Comparison of under-actuated and fully-actuated serial robotic arms: a case study

2021 ◽  
pp. 1-13
Author(s):  
Matteo Bottin ◽  
Giulio Rosati
Keyword(s):  
Degrees Of Freedom ◽  
Simple Point ◽  
Controllable System ◽  
Robotic Arms ◽  
Passive Joint ◽  
Final Configuration ◽  
Vibration Behavior ◽  
Rotational Joint ◽  
Point To Point

Abstract Under-actuated robots are very interesting in terms of cost and weight since they can result in a state-controllable system with a number of actuators lower than the number of joints. In this paper, a comparison between an under-actuated planar 3 degrees of freedom (DOF) robot and a comparable fully-actuated 2 degrees of freedom robot is presented, mainly focusing on the performances in terms of trajectories, actuator torques, and vibrations. The under-actuated system is composed of 2 active rotational joints followed by a passive rotational joint equipped with a torsional spring. The fully-actuated robot is inertial equivalent to the under-actuated manipulator: the last link is equal to the sum of the last two links of the under-actuated system. Due to the conditions on the inertia distribution and spring placement, in a simple point-to-point movement the last passive joint starts and ends in a zero-value configuration, so the 3 DOF robot is equivalent, in terms of initial and final configuration, to the 2 DOF fully-actuated robot, thus they can be compared. Results show how while the fully actuated robot is better in terms of reliable trajectory and actuator torques, the under-actuated robot wins in flexibility and vibration behavior.

scholarly journals Hybrid Seven-bar Press Mechanism

2018 ◽  
Vol 12 (3) ◽  
pp. 181-187
Author(s):  
M. Erkan Kütük ◽  
L. Canan Dülger
Keyword(s):  
Genetic Algorithm ◽  
Objective Function ◽  
Design Optimization ◽  
Hybrid System ◽  
Degrees Of Freedom ◽  
Dimensional Synthesis ◽  
Design Variables ◽  
Optimization Study ◽  
Metal Stamping

An optimization study with kinetostatic analysis is performed on hybrid seven-bar press mechanism. This study is based on previous studies performed on planar hybrid seven-bar linkage. Dimensional synthesis is performed, and optimum link lengths for the mechanism are found. Optimization study is performed by using genetic algorithm (GA). Genetic Algorithm Toolbox is used with Optimization Toolbox in MATLAB®. The design variables and the constraints are used during design optimization. The objective function is determined and eight precision points are used. A seven-bar linkage system with two degrees of freedom is chosen as an example. Metal stamping operation with a dwell is taken as the case study. Having completed optimization, the kinetostatic analysis is performed. All forces on the links and the crank torques are calculated on the hybrid system with the optimized link lengths

Complete Accessibility of Oscillations in Robotic Systems by Orthogonal Projections

1990 ◽  
Vol 112 (2) ◽  
pp. 194-202 ◽  
Author(s):  
Sabri Tosunoglu ◽  
Shyng-Her Lin ◽  
Delbert Tesar
Keyword(s):  
Current Practice ◽  
Industrial Robot ◽  
Robotic Systems ◽  
Orthogonal Projections ◽  
Small Oscillations ◽  
Robotic Arms ◽  
Driven System ◽  
System Equations ◽  
Six Degree Of Freedom

The current practice of controller development for flexible robotic systems generally focuses on one-link robotic arms and is valid for small oscillations. This work addresses the control of n-link, serial, spatial robotic systems modeled with m1 joint and m2 link flexibilities such that n≥m1+m2. System compliance is modeled by local springs and nonactuated prismatic and revolute type pseudo joints. The coupled, nonlinear, error-driven system equations are derived for the complete model without linearization or neglecting certain terms. For this system, the complete accessibility of vibrations is studied by orthogonal projections. It is shown that under some configurations of a robotic system, the induced oscillations may not be accessible to the controller. Given accessibility, the controller developed in this work assures the global asymptotic stability of the system. Example numerical simulations are presented based on the model of a six-degree-of-freedom Cincinnati Milacron T3-776 industrial robot. One example models the system compliance in four joints, while another case study simulates four lateral link oscillations. These examples show that this controller, even under inaccurate payload description, eliminates the oscillations while tracking desired trajectories.

