On the Breakup Process of Round Liquid Jets in Gaseous Crossflows at Low Weber Number

2013 ◽  
Author(s):  
Shao-lin Wang ◽  
Yong Huang ◽  
Fang Wang ◽  
Zhi-lin Liu ◽  
Lei Liu
Keyword(s):  
Weber Number ◽  
High Speed ◽  
Droplet Diameter ◽  
Liquid Jets ◽  
Breakup Process ◽  
Ohnesorge Number ◽  
Propulsion Systems ◽  
Momentum Ratio ◽  
Breakup Length ◽  
Primary Breakup

Liquid jets in cross air flows are widely used and play an important role in propulsion systems, such as ramjet combustors. In this paper, experiments were carried out to investigate the properties of the primary breakup of liquid jets in subsonic transverse airflows at low Weber number. The test ranges included crossflow Weber numbers of 0.5–6.7, liquid-to-gas momentum ratios of 3–120, and Ohnesorge number of 0.0086. Four different injectors with diameter 0.4mm, 0.5mm, 0.6mm and 1mm have been used. A high speed camera was used to observe the jet column breakup process. Results show that the surface wavelength decreases not only with the increase of the gas Weber number but also with the increase of the momentum ratio. The breakup length decreases with the increase of the gas Weber number, in addition to its increase with the increase of the momentum ratio. The droplet diameter decreases with the increase of both the gas Weber number and momentum ratio, although the gas Weber number will dominate the breakup process. The surface wavelength, breakup length, and droplet diameter were also analyzed with to obtain semi-theoretical correlations.

Jet Breakup and Droplet Formation in Immiscible Liquid-Liquid System

2016 ◽  
Author(s):  
Shimpei Saito ◽  
Yuzuru Iwasawa ◽  
Yutaka Abe ◽  
Akiko Kaneko ◽  
Tetsuya Kanagawa ◽  
...  
Keyword(s):  
Weber Number ◽  
Droplet Diameter ◽  
Droplet Formation ◽  
Liquid System ◽  
Immiscible Liquid ◽  
Satellite Droplet ◽  
Breakup Length ◽  
Jet Breakup ◽  
Fundamental Process ◽  
Median Diameter

Mitigative measures against the event of a core disruptive accident (CDA) are of the importance from the viewpoint of safety of a sodium-cooled fast reactor (SFR). If the CDA occurs, the so-called post-accident heat removal must be surely achieved. The present study focuses on the scenario that the molten materials are injected into the lower plenum as jets. The jet breakup behavior during the CDA will be very complicated. Therefore, a specialized study on the fundamental process during the jet breakup is believed to be an effective approach. The aim of this paper is to understand the fundamental process of hydrodynamic interaction of jet breakup and droplet formation Using the immiscible liquid-liquid system, water and silicon oil as the test fluids, visualization via high-speed videography was performed. From the visualization results, the breakup length and droplet diameter were measured by image processing. The experimental data were scaled with ambient Weber number. When the Weber number was smaller than 1, the droplet diameter was close to the nozzle diameter, and distribution of droplet size was not observed. When the Weber number exceeded 1, the breakup length became longer and the generated droplet diameter possessed a distribution with two peaks due to satellite droplet formation. In both cases, the droplet formed at the leading edge of jet. In case that Weber number is around 100, the droplets were formed by entrainment of interfacial wave at jet side. From the mass median diameter data, we can see that the increase of the Weber number caused the decrease of median diameter and the increase of the width of the distribution.

Hydraulic Performance and Jet Breakup Characteristics of the Impact Sprinkler with Circular and Non-circular Nozzles

2019 ◽  
Vol 35 (6) ◽  
pp. 911-924 ◽  
Author(s):  
Yue Jiang ◽  
Hong Li ◽  
Chao Chen ◽  
Lin Hua ◽  
Daming Zhang
Keyword(s):  
High Speed ◽  
Cone Angle ◽  
Hydraulic Performance ◽  
High Speed Photography ◽  
Breakup Process ◽  
Breakup Length ◽  
Jet Breakup ◽  
Circular Jets ◽  
Square Jets ◽  
The Impact

