Application of an Improved Streamline Curvature Approach to a Modern, Two-Stage Transonic Fan: Comparison With Data and CFD

2002 ◽  
Author(s):  
Keith M. Boyer ◽  
Walter F. O’Brien
Keyword(s):  
Three Dimensional ◽  
Operating Conditions ◽  
Navier Stokes ◽  
Model Parameters ◽  
Two Stage ◽  
Streamline Curvature ◽  
Wide Range ◽  
Improved Model ◽  
Transonic Fan ◽  
Streamline Curvature Method

A streamline curvature method with improvements to key loss models is applied to a two-stage, low aspect ratio, transonic fan with design tip relative Mach number of approximately 1.65. Central to the improvements is the incorporation of a physics-based shock model. The attempt here is to capture the effects of key flow phenomena relative to the off-design performance of the fan. A quantitative analysis regarding solution sensitivities to model parameters that influence the key phenomena over a wide range of operating conditions is presented. Predictions are compared to performance determined from overall and interstage measurements, as well as from a three-dimensional, steady, Reynolds-averaged Navier-Stokes method applied across the first rotor. Overall and spanwise comparisons demonstrate that the improved model gives reasonable performance trending and generally accurate results. The method can be used to provide boundary conditions to higher-order solvers, or implemented within novel approaches using the streamline curvature method to explore complex engine-inlet integration issues, such as time-variant distortion.

Nonlinear Dynamic Model of a Two-Stage Pressure Relief Valve for Designers

2001 ◽  
Vol 124 (1) ◽  
pp. 62-66 ◽  
Author(s):  
Pei-Sun Zung ◽  
Ming-Hwei Perng
Keyword(s):  
Dynamic Model ◽  
Nonlinear Dynamic ◽  
Dynamic Models ◽  
Operating Conditions ◽  
Model Parameters ◽  
Nonlinear Dynamic Model ◽  
Relief Valve ◽  
Two Stage ◽  
Pressure Relief ◽  
Wide Range

This paper presents a handy nonlinear dynamic model for the design of a two stage pilot pressure relief servo-valve. Previous surveys indicate that the performance of existing control valves has been limited by the lack of an accurate dynamic model. However, most of the existing dynamic models of pressure relief valves are developed for the selection of a suitable valve for a hydraulic system, and assume model parameters which are not directly controllable during the manufacturing process. As a result, such models are less useful for a manufacturer eager to improve the performance of a pressure valve. In contrast, model parameters in the present approach have been limited to dimensions measurable from the blue prints of the valve such that a specific design can be evaluated by simulation before actually manufacturing the valve. Moreover, the resultant model shows excellent agreement with experiments in a wide range of operating conditions.

Shape Optimization of Transonic Compressor Blades Using Quasi-3D Flow Physics

2000 ◽  
Author(s):  
June Chung ◽  
Ki D. Lee
Keyword(s):  
Design Method ◽  
Computational Cost ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Rotor Blades ◽  
Navier Stokes ◽  
Compressor Blades ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Wide Range

A design method for transonic compressor rotor blades is developed based on Navier-Stokes physics. The method is applied to optimize the blade sections at several span stations, and new three-dimensional blades are constructed by interpolating the geometry of the designed blade sections. The method is demonstrated with NASA Rotor 37, producing new rotor blades with improved adiabatic efficiency over a wide range of operating conditions. The results indicate that the developed design process can find improved designs at an affordable computational cost.

Unsteady Three-Dimensional Analysis of Inlet Distortion in a Transonic Fan

2006 ◽  
Author(s):  
Peng Sun ◽  
Guotal Feng
Keyword(s):  
Shock Wave ◽  
Total Pressure ◽  
Large Scale ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Inlet Distortion ◽  
Flow Loss ◽  
Large Scale Vortex ◽  
Total Temperature ◽  
Transonic Fan

A time-accurate three-dimensional Navier-Stokes solver of the unsteady flow field in a transonic fan was carried out using "Fluent-parallel" in a parallel supercomputer. The numerical simulation focused on a transonic fan with inlet square wave total pressure distortion and the analysis of result consisted of three aspects. The first was about inlet parameters redistribution and outlet total temperature distortion induced by inlet total pressure distortion. The pattern and causation of flow loss caused by pressure distortion in rotor were analyzed secondly. It was found that the influence of distortion was different at different radial positions. In hub area, transportation-loss and mixing-loss were the main loss patterns. Distortion not only complicated them but enhanced them. Especially in stator, inlet total pressure distortion induced large-scale vortex, which produced backflow and increased the loss. While in casing area, distortion changed the format of shock wave and increased the shock loss. Finally, the format of shock wave and the hysteresis of rotor to distortion were analyzed in detail.

