scholarly journals Research on the experimental performance of gas-fired boiler based on the total heat recovery technology of absorption heat pump

2021 ◽  
Vol 261 ◽  
pp. 01059
Author(s):  
Xujing Zhai ◽  
Shoutao Tian ◽  
Kelin Zhu ◽  
Pan Huang ◽  
Jin Yu ◽  
...  
Keyword(s):  
Energy Saving ◽  
Heat Pump ◽  
Thermal Efficiency ◽  
Heat Recovery ◽  
Gas Flow ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Absorption Heat Pump ◽  
Reconstruction Project ◽  
Exhaust Gas Temperature

Based on an example of a gas-fired boiler for an industrial user in Tianjin, the absorption heat pump technology was used to carry out energy-saving transformation of the above boiler. The actual test was carried out on the gas flow, exhaust gas temperature and other parameters from January 2, 2018 to February 26, 2018. And then, the thermal efficiency of the boiler was analysed. The results show that after the energy-saving transformation, the exhaust gas temperature of the gas-fired boiler can be reduced from 140 °C to about 40 °C, and the overall thermal efficiency of the boiler also rises from 89.5% to 101.3%, which is 13.2% higher than that before optimization. According to the economic analysis, the energy-saving reconstruction project can achieve an energy-saving economic benefit of 1.598 million yuan throughout the year, with obvious energy-saving and emission reduction benefits.

Assessment of a Syngas-Diesel Dual Fuelled Compression Ignition Engine

2010 ◽  
Author(s):  
Bibhuti B. Sahoo ◽  
Niranjan Sahoo ◽  
Ujjwal K. Saha
Keyword(s):  
Diesel Engine ◽  
Thermal Efficiency ◽  
Gas Flow ◽  
Direct Injection ◽  
Dual Fuel ◽  
Exhaust Gas ◽  
Compression Ignition ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Exhaust Gas Temperature

Synthesis gas (Syngas), a mixture of hydrogen and carbon monoxide, can be manufactured from natural gas, coal, petroleum, biomass, and even from organic wastes. It can substitute fossil diesel as an alternative gaseous fuel in compression ignition engines under dual fuel operation route. Experiments were conducted in a single cylinder, constant speed and direct injection diesel engine fuelled with syngas-diesel in dual fuel mode. The engine is designed to develop a power output of 5.2 kW at its rated speed of 1500 rpm under variable loads with inducted syngas fuel having H2 to CO ratio of 1:1 by volume. Diesel fuel as a pilot was injected into the engine in the conventional manner. The diesel engine was run at varying loads of 20, 40, 60, 80 and 100%. The performance of dual fuel engine is assessed by parameters such as thermal efficiency, exhaust gas temperature, diesel replacement rate, gas flow rate, peak cylinder pressure, exhaust O2 and emissions like NOx, CO and HC. Dual fuel operation showed a decrease in brake thermal efficiency from 16.1% to a maximum of 20.92% at 80% load. The maximum diesel substitution by syngas was found 58.77% at minimum exhaust O2 availability condition of 80% engine load. The NOx level was reduced from 144 ppm to 103 ppm for syngas-diesel mode at the best efficiency point. Due to poor combustion efficiency of dual fuel operation, there were increases in CO and HC emissions throughout the range of engine test loads. The decrease in peak pressure causes the exhaust gas temperature to rise at all loads of dual fuel operation. The present investigation provides some useful indications of using syngas fuel in a diesel engine under dual fuel operation.

scholarly journals Experimental Study on Operation Regulation of a Coupled High–Low Energy Flue Gas Waste Heat Recovery System Based on Exhaust Gas Temperature Control

Energies ◽  
2019 ◽  
Vol 12 (4) ◽  
pp. 706 ◽  
Author(s):  
Jiayou Liu ◽  
Fengzhong Sun
Keyword(s):  
Flue Gas ◽  
Heat Recovery ◽  
Waste Heat Recovery ◽  
Gas Flow ◽  
Waste Heat ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Waste Heat Recovery System ◽  
Recovery System ◽  
Exhaust Gas Temperature

