scholarly journals Experimental Investigation of Boundary Layer Behavior in a Simulated Low Pressure Turbine

1999 ◽  
Vol 122 (1) ◽  
pp. 84-89 ◽  
Author(s):  
Rickey J. Shyne ◽  
Ki-Hyeon Sohn ◽  
Kenneth J. De Witt
Keyword(s):  
Boundary Layer ◽  
Separation Bubble ◽  
Flow Region ◽  
Suction Side ◽  
Low Pressure ◽  
Careful Examination ◽  
Freestream Turbulence ◽  
Free Shear Layer ◽  
Mean Velocity ◽  
Low Pressure Turbine

A detailed investigation of the flow physics occurring on the suction side of a simulated low pressure turbine (LPT) blade was performed. A contoured upper wall was designed to simulate the pressure distribution of an actual LPT blade onto a flat plate. The experiments were carried out at Reynolds numbers of 100,000 and 250,000 with three levels of freestream turbulence. The main emphasis in this paper is placed on flow field surveys performed at a Reynolds number of 100,000 with levels of freestream turbulence ranging from 0.8 percent to 3 percent. Smoke-wire flow visualization data were used to confirm that the boundary layer was separated and formed a bubble. The transition process over the separated flow region is observed to be similar to a laminar free shear layer flow with the formation of a large coherent eddy structure. For each condition, the locations defining the separation bubble were determined by careful examination of pressure and mean velocity profile data. Transition onset location and length determined from intermittency profiles decrease as freestream turbulence levels increase. Additionally, the length and height of the laminar separation bubbles were observed to be inversely proportional to the levels of freestream turbulence. [S0098-2202(00)00701-X]

scholarly journals Experimental Investigation of Boundary Layer Behavior in a Simulated Low Pressure Turbine

1998 ◽  
Author(s):  
Ki H. Sohn ◽  
Rickey J. Shyne ◽  
Kenneth J. DeWitt
Keyword(s):  
Boundary Layer ◽  
Separation Bubble ◽  
Flow Region ◽  
Suction Side ◽  
Low Pressure ◽  
Careful Examination ◽  
Freestream Turbulence ◽  
Free Shear Layer ◽  
Mean Velocity ◽  
Low Pressure Turbine

A detailed investigation of the flow physics occurring on the suction side of a simulated Low Pressure Turbine (LPT) blade was performed. A contoured upper wall was designed to simulate the pressure distribution of an actual LPT blade onto a flat plate. The experiments were carried out at Reynolds numbers of 100,000 and 250,000 with three levels of freestream turbulence. The main emphasis in this paper is placed on flow field surveys performed at a Reynolds number of 100,000 with levels of freestream turbulence ranging from 0.8% to 3%. Smoke-wire flow visualization data was used to confirm that the boundary layer was separated and formed a bubble. The transition process over the separated flow region is observed to be similar to a laminar free shear layer flow with the formation of a large coherent eddy structure. For each condition, the locations defining the separation bubble were determined by careful examination of pressure and mean velocity profile data. Transition onset location and length determined from intermittency profiles decrease as freestream turbulence levels increase. Additionally, the length and height of the laminar separation bubbles were observed to be inversely proportional to the levels of freestream turbulence.

Aerodynamic Measurements on a Low Pressure Turbine Cascade With Different Levels of Distributed Roughness

2011 ◽  
Author(s):  
Marco Montis ◽  
Reinhard Niehuis ◽  
Andreas Fiala
Keyword(s):  
Boundary Layer ◽  
High Speed ◽  
Separation Bubble ◽  
Reference Conditions ◽  
Suction Side ◽  
Boundary Layer Separation ◽  
Low Pressure ◽  
Average Roughness ◽  
Low Pressure Turbine ◽  
High Reynolds

The effect of surface roughness on the aerodynamics of a highly loaded low-pressure turbine airfoil was investigated in a series of cascade tests conducted in a high speed facility. Profile loss and aerodynamic loading of three different surface roughnesses with a ratio of the centerline average roughness to the profile chord of 1.1 · 10−5, 7.1 · 10−5 and 29 · 10−5 were analysed. Tests were carried out under design outlet Mach number, outlet Reynolds number ranging from 5 · 104 to 7 · 105 and inlet turbulence level of 2.5% and 5%. The mid span flow field downstream of the cascade and the loading distribution on the profile were measured for each investigated operating point using a five hole probe and surface static pressure taps. Additional measurements with a hot wire probe in the profile boundary layer under reference conditions (Re2th = 2 · 105) were also conducted. Experimental results show a loss reduction for the highest roughness under reference conditions, due to the partial suppression of the separation bubble on the suction side of the profile. At high Reynolds numbers a massive boundary layer separation on the suction side is observed for the highest roughness, along with a large increase in total pressure loss. The middle roughness tested has no effect on the loading distribution as well as on the loss behaviour of the airfoil under all investigated flow conditions.

Separated Flow Transition in a Low Pressure Turbine Cascade: Mean Flow and Turbulence Spectra

2003 ◽  
Author(s):  
Ralph J. Volino ◽  
Christopher G. Murawski
Keyword(s):  
Boundary Layer ◽  
Free Stream ◽  
Separation Bubble ◽  
Suction Side ◽  
Low Pressure ◽  
Turbine Cascade ◽  
Mean Flow ◽  
Turbulence Spectra ◽  
Free Stream Turbulence ◽  
Low Pressure Turbine

Boundary layer separation, transition and reattachment have been studied experimentally in a low-pressure turbine cascade. Cases with Reynolds numbers (Re) ranging from 50,000 to 200,000 (based on suction surface length and exit velocity) have been considered under low free-stream turbulence conditions. Mean and fluctuating velocity profiles and turbulence spectra are presented for streamwise locations along the suction side of one airfoil and in the wake downstream of the airfoils. Hot film gages on the suction side surface of the airfoil are used to measure the fluctuation level and the spectra of the fluctuations on the surface. Higher Re moves transition upstream. Transition is initiated in the shear layer over the separation bubble and leads to boundary layer reattachment. Peak frequencies in the boundary layer spectra match those found in similar cases in the literature, indicating that the important frequencies may be predictable. Spectra in the wake downstream of the airfoils were similar to the spectra in the boundary layer near the trailing edge of the airfoil. Comparisons to the literature indicate that small but measurable differences in the spectra of the low free-stream turbulence can have a significant effect on boundary layer reattachment.

Experimental and Computational Investigations of Separation and Transition on a Highly Loaded Low-Pressure Turbine Airfoil: Part 2 — High Freestream Turbulence Intensity

2008 ◽  
Author(s):  
Ralph J. Volino ◽  
Olga Kartuzova ◽  
Mounir B. Ibrahim
Keyword(s):  
Boundary Layer ◽  
Shear Stress ◽  
Shear Layer ◽  
Separation Bubble ◽  
Reynolds Numbers ◽  
Low Pressure ◽  
Transition Model ◽  
Freestream Turbulence ◽  
Low Pressure Turbine ◽  
Separated Shear Layer

Boundary layer separation, transition and reattachment have been studied on a very high lift, low-pressure turbine airfoil. Experiments were done under high (4%) freestream turbulence conditions on a linear cascade in a low speed wind tunnel. Pressure surveys on the airfoil surface and downstream total pressure loss surveys were documented. Velocity profiles were acquired in the suction side boundary layer at several streamwise locations using hot-wire anemometry. Cases were considered at Reynolds numbers (based on the suction surface length and the nominal exit velocity from the cascade) ranging from 25,000 to 300,000. At the lowest Reynolds number the boundary layer separated and did not reattach, in spite of transition in the separated shear layer. At higher Reynolds numbers the boundary layer did reattach, and the separation bubble became smaller as Re increased. High freestream turbulence increased the thickness of the separated shear layer, resulting in a thinner separation bubble. This effect resulted in reattachment at intermediate Reynolds numbers, which was not observed at the same Re under low freestream turbulence conditions. Numerical simulations were performed using an unsteady Reynolds averaged Navier-Stokes (URANS) code with both a shear stress transport k-ω model and a 4 equation shear stress transport Transition model. Both models correctly predicted separation and reattachment (if it occurred) at all Reynolds numbers. The Transition model generally provided better quantitative results, correctly predicting velocities, pressure, and separation and transition locations. The model also correctly predicted the difference between high and low freestream turbulence cases.

