scholarly journals Management of High Speed Machinery Signatures to Meet Stealth Requirement in the Royal Swedish Navy Visby Class Corvette (YS 2000)

2001 ◽  
Author(s):  
Hans Liwång ◽  
Lars Pejlert ◽  
Steve Miller ◽  
Jan-Erik Gustavsson
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
High Speed ◽  
High Performance ◽  
Water Jet ◽  
Reduction Gear ◽  
Exhaust Pipe ◽  
Sandwich Construction ◽  
Main Work ◽  
Delay Detection

Over the years, the word stealth has been used more and more when discussing design and operational characteristics in military applications. New and more challenging techniques are constantly being applied to minimize signatures and thus hinder or delay detection and identification. The Visby Class Corvette is a multipurpose combat ship with 600 tons displacement. The hull is a sandwich construction of a PVC core with carbon fiber/vinyl laminate. The propulsion system consists of two identical CODOG machinery systems, each driving a KaMeWa 125 size Water Jet Unit. The Ship has special requirements for all signatures, i.e. Radar-, Hydro acoustics-, IR- and Magnetic Signature. The High Speed Machinery is twin Honeywell TF50A Gas Turbines, cantilever mounted side by side on the Main Reduction Gearbox housing. The Main Reduction Gearbox is a dual input high performance marine Gearbox designated MA - 107 SBS, designed and manufactured by Cincinnati Gear Co. The Low Speed Machinery is a MTU 16 V 2000 TE90 Diesel Engine connected to the MRG by a power take in shaft. Combustion Air for the Gas Turbines is ducted from the shipside Air Inlet Screen (radar screen) via 3-stage separating filters. The Exhausts from the twin Gas Turbines are combined into one Exhaust Pipe and ducted to the ship transom above the Water Jet stream. Very little can be changed in the Gas Turbine, but high quality such as well balanced rotating part contributes to reduce the signatures. However, the main work has to be accomplished by the building shipyard in cooperation with the Gas Turbine manufacturer. The Main Reduction Gearbox is more available for changes to reduce signatures, but even for the Gearbox the building shipyard has to take design and installation measures. The HSM installation consist mainly of the Gas Turbine Engine, the Main Reduction Gear, Water Jets Unit and surrounding equipment such as main shaft, bearings and so on. The emphasis in this paper is on the GT, MRG and their effect on some of the more well known signatures i.e. RCS, IR, Hydro acoustics and Magnetic. Also some design measures are discussed.

scholarly journals Gas Turbine Development in Sweden After 1945: A Historical Review

1998 ◽  
Author(s):  
Kjell T. E. Thoren
Keyword(s):  
Gas Turbine ◽  
Air Force ◽  
Gas Turbines ◽  
High Speed ◽  
High Performance ◽  
Historical Review ◽  
Propulsion Systems ◽  
Hybrid Propulsion ◽  
History Of ◽  
Industrial Gas Turbine

The gas turbine development history of Sweden is exciting. By international comparison Sweden and its gas turbine manufacturers are small but can nevertheless claim periods with the worlds highest output, or highest efficiency large industrial gas turbine respectively. Sweden has always created its own military aircraft and fitting, high performance engines are developed in Sweden in license cooperation with large international manufacturers. The Swedish Air Force ranked number four in the world during the 60s. Pioneering contributions were also made with small gas turbines, such as high speed turbogenerators in hybrid propulsion systems for cars and trucks. Professionals know that gas turbine development success does not come easy. A lot of setbacks have to be mastered. The size of the crew is not always significant in the process.

scholarly journals Gas Turbine Performance Enhancement for Naval Ship Propulsion using Wave Rotors

2019 ◽  
Author(s):  
A Fatsis ◽  
A S N Al Balushi
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
High Speed ◽  
High Performance ◽  
Performance Enhancement ◽  
Waste Heat ◽  
Specific Power ◽  
Inlet Temperature ◽  
Wave Rotor ◽  
Turbine Inlet