Controlling the exhaust gas temperature (EGT) of coal–fired boilers at a reasonable value is beneficial to ensuring unit efficiency and preventing acid corrosion and fouling of tail heating surfaces in power plants. To obtain the operation regulation of coupled high–low energy flue gas waste heat recovery system (CWHRS) under a given EGT, experimental equipment was designed and built. Experiments were carried out to maintain the exhaust gas temperature under different flue gas flow, flue gas temperature and air temperature conditions. As the flue gas flows, the flue gas temperatures and air temperatures increased, and the bypass flue gas flow proportions or the water flows of the additional economizer were increased to maintain the EGT at about 85 °C. An improved low temperature economizer (LTE) and front located air heater (FAH) system were put forward. As the flow of the crossover pipe increased, the EGT and the inlet water temperature of the LTE increased. As the flow of the circulating loop increased, the EGT and the inlet water temperature of the LTE decreased. Operation regulations of LTE–FAH system under four cases were given. The operation regulations of CWHRS and LTE–FAH system can provide references for power plant operation.

Energetic Based Organic Fluid Selection for a Solid Oxide Fuel Cell-Organic Rankine Cycle Combined System

2012 ◽  
Vol 622-623 ◽  
pp. 1162-1167
Author(s):  
Han Fei Tuo
Keyword(s):  
Fuel Cell ◽  
Solid Oxide Fuel Cell ◽  
Heat Recovery ◽  
Waste Heat ◽  
Solid Oxide ◽  
Exhaust Gas ◽  
Oxide Fuel ◽  
Gas Temperature ◽  
Selection For ◽  
Exhaust Gas Temperature

In this study, energetic based fluid selection for a solid oxide fuel cell-organic rankine combined power system is investigated. 9 dry organic fluids with varied critical temperatures are chosen and their corresponding ORC cycle performances are evaluated at different turbine inlet temperatures and exhaust gas temperature (waste heat source) from the upper cycle. It is found that actual ORC cycle efficiency for each fluid strongly depends on the waste heat recovery performance of the heat recovery vapor generator. Exhaust gas temperature determines the optimal fluid which yields the highest efficiency.

scholarly journals Thermodynamic Investigation of an Integrated Solar Combined Cycle with an ORC System

Entropy ◽  
2019 ◽  
Vol 21 (4) ◽  
pp. 428 ◽  
Author(s):  
Wang ◽  
Fu
Keyword(s):  
Solar Radiation ◽  
Thermal Efficiency ◽  
Unit Cost ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Exergy Efficiency ◽  
Combined Cycle ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Exhaust Gas Temperature

An integrated solar combined cycle (ISCC) with a low temperature waste heat recovery system is proposed in this paper. The combined system consists of a conventional natural gas combined cycle, organic Rankine cycle and solar fields. The performance of an organic Rankine cycle subsystem as well as the overall proposed ISCC system are analyzed using organic working fluids. Besides, parameters including the pump discharge pressure, exhaust gas temperature, thermal and exergy efficiencies, unit cost of exergy for product and annual CO2-savings were considered. Results indicate that Rc318 contributes the highest exhaust gas temperature of 71.2℃, while R113 showed the lowest exhaust gas temperature of 65.89 at 800 W/m2, in the proposed ISCC system. The overall plant thermal efficiency increases rapidly with solar radiation, while the exergy efficiency appears to have a downward trend. R227ea had both the largest thermal efficiency of 58.33% and exergy efficiency of 48.09% at 800W/m2. In addition, for the organic Rankine cycle, the exergy destructions of the evaporator, turbine and condenser decreased with increasing solar radiation. The evaporator contributed the largest exergy destruction followed by the turbine, condenser and pump. Besides, according to the economic analysis, R227ea had the lowest production cost of 19.3 $/GJ.

scholarly journals A review of heat recovery possibility in flue gases discharge system of gas radiant heaters

2019 ◽  
Vol 116 ◽  
pp. 00017 ◽  
Author(s):  
Edyta Dudkiewicz ◽  
Paweł Szałański
Keyword(s):  
Heat Recovery ◽  
Heating System ◽  
Flue Gases ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Discharge System ◽  
Common Solution ◽  
Recovery System ◽  
Exhaust Gas Temperature ◽  
Heat Energy Recovery

Heating of large-cubage buildings accounts for significant share of energy consumption. The radiant heating system using gas heaters is a common solution for large-cubage halls and is considered to be energy efficient. There is a possibility of additional heat energy recovery from the flue gases of gas radiant heaters because new solutions were introduced to the market. Furthermore heat recovery consists the most promising solution and develop during the recent years rapidly. On the other hand, few works have been dedicated to heat recovery from exhaust gas but none of them consider exhaust gas from radiant heaters. Exhaust gas temperature depends on the type and efficiency of the gas heater. The selection of both the type of radiant heaters and the heat recovery system requires many factors to be taken into account. This study consider possibilities for application of different heat exchangers in exhaust gases system of gas radiant heaters. The authors propose to classify exhaust gas heat recovery systems in dependence on intermediary medium: water/air, gas heaters type: ceramic/tube and number (single/group) and their mounting location.