Experimental and Computational Investigations of Separation and Transition on a Highly Loaded Low-Pressure Turbine Airfoil: Part 1 — Low Freestream Turbulence Intensity

2008 ◽  
Author(s):  
Mounir Ibrahim ◽  
Olga Kartuzova ◽  
Ralph J. Volino
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Transport Model ◽  
Separation Bubble ◽  
Pressure Coefficient ◽  
Low Pressure ◽  
Transition To Turbulence ◽  
Transition Model ◽  
Freestream Turbulence ◽  
Low Pressure Turbine

Boundary layer separation, transition and reattachment have been studied on a new, very high lift, low-pressure turbine airfoil. Experiments were done under low freestream turbulence conditions on a linear cascade in a low speed wind tunnel. Pressure surveys on the airfoil surface and downstream total pressure loss surveys were documented. Velocity profiles were acquired in the suction side boundary layer at several streamwise locations using hot-wire anemometry. Cases were considered at Reynolds numbers (based on the suction surface length and the nominal exit velocity from the cascade) ranging from 25,000 to 330,000. In all cases the boundary layer separated, but at high Reynolds number the separation bubble remained very thin and quickly reattached after transition to turbulence. In the low Reynolds number cases, the boundary layer separated and did not reattach, even when transition occurred. Three different CFD URANS (unsteady Reynolds averaged Navier-Stokes) models were utilized in this study (using Fluent CFD Code), the k-ω shear stress transport model, the ν2-fk-ε model, and the 4 equation Transition model of Menter. At Re = 25,000, the Transition model seems to perform the best. At Re = 100,000 the Transition model seems to perform the best also, although it under-predicts the pressure coefficient downstream of the suction peak. At Re = 300,000 all models perform very similar with each other. The Transition model showed a small bump in the pressure coefficient downstream from the suction peak indicating the presence of a small bubble at that location.

scholarly journals Measurements in Separated and Transitional Boundary Layers Under Low-Pressure Turbine Airfoil Conditions

2000 ◽  
Vol 123 (2) ◽  
pp. 189-197 ◽  
Author(s):  
Ralph J. Volino ◽  
Lennart S. Hultgren
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Pressure Gradient ◽  
Boundary Layers ◽  
Free Stream ◽  
Separation Bubble ◽  
Low Pressure ◽  
Mean Velocity ◽  
Free Stream Turbulence ◽  
Low Pressure Turbine

Detailed velocity measurements were made along a flat plate subject to the same dimensionless pressure gradient as the suction side of a modern low-pressure turbine airfoil. Reynolds numbers based on wetted plate length and nominal exit velocity were varied from 50,000 to 300,000, covering cruise to takeoff conditions. Low and high inlet free-stream turbulence intensities (0.2 and 7 percent) were set using passive grids. The location of boundary-layer separation does not depend strongly on the free-stream turbulence level or Reynolds number, as long as the boundary layer remains nonturbulent prior to separation. Strong acceleration prevents transition on the upstream part of the plate in all cases. Both free-stream turbulence and Reynolds number have strong effects on transition in the adverse pressure gradient region. Under low free-stream turbulence conditions, transition is induced by instability waves in the shear layer of the separation bubble. Reattachment generally occurs at the transition start. At Re=50,000 the separation bubble does not close before the trailing edge of the modeled airfoil. At higher Re, transition moves upstream, and the boundary layer reattaches. With high free-stream turbulence levels, transition appears to occur in a bypass mode, similar to that in attached boundary layers. Transition moves upstream, resulting in shorter separation regions. At Re above 200,000, transition begins before separation. Mean velocity, turbulence, and intermittency profiles are presented.