HighlightsThe hydraulic performance of the impact sprinkler with circular and non-circular nozzles were measured.A High-Speed Photography (HSP) technique was employed to extract the jet breakup process of the impact sprinkler.Two index equations of jet characteristic lengths and equivalent diameters of non-circular nozzles were fitted. Abstract. An experiment was carried out to investigate the hydraulic performance of an impact sprinkler by using circular and non-circular nozzles. A High-Speed Photography (HSP) technique was employed to extract the breakup process and flow behavior of low-intermediate pressure water jets issued from the different types of orifices. These orifices were selected by the principle of equal flowrate with the same pressure. Moreover, two characteristic lengths: the jet breakup length and the initial amplitude of surface wave were measured. It was found that the sprinkler with circular nozzles produced the largest radius of throw followed by square nozzles and regular triangular nozzles when the cone angle of nozzle and pressure were unchanged, while the sprinkler with regular triangular nozzle had the best variation trend of water distribution and combination uniformity coefficient. Regular triangular jets exhibited a higher degree in breakup and the shortest breakup length compared with the square jets and the circular jets. The initial amplitudes of surface waves of regular triangular jets were larger than the square jets and the circular jets with the same cone angle. Two index equations of jet characteristic lengths and equivalent diameters of both circular and non-circular orifices were fitted with a relative error of less than 10%, which means the fitting formulas were accurate. Keywords: Breakup length, Fitting formula, Hydraulic performance, Initial amplitude, Non-circular jets.

scholarly journals Breakup of the Water Sheet Formed by Two Liquid Impinging Jets

2019 ◽  
Vol 2019 ◽  
pp. 1-8
Author(s):  
Yakang Xia ◽  
Lyes Khezzar ◽  
Shrinivas Bojanampati ◽  
Arman Molki
Keyword(s):  
Weber Number ◽  
Reynolds Numbers ◽  
Impinging Jets ◽  
Liquid Jets ◽  
Liquid Jet ◽  
Impingement Angle ◽  
Number Range ◽  
Breakup Length ◽  
Sheet Breakup ◽  
Visualization Experiments

Flow visualization experiments are carried out to study the flow regimes and breakup length of the water sheet generated by two impinging liquid jets from an atomizer made of two identical tubes 0.686 mm in diameter. These experiments cover liquid jet Reynolds numbers based on the pipe diameter in the range of 1541 to 5394. The effects of the jet velocities and impingement angle between the two jets on the breakup performance are studied. Four spray patterns are recognized, which are presheet formation, smooth sheet, ruffled sheet, and open-rim sheet regimes. Water sheet breakup length is found to be consistent with previous experimental and theoretical results in the lower Weber number (based on water jet diameter and velocity) range. In the relatively high Weber number range, the breakup length tends to a constant value with increasing Weber number, and some discrepancies between experimental and theoretical predictions do exist. Measured water sheet area increases with increasing liquid jet Reynolds numbers and impingement angle within the range of the current study.

Comparative study on interfacial oscillations of rectangular and elliptical liquid jets

2020 ◽  
Vol 234 (7) ◽  
pp. 1272-1286 ◽  
Author(s):  
Amin Jaberi ◽  
Mehran Tadjfar
Keyword(s):  
Aspect Ratio ◽  
Weber Number ◽  
High Speed ◽  
Nozzle Geometry ◽  
Liquid Jets ◽  
High Speed Photography ◽  
Aspect Ratios ◽  
Water Jets ◽  
Switching Phenomenon ◽  
Axis Switching

The instability characteristics and flow structures of water jets injected from rectangular and elliptical nozzles with aspect ratios varying from 2 to 6 were experimentally studied and compared. Shadowgraph technique was employed for flow visualization, and structures on the liquid jet surface were captured using high speed photography. It was found that disturbances originating from the nozzle geometry initially perturbed the liquid column, and then, at high jet velocities, disturbances generated within the flow dominated the jet surface. It was also found that rectangular nozzles introduced more disturbances into the flow than the elliptical ones. The characteristic parameters of axis-switching phenomenon including wavelength, frequency, and amplitude were measured and compared. Axis-switching wavelength was found to increase linearly with Weber number. Also, the wavelengths of rectangular jets were longer than the elliptical jets. Further, the frequency of axis-switching was shown to be reduced with increase of both Weber number and aspect ratio. It was observed that the axis-switching amplitude increased monotonically, reached a peak, and then decreased gradually. It was also found that the axis-switching amplitude varied with Weber number. At lower values of Weber number, the rectangular nozzles had higher amplitude than the elliptical nozzles. However, at higher values of Weber number, this relation was reversed, and the elliptical nozzles had the higher axis-switching amplitudes. This reversal Weber number decreased with the orifice aspect ratio. The reversal Weber number for aspect ratio of 4 was about 289, and it had decreased to 144 for the aspect ratio of 6.

