Effect of Waviness on Vibration and Acoustic Features of Rolling Element Bearing

2012 ◽  
Author(s):  
Yimin Shao ◽  
Pei Wang ◽  
Zaigang Chen
Keyword(s):  
Dynamic Model ◽  
Computational Cost ◽  
Element Model ◽  
Mapping Method ◽  
Rolling Element Bearing ◽  
Acoustic Features ◽  
Rigid Displacement ◽  
Outer Race ◽  
Deep Groove ◽  
Rolling Element

Waviness of rolling element bearings, as one of the most concerned factors, would greatly influence the dynamic and acoustic performances of machines. In this paper, a new algorithm of vibro-acoustic coupling, which is based on the displacement mapping method by applying the displacement history obtained from a 6-DOF bearing dynamic model to be as the boundary condition of the finite element model of the bearing housing, is developed to predict the effect of waviness on the vibration and acoustic features of the bearing. The displacement excitation of the circumferential surface of bearing housing can be obtained by vector synthesis of bearing rigid displacement from the 6-DOF bearing dynamic model. This new method enables not only the reduction in computational cost, but also simulation of the bearing waviness under different sizes. A 6308 deep groove ball bearing model with outer race waviness is taken as an example case to examine the effectiveness of the new algorithm. The simulation results show that the new algorithm is able to predict the vibration and acoustic features of the bearing with waviness.

A New Vibration of Rolling Element Bearing With Localized Defect Considering the Impact Force

2015 ◽  
Author(s):  
Wentao Huang ◽  
Zhenzhen Dong ◽  
Fanchao Kong ◽  
Qiang Fu
Keyword(s):  
Impact Force ◽  
Structural Parameters ◽  
Rolling Element Bearing ◽  
Mechanism Analysis ◽  
Outer Race ◽  
Contact Areas ◽  
Deep Groove ◽  
Rolling Element ◽  
Rolling Elements ◽  
The Impact

In this paper, a vibration model considering the impact force is developed based on Hertz contact theory. The model considered both structural parameters and kinematic parameters. In this model, the contact areas between balls and races are simulated as linear springs, and the contact areas between the inner race and shaft and the contact areas between the outer race and housing are considered as spring-damper systems. Unlike previous studies, in which the stiffness was simply calculated in one direction, the stiffness parameters were calculated separately in the horizontal and vertical directions in the present study. In this model, the impact process between rolling elements and defective races, which is affected by velocity, was studied in detail. The solution of the vibration equation was obtained using the Runge-Kutta method. The numerical results for 6204 deep groove type ball bearings with outer race defects have been obtained and compared with the experimental results, which validated the effectiveness of this model in both the fault mechanism analysis of rolling element bearings and fault diagnosis.

An Enhanced Study of the Load–Displacement Relationships for Rolling Element Bearings

2013 ◽  
Vol 136 (1) ◽  
Author(s):  
L. Houpert
Keyword(s):  
Contact Angle ◽  
Roller Bearing ◽  
Rolling Element Bearing ◽  
Smooth Transition ◽  
Ball Bearings ◽  
Element Analysis ◽  
Outer Race ◽  
Deep Groove ◽  
Rolling Element ◽  
Element Bearing

An enhanced analytical approach is suggested for calculating three rolling element bearing loads Fx, Fy, and Fz as well as the two tilting moments My and Mz as a function of five relative race displacements: three translations dx, dy, and dz, and two tilting angles dθy and dθz. A full coupling between all these displacements and forces is considered. This approach is particularly recommended for programming the rolling element bearing behavior in any finite element analysis or multibody system dynamic tool, since only two nodes are considered: one for the inner race center, usually connected to a shaft, and another node for the outer race center, connected to the housing. Also, roller and raceway crown radii are considered, meaning that Hertzian point contacts stiffness can be used at low load with a smooth transition toward Hertzian line contact as the load increases. This approach can be used for describing any rolling element bearing type when neglecting centrifugal and gyroscopic effects and applying the approximation of a constant ball–race contact angle. Deep groove ball bearings (whose contact angle sign follows the sign of the applied bearing axial force) or other ball bearings or spherical roller bearing operating under large misalignment may not support such approximations.

The Dynamic Behavior of a Rolling Element Auxiliary Bearing Following Rotor Impact

2001 ◽  
Vol 124 (2) ◽  
pp. 406-413 ◽  
Author(s):  
M. O. T. Cole ◽  
P. S. Keogh ◽  
C. R. Burrows
Keyword(s):  
Dynamic Behavior ◽  
Angular Acceleration ◽  
Element Model ◽  
Magnetic Bearing ◽  
Rolling Element Bearing ◽  
Linear Matrix ◽  
Rolling Element ◽  
Non Linear ◽  
In Series ◽  
Inner Race

The dynamic behavior of a rolling element bearing under auxiliary operation in rotor/magnetic bearing systems is analyzed. When contact with the rotor occurs, the inner race experiences high impact forces and rapid angular acceleration. A finite element model is used to account for flexibility of the inner race in series with non-linear ball stiffnesses arising from the ball-race contact zones. The dynamic conditions during rotor/inner race contact, including ball/race creep, are deduced from a non-linear matrix equation. The influences of bearing parameters are considered together with implications for energy dissipation in the bearing.

scholarly journals Estimation of the Defect Width on the Outer Race of a Rolling Element Bearing under Time-Varying Speed Conditions

2019 ◽  
Vol 2019 ◽  
pp. 1-11 ◽  
Author(s):  
Guang-Quan Hou ◽  
Chang-Myung Lee
Keyword(s):  
Research Work ◽  
Defect Size ◽  
Remaining Useful Life ◽  
Rolling Element Bearing ◽  
Time Varying ◽  
Entry And Exit ◽  
Outer Race ◽  
Time Frequency ◽  
Rolling Element ◽  
Element Bearing

Fault diagnosis and failure prognostics for rolling element bearing are helpful for preventing equipment failure and predicting the remaining useful life (RUL) to avoid catastrophic failure. Spall size is an important fault feature for RUL prediction, and most research work has focused on estimating the fault size under constant speed conditions. However, estimation of the defect width under time-varying speed conditions is still a challenge. In this paper, a method is proposed to solve this problem. To enhance the entry and exit events, the edited cepstrum is used to remove the determined components. The preprocessed signal is resampled from the time domain to the angular domain to eliminate the effect of speed variation and measure the defect size of a rolling element bearing on outer race. Next, the transient impulse components are extracted by local mean decomposition. The entry and exit points when the roller passes over the defect width on the outer race were identified by further processing the extracted signal with time-frequency analysis based on the continuous wavelet transform. The defect size can be calculated with the angle duration, which is measured from the identified entry and exit points. The proposed method was validated experimentally.

scholarly journals Effects of Ultra-Clean and Centrifugal Filtration on Rolling-Element Bearing Life

1982 ◽  
Vol 104 (3) ◽  
pp. 283-291 ◽  
Author(s):  
S. H. Loewenthal ◽  
D. W. Moyer ◽  
W. M. Needelman
Keyword(s):  
Aircraft Engine ◽  
Surface Damage ◽  
Fatigue Tests ◽  
Rolling Element Bearing ◽  
Bearing Life ◽  
Deep Groove ◽  
Rolling Element ◽  
Element Bearing ◽  
High Level ◽  
Better Than

Fatigue tests were conducted on groups of 65-millimeter bore diameter deep-groove ball bearings in a MIL-L-23699 lubricant under two levels of filtration. In one test series, the oil cleanliness was maintained at an exceptionally high level (better than a class of “00” per NAS 1638) with a 3 micron absolute barrier filter. These tests were intended to determine the “upper limit” in bearing life under the strictest possible lubricant cleanliness conditions. In the tests using a centrifugal oil filter, contaminants of the type found in aircraft engine filters were injected into the filters’ supply line at 125 milligrams per bearing-hour. “Ultra-clean” lubrication produced bearing fatigue lives that were approximately twice that obtained in previous tests with contaminated oil using 3 micron absolute filtration and approximately three times that obtained with 49 micron filtration. It was also observed that the centrifugal oil filter had approximately the same effectiveness as a 30 micron absolute filter in preventing bearing surface damage.

Advanced Rolling-Element Bearing Diagnostics Based on Cyclic Spectral Analysis

2007 ◽  
Vol 347 ◽  
pp. 265-270
Author(s):  
Jerome Antoni ◽  
Roger Boustany
Keyword(s):  
Background Noise ◽  
Rolling Element Bearing ◽  
Outer Race ◽  
Spectral Signatures ◽  
Bearing Diagnostics ◽  
Rolling Element ◽  
Cyclical Behaviour ◽  
Element Bearing ◽  
Incipient Fault ◽  
Inner Race

Rolling-element bearing vibrations are random cyclostationary, that is they exhibit a cyclical behaviour of their statistical properties while the machine is operating. This property is so symptomatic when an incipient fault develops that it can be efficiently exploited for diagnostics. This paper gives a synthetic but comprehensive discussion about this issue. First, the cyclostationarity of bearing signals is proved from a simple phenomenological model. Once this property is established, the question is then addressed of which spectral quantity can adequately characterise such vibration signals. In this respect, the cyclic coherence - and its multi-dimensional extension in the case of multi-sensors measurements -- is shown to be twice optimal: first to evidence the presence of a fault in high levels of background noise, and second to return a relative measure of its severity. These advantages make it an appealing candidate to be used in adverse industrial environments. The use and interpretation of the proposed tool are then illustrated on actual industrial measurements, and a special attention is paid to describe the typical "cyclic spectral signatures" of inner race, outer race, and rolling-element faults.

New Feature Extraction Method for the Detection of Defects in Rolling Element Bearings

2012 ◽  
Vol 134 (8) ◽  
Author(s):  
Ling Xiang ◽  
Aijun Hu
Keyword(s):  
Ensemble Empirical Mode Decomposition ◽  
Rolling Element Bearing ◽  
Rolling Element Bearings ◽  
Intrinsic Mode Functions ◽  
Feature Extraction Method ◽  
Outer Race ◽  
Mode Decomposition ◽  
Rolling Element ◽  
Envelope Spectrum ◽  
Detection Of Defects

This paper proposes a new method based on ensemble empirical mode decomposition (EEMD) and kurtosis criterion for the detection of defects in rolling element bearings. Some intrinsic mode functions (IMFs) are presented to obtain symptom wave by EEMD. The different kurtosis of the intrinsic mode function is determined to select the envelope spectrum. The fault feature based on the IMF envelope spectrum whose kurtosis is the maximum is extracted, and fault patterns of roller bearings can be effectively differentiated. Practical examples of diagnosis for a rolling element bearing are provided to verify the effectiveness of the proposed method. The verification results show that the bearing faults that typically occur in rolling element bearings, such as outer-race and inner-race, can be effectively identified by the proposed method.

Transient Rotordynamic Modeling of Rolling Element Bearing Systems

2001 ◽  
Author(s):  
A. Liew ◽  
N. S. Feng ◽  
E. J. Hahn
Keyword(s):  
Rolling Element Bearing ◽  
Hertzian Contact ◽  
Centrifugal Load ◽  
Linear Behavior ◽  
Deep Groove ◽  
Rolling Element ◽  
Rolling Elements ◽  
Load Effects ◽  
Element Bearing ◽  
Bearing Preload

Non-linearity effects in rolling element bearings may arise from the Hertzian contact force deformation relationship, the presence of clearance between the rolling elements and the bearing races, and the bearing to housing clearance. Assuming zero bearing to housing clearance and ignoring rolling element centrifugal load effects, it has been shown in earlier work that Rotor Bearing Systems (RBSs) with deep groove ball bearings can give rise to non-linear behavior such as chaotic motion and jump. This paper extends the bearing model to include rolling element centrifugal load, angular contacts and axial dynamics. The effect of more sophisticated bearing models is illustrated in both a rigidly supported rigid RBS and a flexibly supported flexible RBS, the latter being a model of a test rig designed to simulate an aircraft mounted accessory drive unit. Results are presented on the effect of bearing preload on the unbalance response up to a speed of 18,000 rpm.

scholarly journals Analytical model and spectral characteristics of acoustic emission signal produced by localized fault of rolling element bearing

2021 ◽  
Vol 39 (4) ◽  
pp. 831-838
Author(s):  
Fazhong Li ◽  
Zengshui He ◽  
Lin Zhang ◽  
Anbo Ming ◽  
Yongsheng Yang
Keyword(s):  
Acoustic Emission ◽  
Analytical Model ◽  
High Frequency ◽  
Spectral Characteristics ◽  
Rolling Element Bearing ◽  
Outer Race ◽  
Emission Signal ◽  
Rolling Element ◽  
Excitation Mechanisms ◽  
Element Bearing

The accurate description of acoustic emission signals produced by the localized fault of a rolling element bearing plays an important role in its feature extraction and analysis. This paper analyzes the excitation mechanisms and develops the analytical model of acoustic emission signals produced when the rolling element bearing passes across the localized fault on the inner or outer race. Based on the analytical model, the spectral characteristics are discussed substantially. Simulations and experiments are carried out to validate the efficacy of the model developed in the paper. The experimental results show that the response signal thus produced has two parts. The first one is produced by the entry of the rolling element bearing, while the other is produced by the departure of the rolling element bearing. The energy of both parts is concentrated around the resonance frequency of the acoustic emission transducer. Generally, the interval of adjacent acoustic emission events is not equivalent to each other and the corresponding spectrum is continuous in the high frequency band.

Sign in / Sign up

Export Citation Format

Share Document