Dynamic Modeling of the Heat Pipe-Assisted Annealing Line

2019 ◽  
Vol 141 (9) ◽  
Author(s):  
Metin Celik ◽  
Mrunal Patki ◽  
Geert Paulussen ◽  
Wiebren de Jong ◽  
Bendiks Jan Boersma
Keyword(s):  
Heat Pipe ◽  
Dynamic Simulation ◽  
Energy Efficient ◽  
Energy Savings ◽  
Steel Strip ◽  
Heat Pipes ◽  
Building Blocks ◽  
Continuous Annealing ◽  
Strip Line ◽  
Simulation Results

In a conventional continuous annealing line, the energy supplied to steel strip during heating is not recovered while cooling it. Therefore, an alternative heat transfer technology for energy efficient continuous annealing of steel was developed. This technology enables reusing the heat extracted during cooling of the strip in the heating part of the process. This is achieved by thermally linking the cooling strip to the heating strip via multiple rotating heat pipes. In this context, the dynamic simulation of a full heat pipe assisted annealing line is performed. The dynamic simulation consists of the interaction of computational building blocks, each comprising of a rotating heat pipe and strip parts wrapped around the heat pipe. The simulations are run for different installation configurations and operational settings, with the heat pipe number varying between 50 and 100 and with varying strip line speed and dimensions. The heat pipes are sized to be 0.5 m in diameter and 3 m in length. The simulation results show that the equipment is capable of satisfying the thermal cycle requirements of annealing both at steady-state and during transition between steady-states following changes in boundary conditions. With this concept, energy savings of up to 70% are feasible.

scholarly journals Comparative analysis of selected glass systems by dynamic simulation using measured real environmental conditions

2020 ◽  
Vol 172 ◽  
pp. 19009
Author(s):  
Silvia Bizoňová ◽  
Dušan Katunský ◽  
Miloslav Bagoňa
Keyword(s):  
Dynamic Simulation ◽  
Energy Savings ◽  
Building Envelope ◽  
Heat Losses ◽  
Experimental Glass ◽  
Existing Structures ◽  
Spectrally Selective ◽  
The Subject ◽  
Simulation Results ◽  
Made In

The subject of the study presents the measurement of temperatures on surfaces of glass systems of existing structures and the surfaces of experimental glass systems obtained by dynamic simulation. Measurements were made in the test cells of the Faculty of Civil Engineering of the Technical University of Košice. The partial results of which are the basis for the comparison of the currently installed and experimentally designed glass systems using spectrally selective films. The proposed mathematical-physical model was simplified by replacing the sash, frame and its components with a homogenous element with minimal shape modifications, while this does not have a significant effect on the simulation results. The choice of the proposed glass system respects the need for reduction of solar gains in summer and heat losses in buildings in winter through the weakest part of the building envelope and indicates future energy savings in relation to cooling and heating costs with a view to optimizing light and thermal comfort.

scholarly journals Testing algorithm for heat transfer performance of nanofluid-filled heat pipe based on neural network

Open Physics ◽  
2020 ◽  
Vol 18 (1) ◽  
pp. 751-760
Author(s):  
Lei Lei
Keyword(s):  
Neural Network ◽  
Heat Transfer ◽  
Heat Pipe ◽  
Heat Transfer Performance ◽  
Volume Fraction ◽  
Heat Pipes ◽  
Transfer Performance ◽  
Analysis Model ◽  
Accurate Analysis ◽  
Testing Algorithm

AbstractTraditional testing algorithm based on pattern matching is impossible to effectively analyze the heat transfer performance of heat pipes filled with different concentrations of nanofluids, so the testing algorithm for heat transfer performance of a nanofluidic heat pipe based on neural network is proposed. Nanofluids are obtained by weighing, preparing, stirring, standing and shaking using dichotomy. Based on this, the heat transfer performance analysis model of the nanofluidic heat pipe based on artificial neural network is constructed, which is applied to the analysis of heat transfer performance of nanofluidic heat pipes to achieve accurate analysis. The experimental results show that the proposed algorithm can effectively analyze the heat transfer performance of heat pipes under different concentrations of nanofluids, and the heat transfer performance of heat pipes is best when the volume fraction of nanofluids is 0.15%.

scholarly journals Low-Power Multiplexer Structures Targeting Efficient QCA Nanotechnology Circuit Designs

Electronics ◽  
2021 ◽  
Vol 10 (16) ◽  
pp. 1885
Author(s):  
Amjad Almatrood ◽  
Aby K. George ◽  
Harpreet Singh
Keyword(s):  
Energy Efficient ◽  
Building Blocks ◽  
Switching Frequency ◽  
Circuit Implementation ◽  
Suitable Candidate ◽  
Quantum Dot Cellular Automata ◽  
Performance Factors ◽  
Integration Density ◽  
Qca Circuits ◽  
Energy Efficient Building

Quantum-dot cellular automata (QCA) technology is considered to be a possible alternative for circuit implementation in terms of energy efficiency, integration density and switching frequency. Multiplexer (MUX) can be considered to be a suitable candidate for designing QCA circuits. In this paper, two different structures of energy-efficient 2×1 MUX designs are proposed. These MUXes outperform the best existing design in terms of power consumption with approximate reductions of 26% and 35%. Moreover, similar or better performance factors such as area and latency are achieved compared to the available designs. These MUX structures can be used as fundamental energy-efficient building blocks for replacing the majority-based structures in QCA. The scalability property of the proposed MUXes is excellent and can be used for energy-efficient complex QCA circuit designs.

