scholarly journals Breakup of the Water Sheet Formed by Two Liquid Impinging Jets

2019 ◽  
Vol 2019 ◽  
pp. 1-8
Author(s):  
Yakang Xia ◽  
Lyes Khezzar ◽  
Shrinivas Bojanampati ◽  
Arman Molki
Keyword(s):  
Weber Number ◽  
Reynolds Numbers ◽  
Impinging Jets ◽  
Liquid Jets ◽  
Liquid Jet ◽  
Impingement Angle ◽  
Number Range ◽  
Breakup Length ◽  
Sheet Breakup ◽  
Visualization Experiments

Flow visualization experiments are carried out to study the flow regimes and breakup length of the water sheet generated by two impinging liquid jets from an atomizer made of two identical tubes 0.686 mm in diameter. These experiments cover liquid jet Reynolds numbers based on the pipe diameter in the range of 1541 to 5394. The effects of the jet velocities and impingement angle between the two jets on the breakup performance are studied. Four spray patterns are recognized, which are presheet formation, smooth sheet, ruffled sheet, and open-rim sheet regimes. Water sheet breakup length is found to be consistent with previous experimental and theoretical results in the lower Weber number (based on water jet diameter and velocity) range. In the relatively high Weber number range, the breakup length tends to a constant value with increasing Weber number, and some discrepancies between experimental and theoretical predictions do exist. Measured water sheet area increases with increasing liquid jet Reynolds numbers and impingement angle within the range of the current study.

A non-linear model for impinging jets atomization

2008 ◽  
Vol 222 (2) ◽  
pp. 213-224 ◽  
Author(s):  
E A Ibrahim ◽  
B E Outland
Keyword(s):  
Linear Model ◽  
Weber Number ◽  
Drop Size ◽  
Impinging Jets ◽  
Liquid Sheet ◽  
Linear Perturbation ◽  
Breakup Length ◽  
Half Wavelength ◽  
Non Linear ◽  
Sheet Breakup

The problem considered is predicting the characteristics of the spray produced by atomization of an attenuating liquid sheet formed by the impingement of two liquid jets of equal diameters and momenta. A second-order non-linear perturbation analysis is employed to model the evolution of harmonic instability waves that lead to sheet distortion and fragmentation. The onset of atomization occurs when the uneven surface modulations of the thinning sheet bring its upper and lower interfaces in contact. It is found that the sheet is torn into ligaments at each half wavelength. The instability of the ligaments causes their eventual disintegration into drops. The results indicate that sheet breakup length, time, and resultant drop size decrease as Weber number is increased. A higher Weber number induces a greater sheet breakup thickness. The breakup length, thickness, time, and drop size are diminished at larger impingement angles. The theoretical predictions of the present non-linear model are in good agreement with available experimental data and empirical correlations for sheet breakup length and drop size.

Dynamics of Liquid Sheet Breakup in Splash Plate Atomization

2017 ◽  
Vol 140 (1) ