Microstructure and Hardness of Friction Stir Weld Bead on Steel Plate Using W-25%Re Pin Tool

2014 ◽  
Author(s):  
Z. Iqbal ◽  
A. N. Shuaib ◽  
F. Al-Badour ◽  
N. Merah ◽  
A. Bazoune
Keyword(s):  
Friction Stir Welding ◽  
Tool Material ◽  
Dissimilar Materials ◽  
Friction Stir Weld ◽  
Process Conditions ◽  
Steel Microstructure ◽  
Friction Stir ◽  
Diffusion Wear ◽  
Improve Fracture Toughness ◽  
The Right

One of the challenges that impede the use of the relatively new friction stir welding (FSW) process in joining steels and high temperature alloys, as well as dissimilar materials, is the development of the right pin tool material that can stand the severe welding conditions of these alloys. Recent developments in FSW tool materials include tungsten rhenium (W-Re) alloys. The ductile to brittle transition temperature of pure tungsten is reduced by the addition of rhenium (Re).. The addition of Re also improve fracture toughness of the alloy. The major focus of this paper is studying the process of making a friction stir welding bead on mild steel using a proprietary W-25%Re alloy pin tool and investigating the effects of process parameters (i.e. tool rotational and welding speeds) on microstructure, microhardness as well as tool reaction loads. Grain refining of the steel microstructure was observed in all beads. Certain process conditions produced a bead with needle like microstructure with the highest values of hardness. Reaction forces were found to increase with the increase in the tool welding speed and to decrease with the increase of the tool rotational speed. Although the spectroscopic analysis of the beads confirmed the diffusion wear of the tool, the overall tool has shown excellent resistance to mechanical wear.

scholarly journals Parametric Optimization of Friction Stir Welding Factors (FSWF) for Yellow Brass 405-20

2021 ◽  
Author(s):  
Syed Farhan Raza ◽  
Sarmad Ali Khan ◽  
Muhammad Salman Habib ◽  
Naveed Ahmed ◽  
Kashif Ishfaq ◽  
...  
Keyword(s):  
Friction Stir Welding ◽  
Rotational Speed ◽  
Weld Zone ◽  
Tool Material ◽  
Traverse Speed ◽  
Weld Strength ◽  
Friction Stir Weld ◽  
Friction Stir ◽  
Wide Range ◽  
Percent Contribution

Abstract Friction stir welding (FSW) is a green, environmentally amicable, and solid-state joining technology. Industries are really interested in adopting FSW in its various applications e.g., automobile, aerospace, marine, construction, etc. FSW can successfully weld a wide range of materials (similar/dissimilar parent materials) including aluminum, copper, steel, different alloys from these materials, plastics, composites, and this material range is subjected to extension if FSW research efforts develop further in future. FSW of brass has already been accomplished by fewer researchers. In this research, yellow brass 405-20 is, therefore, welded with FSW that was never welded before. In this study, tool material utilized was M2 HSS that was also novel. Effect of two friction stir weld factors (FSWF), rotational speed (RS) and traverse speed (TS), was found on three output parameters i.e., weld temperature, weld strength and weld hardness. Weld temperature was found to be 63.72% of melting point of base metal. A significant improvement in friction stir weld strength (FSWS) was also measured that was found to be 82.78% of the base brass strength. Finally, weld hardness was measured which was found to be 87.80% of original brass hardness. Based on main effects of Anova Analysis, optimal FSW factors were found to be 1450 rpm and 60 mm/min resulting interestingly in maximum (max.)/optimal temperature, max./optimal weld strength, and minimum/optimal hardness. Rotational speed (RS) was found to be significant to affect the weld temperature only at the friction stir weld zone (FSWZ) with the highest percent contribution (PCR) of 65.69%. Transverse speed (TS) was found to be overall insignificant for affecting weld temperature, weld strength and hardness. However, PCR of transverse speed was found to be maximum for affecting weld strength as compared to its PCR towards both weld temperature and weld hardness. Error PCR was found to be the lowest for weld zone temperature, then for weld strength, and finally the highest for weld hardness. Interaction Plots (IPs) were also made for those FSWF which were found to be insignificant and to investigate any combined effect of FSWF on output parameters causing increased error PCR towards weld temperature, weld strength, and weld hardness.

