scholarly journals Binary Cycle Gas Fired Turbine for Gas Compression Service

1962 ◽  
Author(s):  
Adrian W. McAnneny
Keyword(s):  
Gas Turbine ◽  
Centrifugal Compressor ◽  
Gas Turbines ◽  
High Speed ◽  
Waste Heat ◽  
Low Cost ◽  
Main Line ◽  
Gas Compression ◽  
Binary Cycle ◽  
Additional Equipment

Three years ago a survey was made of the various prime movers available to the pipeline industry for gas compression. This survey included gas turbines and two and four-cycle reciprocating gas engines. The purpose of this study was to determine which of the existing equipments would be most economical and whether or not there was a need for the development of additional equipment. As a result of this economic study, it appeared there was a definite requirement in the industry for a high-speed, low-cost, gas turbine-centrifugal compressor unit for both field and main-line-station gas compression. As a result of the studies two gas-turbine-driven centrifugal compressor units were placed in operation early in 1960 at Cypress Station near Houston, waste-heat recovery systems being installed in the summer of 1961. Performance tests were satisfactory and subsequently six small gas-engine-driven compressor units have been installed at two main-line compressor stations.

Comparison of Operating Characteristics of a Two-Shaft Gas Turbine With a Single-Shaft Gas Turbine for Gas Line Pumping

1960 ◽  
Author(s):  
M. J. McDonough
Keyword(s):  
Gas Turbine ◽  
Fuel Consumption ◽  
Centrifugal Compressor ◽  
Gas Turbines ◽  
Low Cost ◽  
Prime Mover ◽  
Transportation Industry ◽  
Operating Characteristics ◽  
Shaft Unit ◽  
Discharge Pressure

Gas turbines are playing an important role in the ever-expanding gas-transportation industry. Coupled to a centrifugal compressor the gas turbine provides a low-cost, flexible prime mover for gas transmission. The two types of gas turbines most commonly used in this field are the single-shaft unit and the two-shaft unit. This paper describes and compares the operating characteristics of each unit along a typical centrifugal-compressor loading line for constant station discharge pressure. Horsepower-speed relationships and specific fuel consumption are considered in this comparison.

scholarly journals Gas Turbine Performance Enhancement for Naval Ship Propulsion using Wave Rotors

2019 ◽  
Author(s):  
A Fatsis ◽  
A S N Al Balushi
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
High Speed ◽  
High Performance ◽  
Performance Enhancement ◽  
Waste Heat ◽  
Specific Power ◽  
Inlet Temperature ◽  
Wave Rotor ◽  
Turbine Inlet

The propulsion demands of high speed naval vessels often rely on gas turbines fitted in small engine rooms, producing significant amounts of power achieving thus high performance requirements. Gas turbines can be used either to provide purely mechanical propulsion, or alternatively to generate electricity, which is subsequently used by electric drives to propel the ship. However, the thermal efficiencies of gas turbines are lower than those of Diesel engines of similar power, in addition to the fact that all gas turbines are less efficient as the ambient temperature rises, particularly for aero-derivative engines. In the context of improving the performance of existing marine gas turbines with minimum modifications to their baseline configuration, this article is proposing engine’s performance enhancement by integrating a pressure wave supercharger (or wave rotor), while keeping the compressor, combustion chamber and turbine entry temperature of the baseline engine unchanged. Thermodynamic cycle analysis for two-shaft gas turbine engines configurations with and without heat exchanger to recuperate the waste heat from the exhaust gases, typical for marine propulsion is performed for the baseline engines, as well as for the topped with four-port wave rotor engines, at design point conditions and their performances are compared accordingly. Important benefits are obtained for four-port wave rotor-topped engines in comparison to the self-standing baseline engines for the whole range of engine’s operation. It is found that the higher the turbine inlet temperature is, the more the benefit gain of the wave rotor topped engine is attained in terms of efficiency and specific power. It is also concluded that the integration of wave rotor particularly favours engines operating at low compressor pressure ratios and high turbine inlet temperatures. The effect of variation of the most important parameters on performance of the topped engine is investigated. It is concluded that wave rotor topping of marine gas turbines can lead to fuel savings and power increase.