Laboratory performance of wi-fi point-to-point links: A case study

2009 ◽  
Author(s):  
J.A.R.P. de Carvalho ◽  
H. Veiga ◽  
P. Gomes ◽  
C.F.F.P.R. Pacheco ◽  
N. Marques ◽  
...  
Keyword(s):  
Laboratory Performance ◽  
Point To Point

Interface Reduction in Craig-Bampton Component Mode Synthesis by Orthogonal Polynomial Series

2017 ◽  
Author(s):  
Luigi Carassale ◽  
Mirko Maurici
Keyword(s):  
Degrees Of Freedom ◽  
Axial Compressor ◽  
Component Mode Synthesis ◽  
Reduction Techniques ◽  
Interface Reduction ◽  
Reduction Methods ◽  
Interface Displacement ◽  
Polynomial Series ◽  
Efficient Representation

The component mode synthesis based on the Craig-Bampton method has two strong limitations that appear when the number of the interface degrees of freedom is large. First, the reduced-order model obtained is overweighed by many unnecessary degrees of freedom. Second, the reduction step may become extremely time consuming. Several interface reduction techniques addressed successfully the former problem, while the latter remains open. In this paper we tackle this latter problem through a simple interface-reduction technique based on an a-priory choice of the interface modes. An efficient representation of the interface displacement field is achieved adopting a set of orthogonal basis functions determined by the interface geometry. The proposed method is compared with other existing interface reduction methods on a case study regarding a rotor blade of an axial compressor.

Kinematics Analysis and Motion Control of a Mobile Robot Driven by Three Tracked Vehicles

2018 ◽  
Author(s):  
Xin-Jun Liu ◽  
Zhao Gong ◽  
Fugui Xie ◽  
Shuzhan Shentu
Keyword(s):  
Mobile Robot ◽  
Motion Planning ◽  
Degrees Of Freedom ◽  
Inverse Kinematic ◽  
Planning Method ◽  
Tracked Vehicles ◽  
Loop Control ◽  
Point Motion ◽  
Point To Point ◽  
Motion Mode

In this paper, a mobile robot named VicRoB with 6 degrees of freedom (DOFs) driven by three tracked vehicles is designed and analyzed. The robot employs a 3-PPSR parallel configuration. The scheme of the mechanism and the inverse kinematic solution are given. A path planning method of a single tracked vehicle and a coordinated motion planning of three tracked vehicles are proposed. The mechanical structure and the electrical architecture of VicRoB prototype are illustrated. VicRoB can achieve the point-to-point motion mode and the continuous motion mode with employing the motion planning method. The orientation precision of VicRoB is measured in a series of motion experiments, which verifies the feasibility of the motion planning method. This work provides a kinematic basis for the orientation closed loop control of VicRoB whether it works on flat or rough road.

scholarly journals Planning Fail-Safe Trajectories for Space Robotic Arms

2021 ◽  
Vol 8 ◽  
Author(s):  
Oliver Porges ◽  
Daniel Leidner ◽  
Máximo A. Roa
Keyword(s):  
Degrees Of Freedom ◽  
Fault Tolerant ◽  
Robotic Manipulators ◽  
Task Completion ◽  
Joint Failure ◽  
Space Applications ◽  
Robotic Arms ◽  
Hazardous Environments ◽  
Potential Risks ◽  
Fail Safe

A frequent concern for robot manipulators deployed in dangerous and hazardous environments for humans is the reliability of task executions in the event of a joint failure. A redundant robotic manipulator can be used to mitigate the risk and guarantee a post-failure task completion, which is critical for instance for space applications. This paper describes methods to analyze potential risks due to a joint failure, and introduces tools for fault-tolerant task design and path planning for robotic manipulators. The presented methods are based on off-line precomputed workspace models. The methods are general enough to cope with robots with any type of joint (revolute or prismatic) and any number of degrees of freedom, and might include arbitrarily shaped obstacles in the process, without resorting to simplified models. Application examples illustrate the potential of the approach.

Trajectory Synthesis and Redundancy Resolution for High Speed Point to Point Motions of Redundant Robot Manipulators

1997 ◽  
Author(s):  
W. Kim ◽  
J. Rastegar
Keyword(s):  
High Speed ◽  
Degrees Of Freedom ◽  
Robot Manipulator ◽  
Robot Manipulators ◽  
Dynamic Performance ◽  
High Harmonic ◽  
Harmonic Excitation ◽  
Redundancy Resolution ◽  
Tracking Accuracy ◽  
Point To Point

Abstract Trajectory synthesis for robot manipulators with redundant kinematic degrees-of-freedom has been studied by numerous investigators. Redundant manipulators are of interest since the redundant degrees-of-freedom can be used to improve the local and global kinematic and dynamic performance of a system. As a robot manipulator is forced to track a given trajectory, the required actuating torques (forces) may excite the natural modes of vibration of the system. Noting that manipulators with revolute joints have nonlinear dynamics, high harmonic excitation torques are generally generated even though such harmonics have been eliminated from the synthesized trajectories and filtered from the drive inputs. In this paper, a redundancy resolution method is developed based on the Trajectory Pattern Method (TPM) to synthesize trajectories such that the actuating torques required to realize them do not contain higher harmonic components with significant amplitudes. With such trajectories, a robot manipulator can operate at higher speeds and achieve higher tracking accuracy with suppressed residual vibration. As an example, optimal trajectories are synthesized for point to point motions of a plane 3R manipulator.

