The Characteristics of Radial Turbines for Small Gas Turbines

2003 ◽  
Author(s):  
C. Rodgers
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Structural Integrity ◽  
Velocity Ratio ◽  
Turbine Rotor ◽  
Flow Coefficient ◽  
Cycle Performance ◽  
Radial Turbine ◽  
Auxiliary Power Units ◽  
Axial Turbines

Inward flow radial and mixed flow turbines are effectively utilized in both small gas turbine auxiliary power units (APU’s) and turbochargers, where moderately high levels of efficiency can be readily attained with simple cast components, less sensitive to blade end-gap clearances than axial turbines. This paper provides an overview of radial turbine performance characteristics for small gas turbine applications as basically influenced by specific speed, velocity ratio, exit flow coefficient, and rotor tip to exducer root mean square (RMS) diameter ratio. Since turbine rotor mass and inertia play important roles in structural integrity and engine acceleration characteristics, the importance of turbine velocity ratio selection upon rotor tip diameter, and cycle performance are discussed. The effects of rotor reaction on radial turbine flow versus pressure characteristics are examined pertinent to engine matching requirements. Engine transient performance is addressed, as influenced by turbine operation towards and beyond runaway conditions.

Radial Turbines — Blade Number and Reaction Effects

2000 ◽  
Author(s):  
C. Rodgers
Keyword(s):  
Gas Turbine ◽  
Structural Integrity ◽  
Velocity Ratio ◽  
Past Research ◽  
Turbine Rotor ◽  
Friction Model ◽  
Radial Turbine ◽  
Auxiliary Power ◽  
Auxiliary Power Units ◽  
Axial Turbines

Inward flow radial and mixed flow turbines are effectively utilized in both turbochargers and small gas turbine auxiliary power units (APU’s), where moderately high levels of efficiency can be readily attained with simple cast components, less sensitive to blade endgap clearances than axial turbines. This paper first provides an overview of radial turbine performance characteristics for turbocharger and gas turbine applications as basically influenced by specific speed, reaction, velocity ratio, and rotor tip to exducer root mean square (RMS) diameter ratio. Since turbine rotor mass and inertia play important roles in structural integrity and engine acceleration characteristics, the effects of rotor blade solidity on turbine efficiency are then discussed based upon past research, and supported by analysis of a one dimensional friction model of the rotor passage. Finally the effects of rotor reaction on radial turbine flow versus pressure characteristics are examined pertinent to engine matching requirements.

Bearing Housing Design for Vibration Control, Using Tilting Pad Bearings Instead of Lemon-Bore Type on a Gas Turbine

2020 ◽  
Author(s):  
Chippa Anil ◽  
Aparna Satheesh ◽  
Babu Santhanagopalakrishnan ◽  
Marcin Bielecki
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Structural Integrity ◽  
Plane Surface ◽  
Rotor Dynamics ◽  
Turbine Rotor ◽  
Outer Diameter ◽  
Housing Design ◽  
Tilting Pad ◽  
And Performance

Abstract Heavy duty gas turbines are usually equipped with hydrodynamic bearings which are either lemon-bore or tilting pad type. Baker Hughes legacy gas turbines use these two types of bearings, and its selection is based on 1) considering pros & cons from Rotor dynamics, 2) bearing performance, 3) bearing housing stiffness, 4) vibration detection & control. Non-contact probes are used to monitor the vibrations of rotor. Majority of legacy gas turbines are not equipped with these probes. Due to this fact, over the years it resulted in non-detection of dynamics & vibration issue, which caused frequent bearing replacement. As the increase in industry demand to apply and measure vibrations using non-contact probes on bearings, an effort was made by Baker Hughes to implement these on existing fleet units. Also, in order to increase rotor dynamics stability of low-pressure rotor, to improve bearing life and performance, effort was made to replace lemon-bore bearings with tilting pad. This paper demonstrates efforts made to design the titling pad which would fit within envelop of already available bearing housing. Bearing/shaft clearance, bearing performance, modification of bearing retainer clearances are the mandatory tasks which would be dealt in this study. The swap of bearing type, and its effect on whole gas turbine rotor dynamic stability, checking the frequency crossovers with Campbell diagram would also be dealt in this paper. This paper also focuses on assessment on oil passage routing, temperature & proximity probe instrumentation routing design. Re-design is performed by analyzing various configuration, assessing different sensitivity studies & validation of modified bearing housing from structural integrity, ultimate load capability, & split plane oil leakage retention and its comparison with baseline are most important aspects of finalization of this change, which will be showcased in this paper. Instrumentation routing was a critical task when the considering bearing replacement from lemon-bore to tilting pad. As lemon-bore type bearings just have an elliptical inner surface, it’s quite easy to install the thermocouples into a simple hole. But as replacement has tilting pads, the challenge is to instrument the pads without effecting their movement and functionality. Such best practices are also dealt in this paper. Comparison of tilting-pad with lemon-bore, considering the fixed shaft diameter, the retainer outer diameter of tilting pad is higher than lemon-bore. This effect has a change in bearing seat on bearing housing, thereby reducing the effective stiffness of the housing, and the reduced split plane surface. To tackle this situation, several sensitivities were executed, by re-modifying the bolts and bolt holes on the existing housing, without modifying the housing envelop.