scholarly journals Measurements in Separated and Transitional Boundary Layers Under Low-Pressure Turbine Airfoil Conditions

2000 ◽  
Author(s):  
Ralph J. Volino ◽  
Lennart S. Hultgren
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Pressure Gradient ◽  
Boundary Layers ◽  
Free Stream ◽  
Separation Bubble ◽  
Low Pressure ◽  
Mean Velocity ◽  
Free Stream Turbulence ◽  
Low Pressure Turbine

Detailed velocity measurements were made along a flat plate subject to the same dimensionless pressure gradient as the suction side of a modern low-pressure turbine airfoil. Reynolds numbers based on wetted plate length and nominal exit velocity were varied from 50, 000 to 300, 000, covering cruise to takeoff conditions. Low and high inlet free-stream turbulence intensities (0.2% and 7%) were set using passive grids. The location of boundary-layer separation does not depend strongly on the free-stream turbulence level or Reynolds number, as long as the boundary layer remains non-turbulent prior to separation. Strong acceleration prevents transition on the upstream part of the plate in all cases. Both free-stream turbulence and Reynolds number have strong effects on transition in the adverse pressure gradient region. Under low free-stream turbulence conditions transition is induced by instability waves in the shear layer of the separation bubble. Reattachment generally occurs at the transition start. At Re = 50, 000 the separation bubble does not close before the trailing edge of the modeled airfoil. At higher Re, transition moves upstream, and the boundary layer reattaches. With high free-stream turbulence levels, transition appears to occur in a bypass mode, similar to that in attached boundary layers. Transition moves upstream, resulting in shorter separation regions. At Re above 200,000, transition begins before separation. Mean velocity, turbulence and intermittency profiles are presented.

An Experimental Investigation of the Wake Shed From a High-Lift Low Pressure Turbine Cascade at Different Reynolds Numbers

2008 ◽  
Author(s):  
Francesca Satta ◽  
Marina Ubaldi ◽  
Pietro Zunino ◽  
Claudia Schipani
Keyword(s):  
Boundary Layer ◽  
Experimental Investigation ◽  
Reynolds Number ◽  
Separation Bubble ◽  
Suction Side ◽  
Low Pressure ◽  
Profile Measurement ◽  
High Lift ◽  
Low Pressure Turbine ◽  
Lower Reynolds Number

The paper presents the results of an experimental investigation of the wake shed from a high-lift low-pressure turbine profile. Measurement campaigns have been carried out in a three-blade large-scale turbine linear cascade. The Reynolds number based on the chord length has been varied in the range 100000–500000, to differentiate the influence of the boundary layer separation on the wake development. Two Reynolds number conditions, representative of the typical working conditions of a low pressure aeroengine turbine, have been more extensively investigated. Mean velocity and Reynolds stress components within the wake shed from the central blade have been measured across the wake by means of a two-component crossed miniature hotwire probe. The measuring traverses were located at distances ranging between 2 and 100% of the blade chord from the central blade trailing edge. Moreover, wake integral parameters, at the two Reynolds conditions, have been evaluated and compared. Both velocity and total pressure results show a wider wake occurring at the lower Reynolds number, due to the separation affecting the suction side boundary layer. Furthermore, the momentum thickness has been found to be much higher at the lower Reynolds number, due to the higher losses related to the separation bubble occurring on the blade suction side. The Strouhal number associated with the vortex shedding seems to be influenced by the Reynolds number, due to the different conditions of the suction side boundary layers.

scholarly journals Detailed Studies on Separated Boundary Layers Over Low-Pressure Turbine Airfoils Under Several High Lift Conditions: Effect of Freesteam Turbulence