scholarly journals Experimental Comparison of the MIG and Friction Stir Welding Processes for AA 6005 Aluminium Alloy

2015 ◽  
Vol 651-653 ◽  
pp. 1480-1486 ◽  
Author(s):  
Serafino Caruso ◽  
Davide Campanella ◽  
Sebastiano Candamano ◽  
Claudia Varrese ◽  
Fortunato Crea ◽  
...  
Keyword(s):  
Friction Stir Welding ◽  
Welded Joints ◽  
Bending Strength ◽  
Experimental Comparison ◽  
Friction Stir Weld ◽  
Process Conditions ◽  
Al Alloy ◽  
Friction Stir ◽  
Advantages And Disadvantages ◽  
Welding Processes

In this study, the mechanical properties of welded joints of AA 6005 aluminum alloy obtained with friction stir welding (FSW) and conventional metal inert gas welding (MIG) are studied. FSW welds were carried out on a semi-automatic milling machine. The performance of FSW and MIG welded joints were identified using tensile and bending impact tests, as far as the environmental aspects are also included in the discussion. The joints obtained with FSW and MIG processes were also investigated in their microstructure. The results indicate that, the microstructure of the friction stir weld is different from that of MIG welded joint. The weld nugget consists of small grains in FSW than those found in MIG weld. Taking into consideration the process conditions and requirements, FSW and MIG processes were also compared with each other to understand the advantages and disadvantages of the processes for welding applications of studied Al alloy. Better tensile and bending strength were obtained with FSW welded joints.

scholarly journals An Evaluation of Optimal Friction Stir Welding Factors (FSWF) For Yellow Brass 405-20

2022 ◽  
Author(s):  
Syed Farhan Raza ◽  
Sarmad Ali Khan ◽  
Muhammad Salman Habib ◽  
Naveed Ahmed ◽  
Kashif Ishfaq ◽  
...  
Keyword(s):  
Friction Stir Welding ◽  
Rotational Speed ◽  
Weld Zone ◽  
Tool Material ◽  
Traverse Speed ◽  
Microscopic Investigation ◽  
Weld Strength ◽  
Friction Stir Weld ◽  
Friction Stir ◽  
Wide Range

Abstract Friction stir welding (FSW) is a green, environmentally amicable, and solid-state joining technology. FSW can successfully weld a wide range of materials (similar/dissimilar parent materials) including aluminum, copper, steel, different alloys from these materials, plastics, composites. FSW of brass has already been accomplished by fewer researchers. In this research, yellow brass 405-20 is, therefore, welded with FSW that was never welded before. In this study, tool material utilized was M2 HSS that was also novel. Effect of two friction stir weld factors (FSWF), rotational speed (RS) and traverse speed (TS), was found on three output parameters i.e., weld temperature, weld strength and weld hardness. Weld temperature developed, was found to be 63.72% of melting point of base metal. A significant improvement in friction stir weld strength (FSWS) was also measured that was found to be 106.37% of the base brass strength. Finally, weld hardness was measured which was found to be 87.80% of original brass hardness. Based on main effects, optimal FSW factors were found to be 1450 rpm and 60 mm/min resulting interestingly in optimal temperature, optimal weld strength, and optimal hardness. Rotational speed (RS) was found to be significant to affect the weld temperature only at the friction stir weld zone (FSWZ) with the highest percent contribution (PCR) of 65.69%. However, PCR of transverse speed was found to be maximum for affecting weld strength as compared to its PCR towards both weld temperature and weld hardness. Current study was also deepened by microscopic investigation.

Influence of Friction Stir Welding Process on the Weld Formation and Tensile Strength of Titanium and Aluminum Dissimilar Alloys Welded Joint

2011 ◽  
Vol 189-193 ◽  
pp. 3266-3269 ◽  
Author(s):  
Yu Hua Chen ◽  
Peng Wei ◽  
Quan Ni ◽  
Li Ming Ke
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Cross Section ◽  
Welded Joint ◽  
Welding Process ◽  
Dissimilar Materials ◽  
Influence Of Process Parameters ◽  
Friction Stir ◽  
Dissimilar Alloys ◽  
Titanium Aluminum

