas Turbines ◽  
On Line ◽  
The Impact

Industrial gas turbines are susceptible to compressor fouling, which is the deposition and accretion of airborne particles or contaminants on the compressor blades. This paper demonstrates the blade aerodynamic effects of fouling through experimental compressor cascade tests and the accompanied engine performance degradation using turbomatch, an in-house gas turbine performance software. Similarly, on-line compressor washing is implemented taking into account typical operating conditions comparable with industry high pressure washing. The fouling study shows the changes in the individual stage maps of the compressor in this condition, the impact of degradation during part-load, influence of control variables, and the identification of key parameters to ascertain fouling levels. Applying demineralized water for 10 min, with a liquid-to-air ratio of 0.2%, the aerodynamic performance of the blade is shown to improve, however most of the cleaning effect occurred in the first 5 min. The most effectively washed part of the blade was the pressure side, in which most of the particles deposited during the accelerated fouling. The simulation of fouled and washed engine conditions indicates 30% recovery of the lost power due to washing.

An Impact of Various Shroud Bleed Slot Configurations and Cavity Vanes on Compressor Map Width and the Inducer Flow Field

2011 ◽  
Author(s):  
Subenuka Sivagnanasundaram ◽  
Stephen Spence ◽  
Juliana Early ◽  
Bahram Nikpour
Keyword(s):  
Flow Field ◽  
Incidence Angle ◽  
Pressure Ratio ◽  
Leading Edge ◽  
Operating Conditions ◽  
Choked Flow ◽  
Recirculating Flow ◽  
Heavy Duty Diesel ◽  
Compressor Map ◽  
The Impact

This paper describes an investigation of map width enhancement and a detailed analysis of the inducer flow field due to various bleed slot configurations and vanes in the annular cavity of a turbocharger centrifugal compressor. The compressor under investigation is used in a turbocharger application for a heavy duty diesel engine of approximately 400hp. This investigation has been undertaken using a CFD model of the full compressor stage which includes a manual multi-block structured grid generation method. The influence of the bleed slot flow on the inducer flow field at a range of operating conditions has been analysed, highlighting the improvement in surge and choked flow capability. The impact of the bleed slot geometry variations and the inclusion of cavity vanes on the inlet incidence angle have been studied in detail by considering the swirl component introduced at the leading edge by the recirculating flow through the slot. Further, the overall stage efficiency and the non-uniform flow field at the inducer inlet have been also analysed. The analysis revealed that increasing the slot width has increased the map width by about 17%. However, it has a small impact on the efficiency due to the frictional and mixing losses. Moreover, adding vanes in the cavity improved the pressure ratio and compressor performance noticeably. A detail analysis of the compressor with cavity vanes has also been presented.

Study of the Dynamic Characteristics of Piston Chamber Pressure and its Optimizing

2014 ◽  
Vol 602-605 ◽  
pp. 277-282
Author(s):  
Bin Qu Yan ◽  
Shu Mei Chen ◽  
Chuan Ming Chen
Keyword(s):  
Dynamic Response ◽  
Operating Conditions ◽  
Piston Pump ◽  
Cylinder Block ◽  
Chamber Pressure ◽  
Excessive Pressure ◽  
New Type ◽  
The Stability ◽  
The Impact ◽  
Piston Chamber

In order to develop a new type of high-performance axial piston pump, the impact of the dynamic response characteristics of piston chamber pressure to the stability of cylinder block were analyzed. This paper a new type of valve plate which combined two fixed throttling grooves with a triangular groove (called three-level gain) was put forward so as to reducing the excessive pressure adjustment of the dynamic response of piston chamber pressure and improving the stability of cylinder block. The simulation results indicate that not only the cavitation is reduced, but also the stability of the dynamic response of piston chamber pressure is remained at various swash plate angle which makes it applicable to variable piston pump. The results also indicate that the flow pulsation of variable displacement pump is significantly decreased in different operating conditions.

Sign in / Sign up

Export Citation Format

Share Document