2009 ◽  
Author(s):  
Ken-ichi Funazaki ◽  
Kazutoyo Yamada ◽  
Nozomi Tanaka ◽  
Yasuhiro Chiba
Keyword(s):  
Boundary Layer ◽  
Boundary Layers ◽  
Separation Bubble ◽  
Low Pressure ◽  
Scale Model ◽  
Freestream Turbulence ◽  
Suction Surface ◽  
High Lift ◽  
Low Pressure Turbine ◽  
Turbine Airfoils

This paper deals with experimental investigation on the interaction between inlet freestream turbulence and boundary layers with separation bubble on a low-pressure turbine airfoil under several High Lift conditions. Solidity of the cascade can be reduced by increasing the airfoil pitch by 25%, while maintaining the throat in the blade-to-blade passage. Reynolds number examined is 57000, based on chord length and averaged exit velocity. Freestream turbulence intensity at the inlet is varied from 0.80% (no grid condition) to 2.1% by use of turbulence grid. Hot-wire probe measurements of the boundary layer on the suction surface for Low Pressure (LP) turbines rotor are carried out to obtain time-averaged and time-resolved characteristics of the boundary layers under the influence of the freestream turbulence. Frequency analysis extracts some important features of the unsteady behaviors of the boundary layer, including vortex formation and shedding. Numerical analysis based on high resolution Large Eddy Simulation is also executed to enhance the understanding on the flow field around the highly loaded turbine airfoils. Standard Smagorinsky model is employed as subgrid scale model. Emphasis of the simulation is placed on the relationship of inherent instability of the shear layer of the separation bubble and the freestream turbulence.

The Effect of Pulsed Blowing on the Boundary Layer of a Highly Loaded Low Pressure Turbine Blade

2013 ◽  
Author(s):  
Marion Mack ◽  
Roland Brachmanski ◽  
Reinhard Niehuis
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Mach Number ◽  
Suction Side ◽  
Reynolds Numbers ◽  
Low Pressure ◽  
Trailing Edge ◽  
Low Pressure Turbine ◽  
Wide Range ◽  
Highly Loaded

The performance of the low pressure turbine (LPT) can vary appreciably, because this component operates under a wide range of Reynolds numbers. At higher Reynolds numbers, mid and aft loaded profiles have the advantage that transition of suction side boundary layer happens further downstream than at front loaded profiles, resulting in lower profile loss. At lower Reynolds numbers, aft loading of the blade can mean that if a suction side separation exists, it may remain open up to the trailing edge. This is especially the case when blade lift is increased via increased pitch to chord ratio. There is a trend in research towards exploring the effect of coupling boundary layer control with highly loaded turbine blades, in order to maximize performance over the full relevant Reynolds number range. In an earlier work, pulsed blowing with fluidic oscillators was shown to be effective in reducing the extent of the separated flow region and to significantly decrease the profile losses caused by separation over a wide range of Reynolds numbers. These experiments were carried out in the High-Speed Cascade Wind Tunnel of the German Federal Armed Forces University Munich, Germany, which allows to capture the effects of pulsed blowing at engine relevant conditions. The assumed control mechanism was the triggering of boundary layer transition by excitation of the Tollmien-Schlichting waves. The current work aims to gain further insight into the effects of pulsed blowing. It investigates the effect of a highly efficient configuration of pulsed blowing at a frequency of 9.5 kHz on the boundary layer at a Reynolds number of 70000 and exit Mach number of 0.6. The boundary layer profiles were measured at five positions between peak Mach number and the trailing edge with hot wire anemometry and pneumatic probes. Experiments were conducted with and without actuation under steady as well as periodically unsteady inflow conditions. The results show the development of the boundary layer and its interaction with incoming wakes. It is shown that pulsed blowing accelerates transition over the separation bubble and drastically reduces the boundary layer thickness.

Sign in / Sign up

Export Citation Format

Share Document