Impact of Oxygenated Additives on Performance Characteristics of Methyl Ester in IC Engine

2016 ◽  
Vol 852 ◽  
pp. 724-728 ◽  
Author(s):  
D. Yuvarajan ◽  
K. Pradeep ◽  
S. Magesh Kumar
Keyword(s):  
Thermal Efficiency ◽  
Butyl Alcohol ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Ic Engine ◽  
Oxygenated Additives ◽  
Lower Viscosity ◽  
Exhaust Gas Temperature ◽  
The Impact

In this present work, the impact of blending n-butyl alcohol, a next generation biofuel with jatropha biodiesel on the performance of a diesel engine are examined. Tests were performed on a constant speed compression ignition engine using n-butyl alcohol / jatropha biodiesel blends. N-butyl alcohol was added to jatropha biodiesel by 10, 20 and 30% by volume. Performance parameters namely break thermal efficiency (BTE), Brake specific fuel consumption (BSFC) and Exhaust gas temperature (EGT) were analyzed in this work. It was experimentally found that by adding n-butyl alcohol to neat jatropha biodiesel, significant reduction in viscosity was observed. In addition, break thermal efficiency was increased by 0.8 % due to improved atomization of the blends. Further, brake specific fuel and exhaust gas temperature was further reduced due to lower viscosity and improved combustion rate with addition of n-butyl alcohol to jatropha biodiesel.

scholarly journals An Experimental Study on the Performance Characteristics of a Diesel Engine Fueled with ULSD-Biodiesel Blends

2020 ◽  
Vol 10 (2) ◽  
pp. 183-190
Author(s):  
Viet Dung Tran ◽  
Anh Tuan Le ◽  
Anh Tuan Hoang
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Cooling System ◽  
Specific Fuel Consumption ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Brake Thermal Efficiency ◽  
Exhaust Gas Temperature ◽  
Low Sulfur

As a rule, the highest permissible sulfur content in the marine fuel must drop below 0.5% from 1 January 2020 for global fleets. As such, ships operating in emission control areas must use low sulfur or non-sulfur fuel to limit sulfur emissions as a source of acid rain. However, that fact has revealed two challenges for the operating fleet: the very high cost of ultra-low sulfur diesel (ULSD) and the installation of the fuel conversion system and the ULSD cooling system. Therefore, a solution that blends ULSD and biodiesel (BO) into a homogeneous fuel with properties equivalent to that of mineral fuels is considered to be significantly effective. In the current work, an advanced ultrasonic energy blending technology has been applied to assist in the production of homogeneous ULSD-BO blends (ULSD, B10, B20, B30, and B50 with blends of coconut oil methyl ester with ULSD of 10%, 20%, 30% and 50% by volume) which is supplied to a small marine diesel engine on a dynamo test bench to evaluate the power and torque characteristics, also to consider the effect of BO fuel on specific fuel consumption exhaust gas temperature and brake thermal efficiency. The use of the ultrasonic mixing system has yielded impressive results for the homogeneous blend of ULSD and BO, which has contributed to improved combustion quality and thermal efficiency. The results have shown that the power, torque, and the exhaust gas temperature, decrease by approximately 9%, 2%, and 4% respectively with regarding the increase of the blended biodiesel rate while the specific fuel consumption and brake thermal efficiency tends to increase of around 6% and 11% with those blending ratios.

Heat Recovery and Burner Modification of an Industrial Tubular Furnace

2015 ◽  
Vol 737 ◽  
pp. 296-300
Author(s):  
Xi Lai Zhang ◽  
Wei Yao
Keyword(s):  
Heat Recovery ◽  
Radiation Heat Transfer ◽  
Exhaust Gas ◽  
Heat Absorption ◽  
Tubular Furnace ◽  
Gas Temperature ◽  
Radiation Heat ◽  
Air Preheater ◽  
Burner Flame ◽  
Exhaust Gas Temperature