Aerodynamic Design and Numerical Investigation on Overall Performance of a Micro Radial Turbine With Millimeter-Scale

2009 ◽  
Author(s):  
Lei Fu ◽  
Yan Shi ◽  
Qinghua Deng ◽  
Zhenping Feng
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Turbine Rotor ◽  
Rotor Blades ◽  
Micro Gas Turbine ◽  
Radial Turbine ◽  
Overall Performance ◽  
Low Reynolds ◽  
Exit Mach Number ◽  
Installation Technology

For millimeter-scale microturbines, the principal challenge is to achieve a design scheme to meet the aerothermodynamics, geometry restriction, structural strength and component functionality requirements while in consideration of the applicable materials, realizable manufacturing and installation technology. This paper mainly presents numerical investigations on the aerothermodynamic design, geometrical design and overall performance prediction of a millimeter-scale radial turbine with rotor diameter of 10mm. Four kinds of turbine rotor profiles were designed, and they were compared with one another in order to select the suitable profile for the micro radial turbine. The leaving velocity loss in micro gas turbines was found to be a large source of inefficiency. The approach of refining the geometric structure of rotor blades and the profile of diffuser were adopted to reduce the exit Mach number thus improving the total-static efficiency. Different from general gas turbines, micro gas turbines are operated in low Reynolds numbers, 104∼105, which has significant effect on flow separation, heat transfer and laminar to turbulent flow transition. Based on the selected rotor profile, several micro gas turbine configurations with different tip clearances of 0.1mm, 0.2mm and 0.3mm, respectively; two different isothermal wall conditions; and two laminar-turbulent transition models were investigated to understand the particular influence of low Reynolds number. These influences on the overall performance of the micro gas turbine were analyzed in details. The results indicate that these configurations should be included and emphasized during the design process of the millimeter-scale micro radial turbines.

Development and Evaluation of a High Resolution Turbine Pyrometer System

2001 ◽  
Author(s):  
Torsten Eggert ◽  
Bjoern Schenk ◽  
Helmut Pucher
Keyword(s):  
High Resolution ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Turbine Rotor ◽  
Measurement Range ◽  
Test Facility ◽  
Radial Turbine ◽  
Measurement Results ◽  
Technical University ◽  
Industrial Gas Turbine

Optical pyrometers provide many advantages over intrusive measuring techniques in determining the spatial and time varying temperature distribution of fast rotating components in gas turbines. This paper describes the development and evaluation of a versatile high resolution pyrometer system and its application to radial turbine rotor temperature mapping as has been done in a R&D project at the Technical University Berlin under funding from Siemens Power Generation (KWU). The development goal was a pyrometer system with a temporal resolution of 1μs, a minimum field of view of 1 mm, and a measurement range from 600 to 1500°C. A prototype of the pyrometer system has been built and tested at the small gas turbine test facility of the Technical University Berlin. The system yielded excellent results with respect to measurement uncertainty, resolution, and reliability. Finally, measurement results obtained with the new system on a radial turbine rotor and on a heavy duty industrial gas turbine are compared with measurements conducted with a commercially available turbine pyrometer system.

