Further Investigation on Transonic Compressor Stall Margin Enhancement With Stall Precursor-Suppressed Casing Treatment

2015 ◽  
Vol 138 (2) ◽  
Author(s):  
Dakun Sun ◽  
Chaoqun Nie ◽  
Xiaohua Liu ◽  
Feng Lin ◽  
Xiaofeng Sun
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Rotational Speed ◽  
Solid Wall ◽  
Stall Inception ◽  
Stall Margin ◽  
Casing Treatment ◽  
Transonic Compressor ◽  
Stall Precursor

A kind of casing treatment, named as stall precursor-suppressed (SPS), has been developed recently, which was proved to be able to effectively improve stall margin (SM) without significant efficiency loss in low-speed axial flow compressors and a transonic compressor rotor. In this paper, the effectiveness of the SPS casing treatment is investigated in a single-stage transonic compressor. Based on an extended stall inception model, the quantitative evaluation of the SM enhancement by the SPS casing treatment is presented for the transonic compressor stage. The model predicts that a 2.5–6.8% of stall margin improvement (SMI), which is defined in terms of mass flow rate at stall inception, can be achieved at the design rotational speed. The experimental results show that the SPS casing treatment can achieve 3.5–9.3% of the SMI at 95% design rotational speed. Due to the fact that the distributions of the total pressure ratio along the spanwise direction are kept the same as those of the solid wall casing at the same mass flow rate, the SPS casing treatments with a small open area ratio and large backchamber enhance the SM without a recognizable efficiency loss and a migration of the pressure-rise characteristics. Furthermore, the mechanism of SMI with the SPS casing treatment is investigated in the experiments. In comparison with the solid wall casing, the emergence and the evolution of the stall inception waves are suppressed and the nonlinear development of the stall process is delayed with the SPS casing treatment.

Analysis on slot-type casing treatment injection flow in an axial transonic compressor

2016 ◽  
Vol 230 (8) ◽  
pp. 792-804 ◽  
Author(s):  
Mingmin Zhu ◽  
Xiaoqing Qiang ◽  
Wensheng Yu ◽  
Jinfang Teng
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Axial Direction ◽  
Stall Margin ◽  
Rotating Speed ◽  
Casing Treatment ◽  
Transonic Compressor ◽  
Injection Flow ◽  
Flow Through

The purpose of this work is to understand the properties of the injection flow through slots opening surfaces with steady and unsteady simulations. The feasibility of evaluating slot effectiveness by steady results is demonstrated. Transient features of injection flow are detailed investigated. Numerical investigations are carried out in a 1.5 axial transonic compressor stage at a specified rotating speed with seven kinds of slot-type casing treatments. Comparisons between steady/unsteady results show that differences of overall performance and injection mass flow rate are dependent on simulation methods, rather than slot configurations. Thus, correlation analysis by steady results of seven slot configurations is considered valid and reveals strong linear correlation between injection mass flow and stall margin improvements/efficiency drops. Therefore, it is practical to evaluate the effectiveness of a specific slot configuration in this compressor with steady results by calculating injection mass flow rate. Afterwards, unsteady simulations are performed with a specific configuration of arc-curve skewed slots. It is clarified that the dividing locations between suction/injection regions moves along the axial direction based on the relative rotor/slots location. Exchanging flow through slots opening surfaces displays periodic variations over time. The variation cycle for one single slot equals blade passing period T. For summation of mass flow through all slots, the cycle equals to T divided by slots number in one passage. The net flow rate through all opening surfaces is always less than zero during a blading passing period, i.e. injection mass flow rate is larger than suction flow all the time.

Stall Warning Using the Rotor Tip Pressure in a Transonic Axial Compressor With Circumferential Grooves

2018 ◽  
Author(s):  
Byeung Jun Lim ◽  
Tae Choon Park ◽  
Young Seok Kang
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Axial Compressor ◽  
Rotating Stall ◽  
Single Stage ◽  
Stall Inception ◽  
Casing Treatment ◽  
Stall Warning ◽  
Transonic Axial Compressor

In this study, characteristics of stall inception in a single-stage transonic axial compressor with circumferential grooves casing treatment were investigated experimentally. Additionally, the characteristic of increasing irregularity in the pressure inside circumferential grooves as the compressor approaches the stall limit was applied to the stall warning method. Spike-type rotating stall was observed in the single-stage transonic axial compressor with smooth casing. When circumferential grooves were applied, the stall inception was suppressed and the operating point of the compressor moved to lower flow rate than the stall limit. A spike-like disturbance was developed into a rotating stall cell and then the Helmholtz perturbation was overlapped on it at N = 80%. At N = 70 %, the Helmholtz perturbation was observed first and the amplitude of the wave gradually increased as mass flow rate decreased. At N = 60%, spike type stall inceptions were observed intermittently and then developed into continuous rotating stall at lower mass flow rate. Pressure measured at the bottom of circumferential grooves showed that the level of irregularity of pressure increased as flow rate decreased. Based on the characteristic of increasing irregularity of the pressure signals inside the circumferential grooves as stall approaches, an autocorrelation technique was applied to the stall warning. This technique could be used to provide warning against stall and estimate real-time stall margins in compressors with casing treatments.

Reduced-Order Modelling of Rotating Stall

2020 ◽  
Author(s):  
Dominik Schlüter ◽  
Robert P. Grewe ◽  
Fabian Wartzek ◽  
Alexander Liefke ◽  
Jan Werner ◽  
...  
Keyword(s):  
Single Cell ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Rotational Speed ◽  
Stability Limit ◽  
Rotating Stall ◽  
Operating Conditions ◽  
Transonic Compressor ◽  
Experimental Findings

Abstract Rotating stall is a non-axisymmetric disturbance in axial compressors arising at operating conditions beyond the stability limit of a stage. Although well-known, its driving mechanisms determining the number of stall cells and their rotational speed are still marginally understood. Numerical studies applying full-wheel 3D unsteady RANS calculations require weeks per operating point. This paper quantifies the capability of a more feasible quasi-2D approach to reproduce 3D rotating stall and related sensitivities. The first part of the paper deals with the validation of a numerical baseline the simplified model is compared to in detail. Therefore, 3D computations of a state-of-the-art transonic compressor are conducted. At steady conditions the single-passage RANS CFD matches the experimental results within an error of 1% in total pressure ratio and mass flow rate. At stalled conditions, the full-wheel URANS computation shows the same spiketype disturbance as the experiment. However, the CFD underpredicts the stalling point by approximately 7% in mass flow rate. In deep stall, the computational model correctly forecasts a single-cell rotating stall. The stall cell differs by approximately 21% in rotational speed and 18% in circumferential size from the experimental findings. As the 3D model reflects the compressor behaviour sufficiently accurate, it is considered valid for physical investigations. In the second part of the paper, the validated baseline is reduced in radial direction to a quasi-2D domain only resembling the compressor tip area. Four model variations regarding span-wise location and extent are numerically investigated. As the most promising model matches the 3D flow conditions in the rotor tip region, it correctly yields a single-cell rotating stall. The cell differs by only 7% in circumferential size from the 3D results. Due to the impeded radial migration in the quasi-2D slice, however, the cell exhibits an increased axial extent. It is assumed, that the axial expansion into the adjacent rows causes the difference in cell speed by approximately 24%. Further validation of the reduced model against experimental findings reveals, that it correctly reflects the sensitivity of circumferential cell size to flow coefficient and individual cell speed to compressor shaft speed. As the approach reduced the wall clock time by 92%, it can be used to increase the physical understanding of rotating stall at much lower costs.

Effect of Novel Casing Treatment on the Suppression of Stall Precursor in a Transonic Compressor

2014 ◽  
Author(s):  
Dakun Sun ◽  
Xiaofeng Sun ◽  
Xiaohua Liu ◽  
Feng Lin ◽  
Nie Chao Qun
Keyword(s):  
Perforated Plate ◽  
Area Ratio ◽  
Open Area ◽  
Stall Inception ◽  
Stall Margin ◽  
Casing Treatment ◽  
Transonic Compressor ◽  
Stall Margin Improvement ◽  
Stall Precursor ◽  
Casing Treatments

