Thermocapillarity Effects on Power-Law Liquids Thin Film Over an Unsteady Stretching Sheet

2017 ◽  
Vol 139 (12) ◽  
Author(s):  
Tingting Liu ◽  
Liancun Zheng ◽  
Yiming Ding ◽  
Lin Liu

This paper investigates the effects of thermocapillarity on the flow and heat transfer in power-law liquid film over an unsteady stretching sheet. The surface tension is assumed to vary linearly with temperature, and the thermal conductivity of the fluid is assumed power-law-dependent on the velocity gradient with modified Fourier's law. The local similarity solutions are obtained numerically, and some interesting new phenomena are found. Results indicate that the thermally induced surface tension provides an opposite force in the direction of the stretching sheet which may cause the fluid adjacent to the free surface to flow in the opposite directions. The effect of thermocapillarity tends to decrease the thin film thickness and results in a smaller temperature distribution. With the increasing unsteadiness parameter, the thin film thickness has a local maximum, and thermal boundary layer is confined to the lower part of the thin film for bigger Prandtl number, while the temperature in the thin film remains equal to the slit temperature with Prandtl number close to 0.

Energies ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 3177 ◽  
Author(s):  
Kohilavani Naganthran ◽  
Ishak Hashim ◽  
Roslinda Nazar

Thin films and coatings which have a high demand in a variety of industries—such as manufacturing, optics, and photonics—need regular improvement to sustain industrial productivity. Thus, the present work examined the problem of the Carreau thin film flow and heat transfer with the influence of thermocapillarity over an unsteady stretching sheet, numerically. The sheet is permeable, and there is an injection effect at the surface of the stretching sheet. The similarity transformation reduced the partial differential equations into a system of ordinary differential equations which is then solved numerically by the MATLAB boundary value problem solver bvp4c. The more substantial effect of injection was found to be the reduction of the film thickness at the free surface and development of a better rate of convective heat transfer. However, the increment in the thermocapillarity number thickens the film, reduces the drag force, and weakens the rate of heat transfer past the stretching sheet. The triple solutions are identified when the governing parameters vary, but two of the solutions gave negative film thickness. Detecting solutions with the most negative film thickness is essential because it implies the interruption in the laminar flow over the stretching sheet, which then affects the thin film growing process.


2016 ◽  
Vol 20 (6) ◽  
pp. 1791-1800 ◽  
Author(s):  
Yanhai Lin ◽  
Liancun Zheng ◽  
Botong Li ◽  
Xinxin Zhang

This paper presents an investigation on the MHD thin film flow and heat transfer of a power law fluid over an unsteady stretching sheet. The effects of power law viscosity on a temperature field are taken into account with a modified Fourier?s law Proposed by Zheng by assuming that the temperature field is similar to the velocity field. The governing equations are reduced to a system of nonlinear ordinary differential equations. The numerical solutions are obtained by using the shooting method coupled with the Runge-Kutta method. The influence of the Hartmann number, the power law exponent, the unsteadiness parameter, the thickness parameter and the generalized Prandtl number on the velocity and temperature fields are presented graphically and analyzed. Moreover, the critical formula for parameters are derived which indicated that the magnetic field has no effect on the critical value.


Carbon ◽  
2021 ◽  
Vol 178 ◽  
pp. 506-514
Author(s):  
Meiyu He ◽  
Jiayue Han ◽  
Xingwei Han ◽  
Jun Gou ◽  
Ming Yang ◽  
...  

2020 ◽  
Vol 102 (21) ◽  
Author(s):  
Stephan Geprägs ◽  
Björn Erik Skovdal ◽  
Monika Scheufele ◽  
Matthias Opel ◽  
Didier Wermeille ◽  
...  

Sensors ◽  
2021 ◽  
Vol 21 (12) ◽  
pp. 4056
Author(s):  
José Javier Imas ◽  
Carlos R. Zamarreño ◽  
Ignacio del Villar ◽  
Ignacio R. Matías

A fiber Bragg grating patterned on a SnO2 thin film deposited on the flat surface of a D-shaped polished optical fiber is studied in this work. The fabrication parameters of this structure were optimized to achieve a trade-off among reflected power, full width half maximum (FWHM), sensitivity to the surrounding refractive index (SRI), and figure of merit (FOM). In the first place, the influence of the thin film thickness, the cladding thickness between the core and the flat surface of the D-shaped fiber (neck), and the length of the D-shaped zone over the reflected power and the FWHM were assessed. Reflected peak powers in the range from −2 dB to −10 dB can be easily achieved with FWHM below 100 pm. In the second place, the sensitivity to the SRI, the FWHM, and the FOM were analyzed for variations of the SRI in the 1.33–1.4 range, the neck, and the thin-film thickness. The best sensitivities theoretically achieved for this device are next to 40 nm/RIU, while the best FOM has a value of 114 RIU−1.


2019 ◽  
Vol 682 ◽  
pp. 109-120 ◽  
Author(s):  
Wjatscheslaw Sakiew ◽  
Stefan Schrameyer ◽  
Marco Jupé ◽  
Philippe Schwerdtner ◽  
Nick Erhart ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document