The propulsion demands of high speed naval vessels often rely on gas turbines fitted in small engine rooms, producing significant amounts of power achieving thus high performance requirements. Gas turbines can be used either to provide purely mechanical propulsion, or alternatively to generate electricity, which is subsequently used by electric drives to propel the ship. However, the thermal efficiencies of gas turbines are lower than those of Diesel engines of similar power, in addition to the fact that all gas turbines are less efficient as the ambient temperature rises, particularly for aero-derivative engines. In the context of improving the performance of existing marine gas turbines with minimum modifications to their baseline configuration, this article is proposing engine’s performance enhancement by integrating a pressure wave supercharger (or wave rotor), while keeping the compressor, combustion chamber and turbine entry temperature of the baseline engine unchanged. Thermodynamic cycle analysis for two-shaft gas turbine engines configurations with and without heat exchanger to recuperate the waste heat from the exhaust gases, typical for marine propulsion is performed for the baseline engines, as well as for the topped with four-port wave rotor engines, at design point conditions and their performances are compared accordingly. Important benefits are obtained for four-port wave rotor-topped engines in comparison to the self-standing baseline engines for the whole range of engine’s operation. It is found that the higher the turbine inlet temperature is, the more the benefit gain of the wave rotor topped engine is attained in terms of efficiency and specific power. It is also concluded that the integration of wave rotor particularly favours engines operating at low compressor pressure ratios and high turbine inlet temperatures. The effect of variation of the most important parameters on performance of the topped engine is investigated. It is concluded that wave rotor topping of marine gas turbines can lead to fuel savings and power increase.

Modern opportunities for preparation of ultra-pure water for feeding high-performance boiler plants

2020 ◽  
pp. 74-84
Author(s):  
A.A. Filimonova ◽  
◽  
N.D. Chichirova ◽  
A.A. Chichirov ◽  
A.A. Batalova ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
High Performance ◽  
Waste Heat ◽  
Pure Water ◽  
Combined Cycle ◽  
Feed Water ◽  
Operational Characteristics ◽  
Treatment Equipment

The article provides an overview of modern high-performance combined-cycle plants and gas turbine plants with waste heat boilers. The forecast for the introduction of gas turbine equipment at TPPs in the world and in Russia is presented. The classification of gas turbines according to the degree of energy efficiency and operational characteristics is given. Waste heat boilers are characterized in terms of design and associated performance and efficiency. To achieve high operating parameters of gas turbine and boiler equipment, it is necessary to use, among other things, modern water treatment equipment. The article discusses modern effective technologies, the leading place among which is occupied by membrane, and especially baromembrane methods of preparing feed water-waste heat boilers. At the same time, the ion exchange technology remains one of the most demanded at TPPs in the Russian Federation.

scholarly journals Progress in Novel Electrodeposited Bond Coats for Thermal Barrier Coating Systems

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4214
Author(s):  
Kranthi Kumar Maniam ◽  
Shiladitya Paul
Keyword(s):  
Gas Turbine ◽  
Thermal Barrier Coating ◽  
Gas Turbines ◽  
High Performance ◽  
Turbine Engines ◽  
Thermal Barrier ◽  
Gas Turbine Engines ◽  
Potential Cost ◽  
Bond Coats ◽  
Barrier Coating

The increased demand for high performance gas turbine engines has resulted in a continuous search for new base materials and coatings. With the significant developments in nickel-based superalloys, the quest for developments related to thermal barrier coating (TBC) systems is increasing rapidly and is considered a key area of research. Of key importance are the processing routes that can provide the required coating properties when applied on engine components with complex shapes, such as turbine vanes, blades, etc. Despite significant research and development in the coating systems, the scope of electrodeposition as a potential alternative to the conventional methods of producing bond coats has only been realised to a limited extent. Additionally, their effectiveness in prolonging the alloys’ lifetime is not well understood. This review summarises the work on electrodeposition as a coating development method for application in high temperature alloys for gas turbine engines and discusses the progress in the coatings that combine electrodeposition and other processes to achieve desired bond coats. The overall aim of this review is to emphasise the role of electrodeposition as a potential cost-effective alternative to produce bond coats. Besides, the developments in the electrodeposition of aluminium from ionic liquids for potential applications in gas turbines and the nuclear sector, as well as cost considerations and future challenges, are reviewed with the crucial raw materials’ current and future savings scenarios in mind.