The air preheater was installed on the furnace to decrease the exhaust gas temperature and heat the air to about 290°C. A radiant cylinder was added to the radiation section. Swirl flames were formed by adjusting the shape and the installation angles of the burner flame tubes. The radiation heat transfer was strengthened and the heat absorption was enhanced in the radiation section, while the temperature at the outlet of the furnace was decreased. Thus energy was saved by 16.7%.

scholarly journals Diesel engine performance, emissions and combustion characteristics of castor oil blends using pyrolysis

2020 ◽  
Vol 12 (12) ◽  
pp. 168781402097552
Author(s):  
Youssef A. Attai ◽  
Osayed S. Abu-Elyazeed ◽  
Mohamed R. ElBeshbeshy ◽  
Mohamed A. Ramadan ◽  
Mohamed S. Gad
Keyword(s):  
Heat Release ◽  
Fuel Consumption ◽  
Heat Release Rate ◽  
Release Rate ◽  
Thermal Efficiency ◽  
Exhaust Gas ◽  
Cylinder Pressure ◽  
Gas Oil ◽  
Gas Temperature ◽  
Exhaust Gas Temperature

Castor biodiesel (CBD) was manufactured by slow pyrolysis of oil from highly yielded seeds with anhydrous sodium hydroxide catalyst. An experimental study of engine’s performance, emissions and combustion characteristics using biodiesel blended with gas oil in volumetric ratios of 0, 10, 25, 50, 75, and 100% at different loads was performed. Increase of CBD percentage in the blend led to a reduction in engine’s thermal efficiency, cylinder pressure, net heat release rate, and smoke emission. The exhaust gas temperature, specific fuel consumption, unburned hydrocarbon, CO, and nitrogen oxide emissions were increased with the increase of CBD ratio. Biodiesel showed the maximum increase in specific fuel consumption by 10% and the thermal efficiency was decreased by 10.5% about pure diesel. Smoke emissions were decreased for CBD100 by 12% about gas oil. The maximum increases in NOx, CO, HC emissions, and exhaust gas temperature for CBD 100 were 22, 34, 48, and 11%, respectively related to diesel oil. The maximum reductions in cylinder pressure and net heat release rate were 5 and 13% for CBD100 about gas oil, respectively. Biodiesel percentage of 10% showed near values of performance parameters and emissions to gas oil, so, it is recommended as the optimum percentage.

Evaluating the Influence of Biogas Flow Rate and Addition of Cerium Oxide Nanoparticles on the Performance of a Dual Fuel Engine Using Taguchi Method

2017 ◽  
Vol 17 ◽  
pp. 179-193
Author(s):  
M. Feroskhan ◽  
Ismail Saleel
Keyword(s):  
Cerium Oxide ◽  
Flow Rate ◽  
Thermal Efficiency ◽  
Equivalence Ratio ◽  
Volumetric Efficiency ◽  
Dual Fuel ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Brake Thermal Efficiency ◽  
Exhaust Gas Temperature

Biogas is a promising alternative fuel for compression ignition (CI) engines owing to its renewability and carbon neutrality. In this study, biogas was used along with diesel in a CI engine in dual fuel mode, i.e. biogas is inducted along with air and this mixture is ignited by the in-cylinder injection of diesel. The viability of using cerium oxide (CeO2) nanoparticles as an additive to diesel was also explored. The effects of three parameters, viz. biogas flow rate and concentration of CeO2 nanoparticles and applied load on engine performance were investigated under constant speed operation. These parameters were varied in the ranges of 0 - 12 litre/min, 0 - 35 mg/litre and 5 - 22 N.m respectively. The experimental test matrix was reduced to 16 trials using Taguchi’s approach. Performance was quantified in terms of brake thermal efficiency, volumetric efficiency, diesel consumption, exhaust gas temperature and overall equivalence ratio. The criteria for optimum performance were defined as maximum brake thermal and volumetric efficiencies and minimum diesel consumption, exhaust gas temperature and overall equivalence ratio. Optimum operating conditions were identified by evaluating the signal to noise ratio (SNR) for each performance parameter and using the higher-the-better (HTB) or lower-the-better (LTB) condition as applicable. Contributions of individual parameters towards the performance indices were found using ANOVA. Load was found to be the main contributing factor for brake thermal efficiency, exhaust gas temperature and overall equivalence ratio. Biogas flow rate showed significant contribution towards volumetric efficiency. Biogas flow rate and load had comparable influences on diesel consumption. Addition of nanoparticles showed minor contribution towards all the performance parameters.

Sign in / Sign up

Export Citation Format

Share Document