A kind of novel casing treatment is proposed to realize stall margin enhancement by suppressing stall precursor in turbomachinery. In view of its different configuration and mechanism, such casing treatment is named as stall precursor-suppressed casing treatment in the present work, or SPS casing treatment for short. In the present work, the experiments of SPS casing treatment are conducted in a transonic compressor J69 Rotor/Stage. The SPS casing treatment which consists of a backchamber and a perforated plate is designed according to a proposed theoretical model. It is noted that the open area ratio of the casing treatment is only 4–12%, which is much smaller than traditional casing treatments with over 50% open area ratio. The tests show that the SPS casing treatment can improve the stall margin by 8–12% for J69 Rotor, and 4–12% for J69 Stage. Meanwhile, the mechanism of stall margin improvement with such casing treatment will be revealed in this investigation. Comparing with the evolution of the precursors without casing treatments, the propagation of the stall inception waves will be suppressed and the non-linear development of the stall process will be delayed under the casing treatment case.

Effect of Blade Angle of Attack and Hub to Tip Ratio on Mass Flow Rate in an Axial Fan at a Fixed Rotational Speed

2008 ◽  
Author(s):  
Mohammad J. Izadi ◽  
Alireza Falahat
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Rotational Speed ◽  
Angle Of Attack ◽  
Maximum Flow ◽  
Maximum Flow Rate ◽  
Maximum Mass ◽  
Blade Angle ◽  
Axial Fan

In this investigation an attempt is made to find the best hub to tip ratio, the maximum number of blades, and the best angle of attack of an axial fan with flat blades at a fixed rotational speed for a maximum mass flow rate in a steady and turbulent conditions. In this study the blade angles are varied from 30 to 70 degrees, the hub to tip ratio is varied from 0.2 to 0.4 and the number of blades are varied from 2 to 6 at a fixed hub rotational speed. The results show that, the maximum flow rate is achieved at a blade angle of attack of about 45 degrees for when the number of blades is set equal to 4 at most rotational velocities. The numerical results show that as the hub to tip ratio is decreased, the mass flow rate is increased. For a hub to tip ratio of 0.2, and an angle of attack around 45 degrees with 4 blades, a maximum mass flow rate is achieved.

Aerodynamic Performance Evaluation of Axial Flow Fan Using Numerical Techniques

2021 ◽  
Author(s):  
Raghuvaran D. ◽  
Satvik Shenoy ◽  
Srinivas G
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Rotational Speed ◽  
Total Pressure ◽  
Axial Flow ◽  
High Mass ◽  
Ansys Fluent ◽  
Industrial Sectors ◽  
Mass Flow Rates

Abstract Axial flow fans (AFF) are extensively used in various industrial sectors, usually with flows of low resistance and high mass flow rates. The blades, the hub and the shroud are the three major parts of an AFF. Various kinds of optimisation can be implemented to improve the performance of an AFF. The most common type is found to be geometric optimisation including variation in number of blades, modification in hub and shroud radius, change in angle of attack and blade twist, etc. After validation of simulation model and carrying out a grid independence test, parametric analysis was done on an 11-bladed AFF with a shroud of uniform radius using ANSYS Fluent. The rotational speed of the fan and the velocity at fan inlet were the primary variables of the study. The variation in outlet mass flow rate and total pressure was studied for both compressible and incompressible ambient flows. Relation of mass flow rate and total pressure with inlet velocity is observed to be linear and exponential respectively. On the other hand, mass flow rate and total pressure have nearly linear relationship with rotational speed. A comparison of several different axial flow tracks with the baseline case fills one of the research gaps.

Centrifugal Compressor Performance Prediction Using Gaussian Process Regression and Artificial Neural Networks

2019 ◽  
Author(s):  
Pau Cutrina Vilalta ◽  
Hui Wan ◽  
Soumya S. Patnaik
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Centrifugal Compressor ◽  
Rotational Speed ◽  
Data Augmentation ◽  
Pressure Ratio ◽  
Gaussian Process Regression ◽  
Compressor Performance ◽  
Artificial Neural

Abstract In this paper, we use various regression models and Artificial Neural Network (ANN) to predict the centrifugal compressor performance map. Particularly, we study the accuracy and efficiency of Gaussian Process Regression (GPR) and Artificial Neural Networks in modelling the pressure ratio, given the mass flow rate and rotational speed of a centrifugal compressor. Preliminary results show that both GPR and ANN can predict the compressor performance map well, for both interpolation and extrapolation. We also study the data augmentation and data minimzation effects using the GPR. Due to the inherent pressure ratio data distribution in mass-flow-rate and rotational-speed space, data augmentation in the rotational speed is more effective to improve the ANN performance than the mass flow rate data augmentation.

Experimental Investigation of Oil Flowrate in a Hermetic Reciprocating Compressor

2014 ◽  
Author(s):  
Sibel Tas ◽  
Sertac Cadirci ◽  
Hasan Gunes ◽  
Kemal Sarioglu ◽  
Husnu Kerpicci
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Rotational Speed ◽  
High Speed ◽  
Operating Conditions ◽  
Lubricating Oil ◽  
Reciprocating Compressor ◽  
Oil Flow ◽  
Oil Flow Visualization

The aim of this experimental study is to investigate the mass flow rate of the lubricating oil in a hermetic reciprocating compressor. Essential parameters affecting the performance of the lubrication are the rotational speed of the crankshaft, the viscosity of the oil, the operating temperature and the submersion depth of the crankshaft. An experimental setup was built as to measure the oil mass flow rate with respect to the oil temperature variation during different operating conditions. The influence of the governing parameters such as the rotational speed, temperature (viscosity) and the submersion depth on the mass flow rate from crankshaft outlet are studied in detail. In addition, the oil flow visualization from the upper hole of the crankshaft is performed using a high-speed camera in order to observe the effectiveness of the lubrication of the various parts of the compressor. This study reveals that with increasing rotational speed, the submersion depth of the crankshaft and with decreasing viscosity of the lubricant, the mass flow rate from the crankshaft increases.

Surface Waviness in Abrasive Waterjet Offset-Mode Turning

2014 ◽  
Vol 599-601 ◽  
pp. 555-559
Author(s):  
Iman Zohourkari ◽  
Mehdi Zohoor ◽  
Massimiliano Annoni
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Rotational Speed ◽  
Water Pressure ◽  
Traverse Speed ◽  
Abrasive Waterjet ◽  
Depth Of Cut ◽  
Surface Waviness ◽  
Cutting Head

In this paper, surface waviness quality in abrasive waterjet offset-mode turning has been studied regarding variations of some process parameters. Influence of five main operational parameters such as water pressure, cutting head traverse speed, abrasive mass flow rate, workpiece rotational speed and depth of cut on surface waviness of turned parts have been investigated using statistical approach. Second order regression model presented for surface waviness. The model accuracy was verified by comparing with experimental data. It found that abrasive mass flow rate, cutting head traverse speed and DOC are the most influential parameters while water pressure and workpiece rotational speed show lesser effectiveness.

Stator-Rotor Interactions in a Transonic Compressor— Part 1: Effect of Blade-Row Spacing on Performance

2003 ◽  
Vol 125 (2) ◽  
pp. 328-335 ◽  
Author(s):  
Steven E. Gorrell ◽  
Theodore H. Okiishi ◽  
William W. Copenhaver
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Transonic Compressor ◽  
Blade Row ◽  
Spacing Variation ◽  
Stator Blade ◽  
Flow Compressor

Usually less axial spacing between the blade rows of an axial flow compressor is associated with improved efficiency. However, mass flow rate, pressure ratio, and efficiency all decreased as the axial spacing between the stator and rotor was reduced in a transonic compressor rig. Reductions as great as 3.3% in pressure ratio, and 1.3 points of efficiency were observed as axial spacing between the blade rows was decreased from far apart to close together. The number of blades in the stator blade-row also affected stage performance. Higher stator blade-row solidity led to larger changes in pressure ratio efficiency, and mass flow rate with axial spacing variation. Analysis of the experimental data suggests that the drop in performance is a result of increased loss production due to blade-row interactions. Losses in addition to mixing loss are present when the blade-rows are spaced closer together. The extra losses are associated with the upstream stator wakes and are most significant in the midspan region of the flow.

Sign in / Sign up

Export Citation Format

Share Document