Development and Evaluation of a High-Resolution Turbine Pyrometer System

2002 ◽  
Vol 124 (3) ◽  
pp. 439-444 ◽  
Author(s):  
Torsten Eggert ◽  
Bjoern Schenk ◽  
Helmut Pucher
Keyword(s):  
High Resolution ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Turbine Rotor ◽  
Measurement Range ◽  
Test Facility ◽  
Radial Turbine ◽  
Measurement Results ◽  
Technical University ◽  
Industrial Gas Turbine

Optical pyrometers provide many advantages over intrusive measuring techniques in determining the spatial and time varying temperature distribution of fast rotating components in gas turbines. This paper describes the development and evaluation of a versatile high-resolution pyrometer system and its application to radial turbine rotor temperature mapping as has been done in a R&D project at the Technical University Berlin under funding from Siemens Power Generation (KWU). The development goal was a pyrometer system with a temporal resolution of 1 μs, a minimum field of view of 1 mm, and a measurement range from 600 to 1500°C. A prototype of the pyrometer system has been built and tested at the small gas turbine test facility of the Technical University Berlin. The system yielded excellent results with respect to measurement uncertainty, resolution, and reliability. Finally, measurement results obtained with the new system on a radial turbine rotor and on a heavy duty industrial gas turbine are compared with measurements conducted with a commercially available turbine pyrometer system.

Some Effects of Size on the Performances of Small Gas Turbines

2003 ◽  
Author(s):  
C. Rodgers
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Engine Performance ◽  
Lessons Learned ◽  
Rapid Expansion ◽  
Cycle Performance ◽  
Frictional Drag ◽  
Component Design ◽  
Turbine Component ◽  
Performance Development

By the new millennia gas turbine technology standards the size of the first gas turbines of Von Ohain and Whittle would be considered small. Since those first pioneer achievements the sizes of gas turbines have diverged to unbelievable extremes. Large aircraft turbofans delivering the equivalent of 150 megawatts, and research micro engines designed for 20 watts. Microturbine generator sets rated from 2 to 200kW are penetrating the market to satisfy a rapid expansion use of electronic equipment. Tiny turbojets the size of a coca cola can are being flown in model aircraft applications. Shirt button sized gas turbines are now being researched intended to develop output powers below 0.5kW at rotational speeds in excess of 200 Krpm, where it is discussed that parasitic frictional drag and component heat transfer effects can significantly impact cycle performance. The demarcation zone between small and large gas turbines arbitrarily chosen in this treatise is rotational speeds of the order 100 Krpm, and above. This resurgence of impetus in the small gas turbine, beyond that witnessed some forty years ago for potential automobile applications, fostered this timely review of the small gas turbine, and a re-address of the question, what are the effects of size and clearances gaps on the performances of small gas turbines?. The possible resolution of this question lies in autopsy of the many small gas turbine component design constraints, aided by lessons learned in small engine performance development, which are the major topics of this paper.

Experience With Large Heavy-Duty Gas Turbine Rotors

1981 ◽  
Author(s):  
O. R. Schmoch ◽  
B. Deblon
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Turbine Rotor ◽  
Strength Properties ◽  
Operating Conditions ◽  
Material Strength ◽  
Heavy Duty ◽  
Turbine Rotors ◽  
Heavy Duty Gas Turbine ◽  
Response To Temperature

The peripheral speeds of the rotors of large heavy-duty gas turbines have reached levels which place extremely high demands on material strength properties. The particular requirements of gas turbine rotors, as a result of the cycle, operating conditions and the ensuing overall concepts, have led different gas turbine manufacturers to produce special structural designs to resolve these problems. In this connection, a report is given here on a gas turbine rotor consisting of separate discs which are held together by a center bolt and mutually centered by radial serrations in a manner permitting expansion and contraction in response to temperature changges. In particular, the experience gained in the manufacture, operation and servicing are discussed.

Principles of Imitation for the Loading of the Test Bench for Gas Turbines of Gas Pumping Units, Adequate to Real Conditions

2021 ◽  
Vol 13 (24) ◽  
pp. 13678
Author(s):  
Anton Petrochenkov ◽  
Aleksandr Romodin ◽  
Vladimir Kazantsev ◽  
Aleksey Sal’nikov ◽  
Sergey Bochkarev ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Simulation Models ◽  
Turbine Rotor ◽  
Operating Conditions ◽  
Automation System ◽  
Model Free ◽  
Gas Pumping ◽  
Pumping Units

The purpose of the study is to analyze the prospects for the development of loading methods for gas turbines as well as to develop a mathematical model that adequately describes the real operating conditions of the loading system at various loads and rotation speeds. A comparative analysis of the most common methods and technical means of loading the shafts of a free turbine at gas turbine plants intended for operation as part of gas pumping units is presented. Based on the results of the analysis, the expediency of using the loading model “Free Power Turbine Rotor–Hydraulic Brake” as a load simulation is shown. Recommendations for the creation of an automation system for the load testing of power plants have been developed. Mathematical models and Hardware-in-the-Loop simulation models of power plants have been developed and tested. One of the most important factors that predetermine the effectiveness of the loading principle is the possibility of software implementation of the loading means using software control systems that provide the specified loading parameters of the gas turbine.