The Extension of a Solution-Adaptive Three-Dimensional Navier–Stokes Solver Toward Geometries of Arbitrary Complexity

1993 ◽  
Vol 115 (2) ◽  
pp. 283-295 ◽  
Author(s):  
W. N. Dawes
Keyword(s):  
Guide Vane ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Centrifugal Impeller ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Wide Range ◽  
Nozzle Guide Vane ◽  
Recent Developments ◽  
Nozzle Guide

This paper describes recent developments to a three-dimensional, unstructured mesh, solution-adaptive Navier–Stokes solver. By adopting a simple, pragmatic but systematic approach to mesh generation, the range of simulations that can be attempted is extended toward arbitrary geometries. The combined benefits of the approach result in a powerful analytical ability. Solutions for a wide range of flows are presented, including a transonic compressor rotor, a centrifugal impeller, a steam turbine nozzle guide vane with casing extraction belt, the internal coolant passage of a radial inflow turbine, and a turbine disk cavity flow.

Time-Averaged Heat Transfer and Pressure Measurements and Comparison With Prediction for a Two-Stage Turbine

1994 ◽  
Vol 116 (1) ◽  
pp. 14-22 ◽  
Author(s):  
M. G. Dunn ◽  
J. Kim ◽  
K. C. Civinskas ◽  
R. J. Boyle
Keyword(s):  
Surface Pressure ◽  
Space Shuttle ◽  
Three Dimensional ◽  
Stanton Number ◽  
Navier Stokes ◽  
Pressure Measurements ◽  
Two Stage ◽  
Pressure Transducers ◽  
Pressure Distributions ◽  
Main Engine

Time-averaged Stanton number and surface-pressure distributions are reported for the first-stage vane row and the first-stage blade row of the Rocketdyne Space Shuttle Main Engine two-stage fuel-side turbine. These measurements were made at 10, 50, and 90 percent span on both the pressure and suction surfaces of the component. Stanton-number distributions are also reported for the second-stage vane at 50 percent span. A shock tube is used as a short-duration source of heated and pressurized air to which the turbine is subjected. Platinum thin-film gages are used to obtain the heat-flux measurements and miniature silicone-diaphragm pressure transducers are used to obtain the surface pressure measurements. The first-stage vane Stanton number distributions are compared with predictions obtained using a quasi-three dimensional Navier–Stokes solution and a version of STAN5. This same N–S technique was also used to obtain predictions for the first blade and the second vane.

scholarly journals Improvement of Pump Performance at Off-Design Conditions

1985 ◽  
Author(s):  
J. Paulon ◽  
C. Fradin ◽  
J. Poulain
Keyword(s):  
Experimental Study ◽  
Flow Field ◽  
Mass Flow ◽  
Flow Characteristic ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Pump Performance ◽  
Wide Range ◽  
Mass Flows ◽  
Design Value

Industrial pumps are generally used in a wide range of operating conditions from almost zero mass flow to mass flows larger than the design value. It has been often noted that the head-mass flow characteristic, at constant speed, presents a negative bump as the mass flow is somewhat smaller than the design mass flows. Flow and mechanical instabilities appear, which are unsafe for the facility. An experimental study has been undertaken in order to analyze and if possible to palliate these difficulties. A detailed flow analyzis has shown strong three dimensional effects and flow separations. From this better knowledge of the flow field, a particular device was designed and a strong attenuation of the negative bump was obtained.

scholarly journals A Review of Passive Micromixers with a Comparative Analysis

Micromachines ◽  
2020 ◽  
Vol 11 (5) ◽  
pp. 455 ◽  
Author(s):  
Wasim Raza ◽  
Shakhawat Hossain ◽  
Kwang-Yong Kim
Keyword(s):  
Reynolds Number ◽  
Comparative Analysis ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Number Range ◽  
Pressure Drops ◽  
Convection Diffusion ◽  
Wide Range ◽  
Quantitative Analyses ◽  
Mixing Costs

A wide range of existing passive micromixers are reviewed, and quantitative analyses of ten typical passive micromixers were performed to compare their mixing indices, pressure drops, and mixing costs under the same axial length and flow conditions across a wide Reynolds number range of 0.01–120. The tested micromixers were selected from five types of micromixer designs. The analyses of flow and mixing were performed using continuity, Navier-Stokes and convection-diffusion equations. The results of the comparative analysis were presented for three different Reynolds number ranges: low-Re (Re ≤ 1), intermediate-Re (1 < Re ≤ 40), and high-Re (Re > 40) ranges, where the mixing mechanisms are different. The results show a two-dimensional micromixer of Tesla structure is recommended in the intermediate- and high-Re ranges, while two three-dimensional micromixers with two layers are recommended in the low-Re range due to their excellent mixing performance.