Experimental Investigation of Liquid Jet Breakup in a Cross Flow of a Swirling Air Stream

2014 ◽  
Vol 136 (6) ◽  
Author(s):  
Tushar Sikroria ◽  
Abhijit Kushari ◽  
Saadat Syed ◽  
Jeffery A. Lovett
Keyword(s):  
Experimental Investigation ◽  
Momentum Flux ◽  
High Speed ◽  
Cross Flow ◽  
Flux Ratio ◽  
Liquid Jet ◽  
Breakup Process ◽  
Breakup Length ◽  
Jet Breakup ◽  
Penetration Behavior

This paper presents the results of an experimental investigation of liquid jet breakup in a cross flow of air under the influence of swirl (swirl numbers 0 and 0.2) at a fixed air flow Mach number 0.12 (typical gas turbine conditions). The experiments have been conducted for various liquid to air momentum flux ratios (q) in the range of 1 to 25. High speed (@ 500 fps) images of the jet breakup process are captured and those images are processed using matlab to obtain the variation of breakup length and penetration height with momentum flux ratio. Using the high speed images, an attempt has been made to understand the physics of the jet breakup process by identification of breakup modes—bag breakup, column breakup, shear breakup, and surface breakup. The results show unique breakup and penetration behavior which departs from the continuous correlations typically used. Furthermore, the images show a substantial spatial fluctuation of the emerging jet resulting in a wavy nature related to effects of instability waves. The results with 15 deg swirl show reduced breakup length and penetration related to the nonuniform distribution of velocity that offers enhanced fuel atomization in swirling fuel nozzles.

Study on some Aspects of Breakup Characteristics of Power-Law Fluid with Impinging Jets Based on Mechanics Properties

2012 ◽  
Vol 625 ◽  
pp. 57-60
Author(s):  
En Dong Wang ◽  
Yan Yin ◽  
Qing Du
Keyword(s):  
Power Law ◽  
High Speed ◽  
Wave Length ◽  
Impinging Jets ◽  
Liquid Sheet ◽  
Liquid Jets ◽  
Power Law Fluid ◽  
Round Jets ◽  
Breakup Length ◽  
Jet Velocity

Shear-thinning power-law fluid is a kind of non-Newtonian fluid in which the viscosity is a function of shear rate. Impinging jets system is used to study the breakup characteristics of power-law liquid sheets formed by two symmetrical round jets in this study. High quality images are obtained from the experiment with a high speed camera and breakup length is extracted from the images. Closed-rim sheet, web-like sheet and ligaments sheet are observed with the increase of jet velocity. A series of images show that the wave length on the surface of sheets tends to decline as the jet velocity increases. At a low We number, the breakup length increases with an increasing We number. However, it first increases and then decreases when the liquid sheet breaks up at a high We number. The liquid jets with larger diameter collide to each other and lead to a liquid sheet with a smaller breakup length.

Computational Analysis on Primary Breakup and Deformation of Kerosene Jet in Subsonic Cross Flow Using VOF Method

2017 ◽  
Author(s):  
Muthuselvan Govindaraj ◽  
Muralidhara Halebidu Suryanarayanarao ◽  
Prateekkumar Kotegar ◽  
Sonali Gupta ◽  
Sanjay Shankar ◽  
...  
Keyword(s):  
Weber Number ◽  
Momentum Flux ◽  
Computational Analysis ◽  
Cross Flow ◽  
Flux Ratio ◽  
Experimental Results ◽  
Liquid Jet ◽  
Computational Domain ◽  
Breakup Process ◽  
Primary Breakup

The main objective of this computational analysis is to investigate the effect of increase in Weber number at constant momentum flux ratio on the primary breakup process and deformation of kerosene jet in cross stream air flow. Unsteady computational analysis with VOF approach is carried out to simulate the two phase flow at three different cross flow Weber number conditions (150, 350 and 400) at constant momentum flux ratio of 17. Since the results of VOF technique is highly sensitive to the size and distribution of grid, grid optimization process is carried out, with both structured and unstructured forms of the grid. Since the structured grid with number of elements 17,96,181 displayed better matching with experimental results of upper trajectory of kerosene jet; this grid is used to investigate the effect of turbulence model and Weber number on the windward trajectory of kerosene jet in cross flow air stream. Initially to evaluate the results of computational analysis; simulations are carried out with larger computational domain (with number of elements 17,96,181). Windward trajectory of computational analysis is compared with experimental results of upper trajectory predicted using image processing technique and reasonable overall matching is observed. To investigate the primary breakup process and deformation of liquid jet at three different increasing Weber number conditions, simulations are carried out with smaller computational domain with higher mesh density with number of elements 33,96,146. The computational technique used in the present analysis exactly captures the modes of breakup observed from experimental results at different Weber number operating conditions. To characterize the deformation of liquid jet at different Weber number conditions; near-field trajectory, cross stream dimension and wave length of liquid jet are quantified at different instants of time. With increase in Weber number, decrease in penetration of liquid jet along transverse direction and more bending of liquid jet along flow direction is observed. From the velocity profile along transverse direction of three different conditions, stronger shearing of liquid film is observed in higher Weber number conditions.