Micro Gas Turbine With Ceramic Nozzle and Rotor

2005 ◽  
Author(s):  
Takayuki Matsunuma ◽  
Hiro Yoshida ◽  
Norihiko Iki ◽  
Takumi Ebara ◽  
Satoshi Sodeoka ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Turbine Rotor ◽  
Total Power ◽  
Inlet Temperature ◽  
Present System ◽  
Outlet Temperature ◽  
Micro Gas Turbine ◽  
Buffer Material ◽  
Inconel 713C

A series of operation tests of a ceramic micro gas turbine has been successfully carried out. The baseline machine is a small single-shaft turbojet engine (J-850, Sophia Precision Corp.) with a centrifugal compressor, an annular type combustor, and a radial turbine. As a first step, an Inconel 713C alloy turbine rotor of 55 mm in diameter was replaced with a ceramic rotor (SN-235, Kyocera Corporation). A running test was conducted at rotational speeds of up to 140,000 rpm in atmospheric air. At this rotor speed, the compression pressure ratio and the thrust were 3 and 100 N, respectively. The total energy level (enthalpy and kinetic energy) of the exhaust gas jet was 240 kW. If, for example, it is assumed that 10% of the total power of the exhaust jet gas was converted into electricity, the present system would correspond to a generator with 24 kW output power. The measured turbine outlet temperature was 950°C (1,740°F) and the turbine inlet temperature was estimated to be 1,280°C (2,340°F). Although the ceramic rotor showed no evidence of degradation, the Inconel nozzle immediately in front of the turbine rotor partially melted in this rotor condition. As a second step, the Inconel turbine nozzle and casing were replaced with ceramic parts (SN-01, Ohtsuka Ceramics Inc.). The ceramic nozzle and case were supported by metal parts. Through tests with the ceramic nozzle, it became evident that one of the key technologies for the development of ceramic gas turbines is the design of the interface between the ceramic components and the metallic components, because the difference between the coefficients of linear thermal expansion of the ceramic and metal produces large thermal stress at their interface in the high-temperature condition. A buffer material made of alumina fiber was therefore introduced at the interface between the ceramic and metal.

Solar Hybrid Combined Cycle Performance Prediction: Influence of GT Model and Spool Arrangement

2012 ◽  
Author(s):  
G. Barigozzi ◽  
G. Bonetti ◽  
G. Franchini ◽  
A. Perdichizzi ◽  
S. Ravelli
Keyword(s):  
Gas Turbine ◽  
Performance Prediction ◽  
Gas Turbines ◽  
Control Strategies ◽  
Rankine Cycle ◽  
Simulation Method ◽  
Power Input ◽  
Combined Cycle ◽  
Cycle Performance ◽  
Solar Field

A modeling procedure was developed to simulate design and off-design operation of Hybrid Solar Gas Turbines in a combined cycle (CC) configuration. The system includes an heliostat field, a receiver and a commercial gas turbine interfaced with a conventional steam Rankine cycle. Solar power input is integrated in the GT combustor by natural gas. Advanced commercial software tools were combined together to get design and off-design performance prediction: TRNSYS® was used to model the solar field and the receiver while the gas turbine and steam cycle simulations were performed by means of Thermoflex®. Three GT models were considered, in the 35–45 MWe range: a single shaft engine (Siemens SGT800) and two two-shaft engines (the heavy-duty GT Siemens SGT750 and the aero derivative GE LM6000 PF). This in order to assess the influence of different GT spool arrangements and control strategies on GT solarization. The simulation method provided an accurate modeling of the daily solar hybrid CC behavior to be compared against the standard CC. The effects of solarization were estimated in terms of electric power and efficiency reduction, fossil fuel saving and solar energy to electricity conversion efficiency.

Sign in / Sign up

Export Citation Format

Share Document