Shroud Leakage Modeling of the Flow in a Two Stage Axial Test Turbine

2008 ◽  
Author(s):  
M. Pau ◽  
F. Cambuli ◽  
N. Mandas
Keyword(s):  
Three Dimensional ◽  
Design Tool ◽  
Navier Stokes ◽  
Computational Time ◽  
Leakage Flow ◽  
Two Stage ◽  
Flow Paths ◽  
Flow Interaction ◽  
Full Calculation ◽  
Mainstream Flow

Three dimensional steady multistage calculations, using mixing plane approach, are presented for two different blade geometries in a two stage axial test turbine with shrouded blades. A 3D multiblock Navier-Stokes finite volume solver (TBLOCK) has been used in all the simulations. In order to study shroud leakage flow effects the whole shroud cavity geometry has been modeled, overcoming most of the limitations of simple shroud leakage model in calculating fluid flow over complex geometries. Numerical investigations are mainly focused on assessing the ability of the solver to be used as multistage design tool for modeling leakage-mainstream flow interaction. Several calculations are compared. The first computes the main blade flow path with no modeling of the shroud cavities. The second includes the modeling of the shroud cavities for a zero leakage mass flow rate. Finally a multiblock calculation which models all the leakage flow paths and shroud cavities has been carried out for two different levels of shroud seal clearance. It is found that neglecting shroud leakage significantly alters the computed velocity profiles and loss distributions, for both the computed blade geometries. A numerically predicted shroud leakage offset loss is presented for the two considered blade geometries, focusing on the relative importance of the leakage flow, re-entry mixing losses, and inlet and exit shroud cavity effect. Results demonstrates that full calculation of leakage flow paths and cavities is required to obtain reliable results, indicating the different effects of the leakage-to-mainstream flow interaction on the blade geometries computed. Despite a slight increase in the computational time, multiblock approach in handling leakage flow problem can now-days be used as a practical tool in the blade design process and routine shroud leakage calculations.

Improved Approach to the Streamline Curvature Method in Turbomachinery

1987 ◽  
Vol 109 (3) ◽  
pp. 213-217 ◽  
Author(s):  
S. Abdallah ◽  
R. E. Henderson
Keyword(s):  
Flow Field ◽  
Velocity Gradient ◽  
Numerical Solutions ◽  
Three Dimensional ◽  
Second Order ◽  
Curvilinear Coordinates ◽  
First Order ◽  
Streamline Curvature ◽  
Stators And Rotors ◽  
Streamline Curvature Method

Quasi three dimensional blade-to-blade solutions for stators and rotors of turbomachines are obtained using the Streamline Curvature Method (SLCM). The first-order velocity gradient equation of the SLCM, traditionally solved for the velocity field, is reformulated as a second-order elliptic differential equation and employed in tracing the streamtubes throughout the flow field. The equation of continuity is then used to calculate the velocity. The present method has the following advantages. First, it preserves the ellipticity of the flow field in the solution of the second-order velocity gradient equation. Second, it eliminates the need for curve fitting and strong smoothing under-relaxation in the classical SLCM. Third, the prediction of the stagnation streamlines is a straightforward matter which does not complicate the present procedure. Finally, body-fitted curvilinear coordinates (streamlines and orthogonals or quasi-orthogonals) are naturally generated in the method. Numerical solutions are obtained for inviscid incompressible flow in rotating and non-rotating passages and the results are compared with experimental data.

scholarly journals Performance and Modeling of a Two-Stage Light Gas Gun Driven by Gaseous Detonation

2020 ◽  
Vol 10 (12) ◽  
pp. 4383
Author(s):  
Weiqi Tang ◽  
Qiu Wang ◽  
Bingchen Wei ◽  
Jiwei Li ◽  
Jinping Li ◽  
...  
Keyword(s):  
Tube Wall ◽  
Numerical Approach ◽  
Operating Conditions ◽  
Gaseous Detonation ◽  
Two Stage ◽  
Piston Velocity ◽  
Gas Gun ◽  
Small Influence ◽  
Improved Model ◽  
Gas Guns

A two-stage light gas gun driven by gaseous detonation was newly constructed, which can make up for the disadvantages of the insufficient driving capability of high-pressure gas and the constraints of gunpowder. The performance of the gas gun was investigated through experiments and a quasi-one-dimensional modeling of it was also developed and described in detail. The model accounts for the friction and heat transfer to the tube wall for gases by adding a source term. An improved model has been established to consider the inertial loads in the piston or projectile and model the friction force with the tube wall. Besides, the effects of pump tube pressure on the performance of the gas gun are also investigated numerically. Simulations of the pressure histories in the pump tube and the piston and projectile velocities were conducted. A good agreement was observed between the computational predictions and experimental results. The results showed that the friction between the piston and wall had only small influence on the piston velocity. The proposed numerical approach is suitable for the development of two-stage light gas guns and tests of the operating conditions.

Sign in / Sign up

Export Citation Format

Share Document