Inverse Kinematic Solution and Dynamic Model to 3PTT Parallel Mechanism

2014 ◽  
Vol 945-949 ◽  
pp. 1421-1425
Author(s):  
Xiu Qing Hao
Keyword(s):  
Dynamic Model ◽  
Dynamic Simulation ◽  
Parallel Mechanism ◽  
Inverse Kinematic ◽  
Euler Method ◽  
Research Subject ◽  
Adams Software ◽  
Inverse Kinematic Analysis ◽  
Simulation Results ◽  
Kinematic Solution

Take typical parallel mechanism 3PTT as research subject, its inverse kinematic analysis solution was gotten. Dynamic model of the mechanism was established by Newton-Euler method, and the force and torque equations were derived. Dynamic simulation of 3PTT parallel mechanism was done by using ADAMS software, and simulation results have verified the correctness of the theoretical conclusions.

The Heat Transport Capacity of Micro Heat Pipes

1998 ◽  
Vol 120 (4) ◽  
pp. 1064-1071 ◽  
Author(s):  
J. M. Ha ◽  
G. P. Peterson
Keyword(s):  
Experimental Data ◽  
Heat Pipe ◽  
Heat Transport ◽  
Heat Pipes ◽  
Original Model ◽  
Semiempirical Model ◽  
Transport Capacity ◽  
Predictive Tool ◽  
Maximum Heat ◽  
Micro Heat Pipes

The original analytical model for predicting the maximum heat transport capacity in micro heat pipes, as developed by Cotter, has been re-evaluated in light of the currently available experimental data. As is the case for most models, the original model assumed a fixed evaporator region and while it yields trends that are consistent with the experimental results, it significantly overpredicts the maximum heat transport capacity. In an effort to provide a more accurate predictive tool, a semi-empirical correlation has been developed. This modified model incorporates the effects of the temporal intrusion of the evaporating region into the adiabatic section of the heat pipe, which occurs as the heat pipe approaches dryout conditions. In so doing, the current model provides a more realistic picture of the actual physical situation. In addition to incorporating these effects, Cotter’s original expression for the liquid flow shape factor has been modified. These modifications are then incorporated into the original model and the results compared with the available experimental data. The results of this comparison indicate that the new semiempirical model significantly improves the correlation between the experimental and predicted results and more accurately represents the actual physical behavior of these devices.

Synchronreluktanz-Motorspindeln in Werkzeugmaschinen*/Synchronous reluctance motor spindles in machine tools – Energy-efficient drives increase accuracy and reduce cooling requirements of machining centers

2019 ◽  
Vol 109 (01-02) ◽  
pp. 72-80
Author(s):  
M. Weber ◽  
M. Helfert ◽  
F. Unterderweide ◽  
E. Abele ◽  
M. Weigold
Keyword(s):  
Thermal Management ◽  
Energy Efficient ◽  
Machine Tools ◽  
Production Management ◽  
Energy Savings ◽  
Cooling System ◽  
Holistic View ◽  
Synchronous Reluctance Motor ◽  
Management Technology ◽  
Reluctance Motor

Im Rahmen des vom Bundesministerium für Wirtschaft und Energie (BMWi) geförderten Projekts „ETA-Fabrik“ am Institut für Produktionsmanagement, Technologie und Werkzeugmaschinen (PTW) der Technischen Universität Darmstadt konnte die Energieeffizienz von Motorspindeln als Hauptenergieverbraucher von Werkzeugmaschinen durch Einsatz der Synchronreluktanztechnologie gesteigert werden. In der Konsequenz ergeben sich weitere Energieeinsparpotenziale und produktionstechnische Vorteile durch eine gesamtenergetische Betrachtung der Werkzeugmaschine mit Kühlsystem und intelligentem Spindelthermomanagement.   As part of the ‘ETA-Fabrik’ project funded by the BMWi, the Institute of Production Management, Technology and Machine Tools (PTW) of the TU Darmstadt has used synchronous reluctance drives to increase the energy efficiency of motor spindles as main energy consumers of machine tools. Subsequently, new opportunities for energy savings and advantages for the manufacturing process arise by taking a holistic view on machine tools including the cooling system, proposing an intelligent spindle thermal management.

A Numerical Analysis of Gas Turbine Disks Incorporating Rotating Heat Pipes

2000 ◽  
Author(s):  
Y. Cao ◽  
J. Ling ◽  
R. Rivir ◽  
C. MacArthur
Keyword(s):  
Heat Pipe ◽  
Gas Turbine ◽  
Heat Pipes ◽  
High Heat ◽  
Thermal Dissipation ◽  
High Heat Flux ◽  
Heating And Cooling ◽  
Turbine Disks ◽  
Higher Temperature ◽  
Lower Temperature

Abstract Radially rotating heat pipes have been proposed for cooling gas turbine disks working at high temperatures. A disk incorporating the heat pipe would have an enhanced thermal dissipation capacity and a much lower temperature at the disk rim and dovetail surface. In this paper, extensive numerical simulations have been made for heat-pipe-cooled disks. Thermal performances are compared for the disks with and without incorporating the heat pipe at different heating and cooling conditions. The numerical results presented in this paper indicate that radially rotating heat pipes can significantly reduce the maximum and average temperatures at the disk rim and dovetail surface under a high heat flux working condition. In general, the maximum and average temperatures at the disk rim and dovetail surface could be reduced by above 250 and 150 degrees, respectively, compared to those of the disk without the heat pipe. As a result, a disk incorporating radially rotating heat pipes could alleviate temperature-related problems and allow a gas turbine to work at a much higher temperature.

Sign in / Sign up

Export Citation Format

Share Document