Modern opportunities for preparation of ultra-pure water for feeding high-performance boiler plants

2020 ◽  
pp. 74-84
Author(s):  
A.A. Filimonova ◽  
◽  
N.D. Chichirova ◽  
A.A. Chichirov ◽  
A.A. Batalova ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
High Performance ◽  
Waste Heat ◽  
Pure Water ◽  
Combined Cycle ◽  
Feed Water ◽  
Operational Characteristics ◽  
Treatment Equipment

The article provides an overview of modern high-performance combined-cycle plants and gas turbine plants with waste heat boilers. The forecast for the introduction of gas turbine equipment at TPPs in the world and in Russia is presented. The classification of gas turbines according to the degree of energy efficiency and operational characteristics is given. Waste heat boilers are characterized in terms of design and associated performance and efficiency. To achieve high operating parameters of gas turbine and boiler equipment, it is necessary to use, among other things, modern water treatment equipment. The article discusses modern effective technologies, the leading place among which is occupied by membrane, and especially baromembrane methods of preparing feed water-waste heat boilers. At the same time, the ion exchange technology remains one of the most demanded at TPPs in the Russian Federation.

Design, Development and Application of Vehicle Gas Turbine Engines

1966 ◽  
Vol 181 (1) ◽  
pp. 149-172
Author(s):  
P. A. Phillips ◽  
Peter Spear
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Low Cost ◽  
Engine Performance ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Design Development ◽  
Turbine Engine ◽  
Wide Range ◽  
Cycle Temperature

After briefly summarizing worldwide automotive gas turbine activity, the paper analyses the power plant requirements of a wide range of vehicle applications in order to formulate the design criteria for acceptable vehicle gas turbines. Ample data are available on the thermodynamic merits of various gas turbine cycles; however, the low cost of its piston engine competitor tends to eliminate all but the simplest cycles from vehicle gas turbine considerations. In order to improve the part load fuel economy, some complexity is inevitable, but this is limited to the addition of a glass ceramic regenerator in the 150 b.h.p. engine which is described in some detail. The alternative further complications necessary to achieve satisfactory vehicle response at various power/weight ratios are examined. Further improvement in engine performance will come by increasing the maximum cycle temperature. This can be achieved at lower cost by the extension of the use of ceramics. The paper is intended to stimulate the design application of the gas turbine engine.

scholarly journals Wall Temperature Measurements in Gas Turbine Combustors With Thermographic Phosphors

2018 ◽  
Vol 141 (4) ◽  
Author(s):  
Patrick Nau ◽  
Zhiyao Yin ◽  
Oliver Lammel ◽  
Wolfgang Meier
Keyword(s):  
Gas Turbine ◽  
Wall Temperature ◽  
Gas Turbines ◽  
High Speed ◽  
Bluff Body ◽  
Temperature Measurements ◽  
Transient Temperature ◽  
High Time Resolution ◽  
Ceramic Surface ◽  
Precessing Vortex Core

Phosphor thermometry has been developed for wall temperature measurements in gas turbines and gas turbine model combustors. An array of phosphors has been examined in detail for spatially and temporally resolved surface temperature measurements. Two examples are provided, one at high pressure (8 bar) and high temperature and one at atmospheric pressure with high time resolution. To study the feasibility of this technique for full-scale gas turbine applications, a high momentum confined jet combustor at 8 bar was used. Successful measurements up to 1700 K on a ceramic surface are shown with good accuracy. In the same combustor, temperatures on the combustor quartz walls were measured, which can be used as boundary conditions for numerical simulations. An atmospheric swirl-stabilized flame was used to study transient temperature changes on the bluff body. For this purpose, a high-speed setup (1 kHz) was used to measure the wall temperatures at an operating condition where the flame switches between being attached (M-flame) and being lifted (V-flame) (bistable). The influence of a precessing vortex core (PVC) present during M-flame periods is identified on the bluff body tip, but not at positions further inside the nozzle.

scholarly journals Gas Turbine Health State Determination: Methodology Approach and Field Application

2012 ◽  
Vol 2012 ◽  
pp. 1-14 ◽  
Author(s):  
Michele Pinelli ◽  
Pier Ruggero Spina ◽  
Mauro Venturini
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Field Measurements ◽  
Field Application ◽  
Diagnostic Process ◽  
Health State ◽  
Gas Compression ◽  
State Determination ◽  
Measurement Validation ◽  
Machine Health

A reduction of gas turbine maintenance costs, together with the increase in machine availability and the reduction of management costs, is usually expected when gas turbine preventive maintenance is performed in parallel to on-condition maintenance. However, on-condition maintenance requires up-to-date knowledge of the machine health state. The gas turbine health state can be determined by means of Gas Path Analysis (GPA) techniques, which allow the calculation of machine health state indices, starting from measurements taken on the machine. Since the GPA technique makes use of field measurements, the reliability of the diagnostic process also depends on measurement reliability. In this paper, a comprehensive approach for both the measurement validation and health state determination of gas turbines is discussed, and its application to a 5 MW gas turbine working in a natural gas compression plant is presented.

Boundary Layer Flashback Limits of Hydrogen-Methane-Air Flames in a Generic Swirl Burner at Gas Turbine Relevant Conditions

2020 ◽  
Author(s):  
Dominik Ebi ◽  
Peter Jansohn
Keyword(s):  
Boundary Layer ◽  
Gas Turbine ◽  
Wall Temperature ◽  
Gas Turbines ◽  
High Speed ◽  
Cooling System ◽  
Atmospheric Conditions ◽  
Preheat Temperature ◽  
Swirl Burner ◽  
Wide Range

Abstract Operating stationary gas turbines on hydrogen-rich fuels offers a pathway to significantly reduce greenhouse gas emissions in the power generation sector. A key challenge in the design of lean-premixed burners, which are flexible in terms of the amount of hydrogen in the fuel across a wide range and still adhere to the required emissions levels, is to prevent flame flashback. However, systematic investigations on flashback at gas turbine relevant conditions to support combustor development are sparse. The current work addresses the need for an improved understanding with an experimental study on boundary layer flashback in a generic swirl burner up to 7.5 bar and 300° C preheat temperature. Methane-hydrogen-air flames with 50 to 85% hydrogen by volume were investigated. High-speed imaging was applied to reveal the flame propagation pathway during flashback events. Flashback limits are reported in terms of the equivalence ratio for a given pressure, preheat temperature, bulk flow velocity and hydrogen content. The wall temperature of the center body along which the flame propagated during flashback events has been controlled by an oil heating/cooling system. This way, the effect any of the control parameters, e.g. pressure, had on the flashback limit was de-coupled from the otherwise inherently associated change in heat load on the wall and thus change in wall temperature. The results show that the preheat temperature has a weaker effect on the flashback propensity than expected. Increasing the pressure from atmospheric conditions to 2.5 bar strongly increases the flashback risk, but hardly affects the flashback limit beyond 2.5 bar.

The Effect of Transient Fuel Staging on Self-Excited Instabilities in a Multi-Nozzle Model Gas Turbine Combustor

2017 ◽  
Author(s):  
Wyatt Culler ◽  
Janith Samarasinghe ◽  
Bryan D. Quay ◽  
Domenic A. Santavicca ◽  
Jacqueline O’Connor
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
High Speed ◽  
Equivalence Ratio ◽  
Growth Time ◽  
Stable Operation ◽  
Time Constants ◽  
Decay Times ◽  
Fuel Staging ◽  
Passive Techniques

Combustion instability in gas turbines can be mitigated using active techniques or passive techniques, but passive techniques are almost exclusively used in industrial settings. While fuel staging, a common passive technique, is effective in reducing the amplitude of self-excited instabilities in gas turbine combustors at steady-state conditions, the effect of transients in fuel staging on self-excited instabilities is not well understood. This paper examines the effect of fuel staging transients on a laboratory-scale five-nozzle can combustor undergoing self-excited instabilities. The five nozzles are arranged in a four-around-one configuration and fuel staging is accomplished by increasing the center nozzle equivalence ratio. When the global equivalence ratio is φ = 0.70 and all nozzles are fueled equally, the combustor undergoes self-excited oscillations. These oscillations are suppressed when the center nozzle equivalence ratio is increased to φ = 0.80 or φ = 0.85. Two transient staging schedules are used, resulting in transitions from unstable to stable operation, and vice-versa. It is found that the characteristic instability decay times are dependent on the amount of fuel staging in the center nozzle. It is also found that the decay time constants differ from the growth time constants, indicating hysteresis in stability transition points. High speed CH* chemiluminescence images in combination with dynamic pressure measurements are used to determine the instantaneous phase difference between the heat release rate fluctuation and the combustor pressure fluctuation throughout the combustor. This analysis shows that the instability onset process is different from the instability decay process.

Arrangement and Optimisation Turbocompressors in an Off-Shore Natural Gas Extraction Station

2005 ◽  
Author(s):  
M. Pinelli ◽  
A. Mazzi ◽  
G. Russo
Keyword(s):  
Centrifugal Compressor ◽  
Gas Turbines ◽  
Optimization Procedure ◽  
Thermodynamic Cycle ◽  
Actual Operating ◽  
Gas Compression ◽  
Consequent Reduction ◽  
Suitable Arrangement ◽  
High Production ◽  
Definition Of

In this paper, a methodology for the optimization of a single off-shore gas compression station is developed. The station is composed of three gas turbines, each one driving a centrifugal compressor. The study concerns the feasibility of the most suitable arrangement to face the depletion of wells and the consequent reduction of the head top pressure. Once the arrangement is chosen, an optimization procedure is developed and carried out. The procedure, which is aimed at obtaining either high production rates or good station efficiency, is based on knowledge of the centrifugal compressor characteristics and on the availability of gas turbine thermodynamic cycle program, the latter allowing the definition of the machine actual operating state.

scholarly journals Thermodynamic modelling and efficiency analysis of a class of real indirectly fired gas turbine cycles

2009 ◽  
Vol 13 (4) ◽  
pp. 41-48
Author(s):  
Zheshu Ma ◽  
Zhenhuan Zhu
Keyword(s):  
High Temperature ◽  
Heat Exchanger ◽  
Gas Turbine ◽  
Power Output ◽  
Gas Turbines ◽  
Waste Heat ◽  
Operational Parameters ◽  
Forecast Performance ◽  
Micro Gas Turbine ◽  
Temperature Heat

Indirectly or externally-fired gas-turbines (IFGT or EFGT) are novel technology under development for small and medium scale combined power and heat supplies in combination with micro gas turbine technologies mainly for the utilization of the waste heat from the turbine in a recuperative process and the possibility of burning biomass or 'dirty' fuel by employing a high temperature heat exchanger to avoid the combustion gases passing through the turbine. In this paper, by assuming that all fluid friction losses in the compressor and turbine are quantified by a corresponding isentropic efficiency and all global irreversibilities in the high temperature heat exchanger are taken into account by an effective efficiency, a one dimensional model including power output and cycle efficiency formulation is derived for a class of real IFGT cycles. To illustrate and analyze the effect of operational parameters on IFGT efficiency, detailed numerical analysis and figures are produced. The results summarized by figures show that IFGT cycles are most efficient under low compression ratio ranges (3.0-6.0) and fit for low power output circumstances integrating with micro gas turbine technology. The model derived can be used to analyze and forecast performance of real IFGT configurations.

Sign in / Sign up

Export Citation Format

Share Document