Recent Advances in the Study of Film Cooling on the Gas Turbine Blade

2014 ◽  
Vol 971-973 ◽  
pp. 143-147 ◽  
Author(s):  
Ping Dai ◽  
Shuang Xiu Li
Keyword(s):  
Gas Turbine ◽  
Turbine Blade ◽  
Film Cooling ◽  
Gas Turbines ◽  
High Performance ◽  
Leading Edge ◽  
Development Trend ◽  
Research Progress ◽  
Gas Turbine Blade ◽  
New Generation

The development of a new generation of high performance gas turbine engines requires gas turbines to be operated at very high inlet temperatures, which are much higher than the allowable metal temperatures. Consequently, this necessitates the need for advanced cooling techniques. Among the numerous cooling technologies, the film cooling technology has superior advantages and relatively favorable application prospect. The recent research progress of film cooling techniques for gas turbine blade is reviewed and basic principle of film cooling is also illustrated. Progress on rotor blade and stationary blade of film cooling are introduced. Film cooling development of leading-edge was also generalized. Effect of various factor on cooling effectiveness and effect of the shape of the injection holes on plate film cooling are discussed. In addition, with respect to progress of discharge coefficient is presented. In the last, the future development trend and future investigation direction of film cooling are prospected.

scholarly journals Wall Temperature Measurements in Gas Turbine Combustors With Thermographic Phosphors

2018 ◽  
Vol 141 (4) ◽  
Author(s):  
Patrick Nau ◽  
Zhiyao Yin ◽  
Oliver Lammel ◽  
Wolfgang Meier
Keyword(s):  
Gas Turbine ◽  
Wall Temperature ◽  
Gas Turbines ◽  
High Speed ◽  
Bluff Body ◽  
Temperature Measurements ◽  
Transient Temperature ◽  
High Time Resolution ◽  
Ceramic Surface ◽  
Precessing Vortex Core

Phosphor thermometry has been developed for wall temperature measurements in gas turbines and gas turbine model combustors. An array of phosphors has been examined in detail for spatially and temporally resolved surface temperature measurements. Two examples are provided, one at high pressure (8 bar) and high temperature and one at atmospheric pressure with high time resolution. To study the feasibility of this technique for full-scale gas turbine applications, a high momentum confined jet combustor at 8 bar was used. Successful measurements up to 1700 K on a ceramic surface are shown with good accuracy. In the same combustor, temperatures on the combustor quartz walls were measured, which can be used as boundary conditions for numerical simulations. An atmospheric swirl-stabilized flame was used to study transient temperature changes on the bluff body. For this purpose, a high-speed setup (1 kHz) was used to measure the wall temperatures at an operating condition where the flame switches between being attached (M-flame) and being lifted (V-flame) (bistable). The influence of a precessing vortex core (PVC) present during M-flame periods is identified on the bluff body tip, but not at positions further inside the nozzle.

Boundary Layer Flashback Limits of Hydrogen-Methane-Air Flames in a Generic Swirl Burner at Gas Turbine Relevant Conditions

2020 ◽  
Author(s):  
Dominik Ebi ◽  
Peter Jansohn
Keyword(s):  
Boundary Layer ◽  
Gas Turbine ◽  
Wall Temperature ◽  
Gas Turbines ◽  
High Speed ◽  
Cooling System ◽  
Atmospheric Conditions ◽  
Preheat Temperature ◽  
Swirl Burner ◽  
Wide Range

Abstract Operating stationary gas turbines on hydrogen-rich fuels offers a pathway to significantly reduce greenhouse gas emissions in the power generation sector. A key challenge in the design of lean-premixed burners, which are flexible in terms of the amount of hydrogen in the fuel across a wide range and still adhere to the required emissions levels, is to prevent flame flashback. However, systematic investigations on flashback at gas turbine relevant conditions to support combustor development are sparse. The current work addresses the need for an improved understanding with an experimental study on boundary layer flashback in a generic swirl burner up to 7.5 bar and 300° C preheat temperature. Methane-hydrogen-air flames with 50 to 85% hydrogen by volume were investigated. High-speed imaging was applied to reveal the flame propagation pathway during flashback events. Flashback limits are reported in terms of the equivalence ratio for a given pressure, preheat temperature, bulk flow velocity and hydrogen content. The wall temperature of the center body along which the flame propagated during flashback events has been controlled by an oil heating/cooling system. This way, the effect any of the control parameters, e.g. pressure, had on the flashback limit was de-coupled from the otherwise inherently associated change in heat load on the wall and thus change in wall temperature. The results show that the preheat temperature has a weaker effect on the flashback propensity than expected. Increasing the pressure from atmospheric conditions to 2.5 bar strongly increases the flashback risk, but hardly affects the flashback limit beyond 2.5 bar.