Piezothermoelasticity and Control of Piezoelectric Laminates Exposed to a Steady-State Temperature Field

1993 ◽  
Author(s):  
H. S. Tzou ◽  
R. Ye
Keyword(s):  
Temperature Field ◽  
Steady State ◽  
Degrees Of Freedom ◽  
Sensors And Actuators ◽  
System Equation ◽  
Thermal Fields ◽  
Steady State Temperature ◽  
And Control ◽  
Internal Degrees Of Freedom

Abstract Piezothermoelastic effects of distributed piezoelectric sensors and actuators are investigated. Vibration control of piezoelectric laminates subjected to a steady-state temperature field is studied. A new 3-D piezothermoelastic finite element with three internal degrees of freedom is formulated using a variational formulation. A system equation for the piezoelectric continuum exposed to combined elastic, electric, and thermal fields is formulated. Distributed sensing and control equations are derived. All these effects are studied in a case study.

Study of grasp-energy based optimal distribution of contact forces on a humanoid robotic hand during object grasp

Robotica ◽  
2021 ◽  
pp. 1-26
Author(s):  
Sourajit Mukherjee ◽  
Abhijit Mahapatra ◽  
Amit Kumar ◽  
Avik Chatterjee
Keyword(s):  
Optimization Algorithm ◽  
Degrees Of Freedom ◽  
Simulated Data ◽  
Performance Measure ◽  
Contact Forces ◽  
Contact Model ◽  
Robotic Hand ◽  
Net Energy ◽  
Optimal Distribution

Abstract A novel grasp optimization algorithm for minimizing the net energy utilized by a five-fingered humanoid robotic hand with twenty degrees of freedom for securing a precise grasp is presented in this study. The algorithm utilizes a compliant contact model with a nonlinear spring and damper system to compute the performance measure, called ‘Grasp Energy’. The measure, subject to constraints, has been minimized to obtain locally optimal cartesian trajectories for securing a grasp. A case study is taken to compare the analytical (applying the optimization algorithm) and the simulated data in MSC.Adams $^{^{\circledR}}$ , to prove the efficacy of the proposed formulation.

scholarly journals Analysis of Upper-Limb and Trunk Kinematic Variability: Accuracy and Reliability of an RGB-D Sensor

2020 ◽  
Vol 4 (2) ◽  
pp. 14
Author(s):  
Alessandro Scano ◽  
Robert Mihai Mira ◽  
Pietro Cerveri ◽  
Lorenzo Molinari Tosatti ◽  
Marco Sacco
Keyword(s):  
Upper Limb ◽  
Gold Standard ◽  
Degrees Of Freedom ◽  
Cost Effective ◽  
Human Motion ◽  
Working Environments ◽  
Wide Range ◽  
Upper Limb Movements ◽  
Clinical Environments ◽  
Point To Point

In the field of motion analysis, the gold standard devices are marker-based tracking systems. Despite being very accurate, their cost, stringent working environments, and long preparation time make them unsuitable for small clinics as well as for other scenarios such as industrial application. Since human-centered approaches have been promoted even outside clinical environments, the need for easy-to-use solutions to track human motion is topical. In this context, cost-effective devices, such as RGB-Depth (RBG-D) cameras have been proposed, aiming at a user-centered evaluation in rehabilitation or of workers in industry environment. In this paper, we aimed at comparing marker-based systems and RGB-D cameras for tracking human motion. We used a Vicon system (Vicon Motion Systems, Oxford, UK) as a gold standard for the analysis of accuracy and reliability of the Kinect V2 (Microsoft, Redmond, WA, USA) in a variety of gestures in the upper limb workspace—targeting rehabilitation and working applications. The comparison was performed on a group of 15 adult healthy subjects. Each subject had to perform two types of upper-limb movements (point-to-point and exploration) in three workspace sectors (central, right, and left) that might be explored in rehabilitation and industrial working scenarios. The protocol was conceived to test a wide range of the field of view of the RGB-D device. Our results, detailed in the paper, suggest that RGB-D sensors are adequate to track the upper limb for biomechanical assessments, even though relevant limitations can be found in the assessment and reliability of some specific degrees of freedom and gestures with respect to marker-based systems.

Sign in / Sign up

Export Citation Format

Share Document