Titanium alloy TC1 and Aluminum alloy LF6 were jointed by friction stir welding (FSW), and the influence of process parameters on formation of weld surface, cross-section morphology and tensile strength were studied. The results show that, Titanium and Aluminum dissimilar alloy is difficult to be joined by FSW, and some defects such as cracks and grooves are easy to occur. When the rotational speed of stir head(n) is 750r/min and 950r/min, the welding speed(v) is 118mm/min or 150mm/min, a good formation of weld surface can be obtained, but the bonding of titanium/aluminum interface in the cross-section of weld joint is bad when n is 750r/min which results in a low strength joint. When n is 950r/min and v is 118mm/min，the strength of the FSW joint of Titanium/Aluminum dissimilar materials is 131MPa which is the highest．

Features of structure formation processes in AA2024 alloy joints formed by the friction stir welding with bobbin tool

2021 ◽  
Vol 23 (2) ◽  
pp. 98-115
Author(s):  
Alexey Ivanov ◽  
◽  
Valery Rubtsov ◽  
Andrey Chumaevskii ◽  
Kseniya Osipovich ◽  
...  
Keyword(s):  
Friction Stir Welding ◽  
Structure Formation ◽  
Welded Joints ◽  
Heat Input ◽  
Welded Joint ◽  
Welding Process ◽  
Tool Material ◽  
Travel Speed ◽  
Material System ◽  
Friction Stir

Introduction. One of friction stir welding types is the bobbin friction stir welding (BFSW) process, which allows to obtain welded joints in various configurations without using a substrate and axial embedding force, as well as to reduce heat loss and temperature gradient across the welded material thickness. This makes the BFSW process effective for welding aluminum alloys, which properties are determined by their structural-phase state. According to research data, the temperature and strain rate of the welded material have some value intervals in which strong defect-free joints are formed. At the same time, much less attention has been paid to the mechanisms of structure formation in the BFSW process. Therefore, to solve the problem of obtaining defect-free and strong welded joints by BFSW, an extended understanding of the basic mechanisms of structure formation in the welding process is required. The aim of this work is to research the mechanisms of structure formation in welded joint of AA2024 alloy obtained by bobbin tool friction stir welding with variation of the welding speed. Results and discussion. Weld formation conditions during BFSW process are determined by heat input into a welded material, its fragmentation and plastic flow around the welding tool, which depend on the ratio of tool rotation speed and tool travel speed. Mechanisms of joint formation are based on a combination of equally important processes of adhesive interaction in “tool-material” system and extrusion of metal into the region behind the welding tool. Combined with heat dissipation conditions and the configuration of the “tool-material” system, this leads to material extrusion from a welded joint and its decompaction. This results in formation of extended defects. Increasing in tool travel speed reduce the specific heat input, but in case of extended joints welding an amount of heat released in joint increases because of specific heat removal conditions. As a result, the conditions of adhesion interaction and extrusion processes change, which leads either to the growth of existing defects or to the formation of new ones. Taking into account the complexity of mechanisms of structure formation in joint obtained by BFSW, an obtaining of defect-free joints implies a necessary usage of various nondestructive testing methods in combination with an adaptive control of technological parameters directly in course of a welding process.

A State-of-the-Art Review on Solid-State Metal Joining

2018 ◽  
Author(s):  
Wayne Cai ◽  
Glenn Daehn ◽  
Anupam Vivek ◽  
Jingjing Li ◽  
Haris Khan ◽  
...  
Keyword(s):  
Solid State ◽  
State Of The Art ◽  
Dissimilar Materials ◽  
Process Conditions ◽  
Discussion Section ◽  
Friction Stir ◽  
Process Characterization ◽  
Rotary Friction Welding ◽  
Impact Welding ◽  
Solid State Joining

This paper aims at providing a state-of-the-art review of an increasingly important class of joining technologies called solid-state welding. Among many other advantages such as low heat input, solid-state processes are particularly suitable for dissimilar materials joining. In this paper, major solid-state joining technologies such as the linear and rotary friction welding, friction stir welding, ultrasonic welding, impact welding, are reviewed, as well as diffusion and roll bonding. For each technology, the joining process is first depicted, followed by the process characterization, modeling and simulation, monitoring/diagnostics/NDE, and ended with concluding remarks. A discussion section is provided after reviewing all the technologies on the common critical factors that affect the solid-state processes such as the joining mechanisms, chemical and materials compatibility, surface properties, and process conditions. Finally, the future outlook is presented.