The Effect of Transient Fuel Staging on Self-Excited Instabilities in a Multi-Nozzle Model Gas Turbine Combustor

2017 ◽  
Author(s):  
Wyatt Culler ◽  
Janith Samarasinghe ◽  
Bryan D. Quay ◽  
Domenic A. Santavicca ◽  
Jacqueline O’Connor
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
High Speed ◽  
Equivalence Ratio ◽  
Growth Time ◽  
Stable Operation ◽  
Time Constants ◽  
Decay Times ◽  
Fuel Staging ◽  
Passive Techniques

Combustion instability in gas turbines can be mitigated using active techniques or passive techniques, but passive techniques are almost exclusively used in industrial settings. While fuel staging, a common passive technique, is effective in reducing the amplitude of self-excited instabilities in gas turbine combustors at steady-state conditions, the effect of transients in fuel staging on self-excited instabilities is not well understood. This paper examines the effect of fuel staging transients on a laboratory-scale five-nozzle can combustor undergoing self-excited instabilities. The five nozzles are arranged in a four-around-one configuration and fuel staging is accomplished by increasing the center nozzle equivalence ratio. When the global equivalence ratio is φ = 0.70 and all nozzles are fueled equally, the combustor undergoes self-excited oscillations. These oscillations are suppressed when the center nozzle equivalence ratio is increased to φ = 0.80 or φ = 0.85. Two transient staging schedules are used, resulting in transitions from unstable to stable operation, and vice-versa. It is found that the characteristic instability decay times are dependent on the amount of fuel staging in the center nozzle. It is also found that the decay time constants differ from the growth time constants, indicating hysteresis in stability transition points. High speed CH* chemiluminescence images in combination with dynamic pressure measurements are used to determine the instantaneous phase difference between the heat release rate fluctuation and the combustor pressure fluctuation throughout the combustor. This analysis shows that the instability onset process is different from the instability decay process.

Future Vehicular Recuperator Technology Projections

1994 ◽  
Author(s):  
Robert A. Wilson ◽  
Daniel B. Kupratis ◽  
Satyanarayana Kodali
Keyword(s):  
Gas Turbine ◽  
Fuel Economy ◽  
Department Of Defense ◽  
Gas Turbines ◽  
High Performance ◽  
Development Program ◽  
Turn Of The Century ◽  
Turbine Engine ◽  
Technology Roadmap ◽  
Vehicle Propulsion

The Department of Defense and NASA have funded a major gas turbine development program, Integrated High Performance Turbine Engine Technology (IHPTET), to double the power density and fuel economy of gas turbines by the turn of the century. Seven major US gas turbine developers participated in this program. While the focus of IHPTET activity has been aircraft propulsion, the same underlying technology can be applied to water craft and terrestrial vehicle propulsion applications, such as the future main battle tank. For these applications, the gas turbines must be equipped with recuperators. Currently, there is no technology roadmap or set of goals to guide industry and government in the development of a next generation recuperator for such applications.

Investigation of Strip Seal Leakage With Special Focus on Seal Groove Design and Relative Displacement of Sealing Surfaces

2017 ◽  
Author(s):  
Thomas Huber ◽  
Cyrille Bricaud ◽  
Thomas Zierer
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
High Performance ◽  
Relative Displacement ◽  
Curvature Radius ◽  
Special Focus ◽  
Test Matrix ◽  
Seal Design ◽  
Geometric Relation ◽  
Geometric Deviation

Tight sealing lines are vital in large gas turbines (GT) to achieve high performance and efficiency. Leakage including rim purge air can sum up to 30% of the total cooling and leakage air consumption of a gas turbine. Leakage through static strip seals contributes about 1/3 to all leakage air. Considering the seal design as on drawings, sealing quality is generally influenced by the seal type, sealing groove curvature and the sealing groove roughness. In addition the sealing quality depends strongly on the geometric deviation of the groove compared to ideal design. This is caused by manufacturing deviations or relative movements of the grooves during operation of the parts containing the sealing. In the article at hand, different seal designs and pertinent sealing quality is discussed. More in detail, it is discussed the geometric relation of seal, groove and misalignment to predict the seal position relative to its groove confinements. The risk of seal clamping can be judged and adaptation of seal or groove geometry can be derived. The effect of leakage increase due to misalignment is investigated by a test matrix varying seal length and curvature radius of groove as well as radial misalignment.

Sign in / Sign up

Export Citation Format

Share Document