Experiments on the Injection of Elliptical Liquid Jets Into a Low Speed Airflow

2018 ◽  
Author(s):  
Yosef Rezaei ◽  
Mehran Tadjfar
Keyword(s):  
Experimental Investigation ◽  
Weber Number ◽  
Momentum Flux ◽  
High Speed ◽  
Flux Ratio ◽  
Major Axis ◽  
Liquid Jets ◽  
Liquid Jet ◽  
High Speed Camera ◽  
Subsonic Crossflow

An experimental investigation was performed to study the physics of liquid jets injected into a low subsonic crossflow. The jets are issued from elliptical and circular injectors with equivalent exit area. The liquid jet was visualized using shadowgraph technique and a high speed camera was used to record the instantaneous status of the jet. The liquid / air momentum flux ratio and air Weber number were varied to examine their effects on different parameters of the flow like liquid jet column trajectory, breakup point and breakup regimes. The major axis of the elliptical nozzle was aligned parallel and perpendicular to the air crossflow direction. Two different breakup modes were observed, column breakup and bag breakup. Based on the obtained results some characteristics of injected liquid jets into the air crossflow such as penetration depth and the trajectory of liquid jet were affected by changing the nozzle exit shape.

scholarly journals Simulation of Elliptical Liquid Jet Primary Breakup In Supersonic Crossflow

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Yao-zhi Zhou ◽  
Feng Xiao ◽  
Qing-lian Li ◽  
Chen-yang Li
Keyword(s):  
Aspect Ratio ◽  
Penetration Depth ◽  
Horseshoe Vortex ◽  
Liquid Jets ◽  
Liquid Jet ◽  
Breakup Length ◽  
Aspect Ratios ◽  
Primary Breakup ◽  
Elliptical Jet ◽  
Maximum Spreading

The study of elliptical liquid jets in supersonic flow in a Mach 2.0 is performed numerically. The primary breakup process of the elliptical liquid jet is simulated for a Weber number 223, liquid/gas flux momentum 4.0. The aspect ratios of elliptical geometries are set to be 0.25, 0.5, 1, 2, and 5. The results show a remarkable difference in liquid jet disintegration morphology at different aspect ratios. Under supersonic crossflow conditions, the elliptical liquid jet shows more breakup characteristics than the round liquid jet. As the aspect ratio grows, the penetration depth decreases. The elliptical liquid jet with AR=0.25 has the largest penetration depth in all cases. Moreover, the round jet has a maximum spreading angle of 50.2°. The changing trends of the column breakup length both x direction and y direction are similar. The elliptical jet at a lower aspect ratio has a shorter breakup length due to the narrower windward area. The liquid jet has a pair of larger horseshoe vortex structure and a wider wake region at a higher aspect ratio. Two pairs of reversal vortex pairs with obvious characteristics can be observed in all the simulations.

Pulsation in Bag Breakup of Round Liquid Jets in Crossflow

2014 ◽  
Vol 1070-1072 ◽  
pp. 1945-1950
Author(s):  
Pei Feng Liu ◽  
Yong Huang ◽  
Zhi Lin Liu ◽  
Lei Sun
Keyword(s):  
Momentum Flux ◽  
High Speed ◽  
Gas Flow ◽  
Tap Water ◽  
Flux Ratio ◽  
Liquid Jets ◽  
High Speed Camera ◽  
Breakup Process ◽  
Test Liquid ◽  
Momentum Flux Ratio

An experiment was conducted to investigate bag breakup process of round liquid jets in crossflow. The objective of this study is to research pulsation law. Specifically, this study measures the onset position of bag, the breakup position of bag, the breakup position of the jet. High-speed camera was used to observe the formation and breakup of bags. The diameter of the nozzle used in the experiment was 0.5mm, 0.8mm, 1mm. The test liquid was tap water. Wea number covers the range of 6~30, and liquid-to-air momentum flux ratio varied from 22 to 211. Present results indicate that in the direction perpendicular to the gas flow, the dimensionless pulsating amount of the onset point of bags (yonset/d) is linear to q, while the dimensionless pulsating amount of breakup point of bags (ybag/d) and the dimensionless pulsating amount of breakup point of the jet (yjet/d) is linear to ln (q). The dimensionless pulsating amount of these points in the direction of gas flow is irregular.

Sign in / Sign up

Export Citation Format

Share Document