scholarly journals Analysis of the influence of position of welding materials on the FSW seams properties for three dissimilar aluminium alloy

2018 ◽  
Vol 178 ◽  
pp. 03003 ◽  
Author(s):  
Ana Bosneag ◽  
Marius Adrian Constantin ◽  
Eduard Niţu ◽  
Monica Iordache
Keyword(s):  
Friction Stir Welding ◽  
Aluminium Alloy ◽  
Process Parameters ◽  
Arc Welding ◽  
Welding Process ◽  
Dissimilar Materials ◽  
Workpiece Material ◽  
Friction Stir ◽  
Welding Joints ◽  
Welding Materials

Friction Stir Welding, abbreviated FSW is a new and innovative welding process. This welding process is increasingly required, more than traditional arc welding, in industrial environment such us: aeronautics, shipbuilding, aerospace, automotive, railways, general fabrication, nuclear, military, robotics and computers. FSW, more than traditional arc welding, have a lot of advantages, such us the following: it uses a non-consumable tool, realise the welding process without melting the workpiece material, can be realised in all positions (no weld pool), results of good mechanical properties, can use dissimilar materials and have a low environmental impact. This paper presents the results of experimental investigation of friction stir welding joints to three dissimilar aluminium alloy AA2024, AA6061 and AA7075. For experimenting the value of the input process parameters, the rotation speed and advancing speed were kept the same and the position of plates was variable. The exit date recorded in the time of process and after this, will be compared between them and the influence of position of plate will be identified on the welding seams properties and the best position of plates for this process parameters and materials.

scholarly journals 3D-Printed Tool Shoulder Design for the Analogue Modelling of Bobbin Friction Stir Weld Joint Quality

2021 ◽  
Vol 21 (1) ◽  
pp. 27-42
Author(s):  
A. Tamadon ◽  
D. J. Pons ◽  
K. Chakradhar ◽  
J. Kamboj ◽  
D. Clucas
Keyword(s):  
Friction Stir Welding ◽  
Cross Sections ◽  
Weld Joint ◽  
Flow Patterns ◽  
Friction Stir Weld ◽  
Butt Weld ◽  
Friction Stir ◽  
Tool Shoulder ◽  
Analogue Modelling ◽  
3D Printed

Abstract A variety of tool shoulder designs comprising three families i.e. blade, spiral and circular shaped scrolls, were produced to improve the material flow and restrictions to avoid the tunnel void. The bobbin tools were manufactured by 3D printing additive manufacturing technology using solid filament. The butt weld joint was produced by each tool using plasticine as the workpiece material. The apparent surface features and bi-colour cross-sections provided a physical flow comparison among the shoulder designs. For the bobbin friction stir welding (BFSW), the tool shoulder with a three-spiral design produced the most stability with the best combination of the flow patterns on surface and cross-sections. The circular family tools showed a suitable intermixing on the surface pattern, while the blade scrolls showed better flow features within the cross-sections. The flow-driven effect of the shoulder features of the bobbin-tool design (inscribed grooves) was replicated by the 3D-printed tools and the analogue modelling of the weld samples. Similar flow patterns were achieved by dissimilar aluminium-copper weld, validating the accuracy of the analogue plasticine for the flow visualization of the bobbin friction stir welding.

Friction Stir Welding of Elements Made of Cast Aluminium Alloys

2014 ◽  
Vol 59 (1) ◽  
pp. 385-392
Author(s):  
B. Rams ◽  
A. Pietras ◽  
K. Mroczka
Keyword(s):  
Friction Stir Welding ◽  
Aluminium Alloy ◽  
Aluminium Alloys ◽  
Welding Parameters ◽  
Process Conditions ◽  
Friction Stir ◽  
Seam Weld ◽  
Cast Aluminium ◽  
Weld Structure ◽  
Welding Stability

Abstract The article presents application of FSW method for joining elements made of cast aluminium alloys which are hardly weldable with other known welding techniques. Research’s results of plasticizing process of aluminium and moulding of seam weld during different FSW process’ conditions were also presented. Influence of welding parameters, shape and dimensions of tool on weld structure, welding stability and quality was examined. Application of FSW method was exemplified on welding of hemispheres for valves made of cast aluminium alloy EN AC-43200.

Sign in / Sign up

Export Citation Format

Share Document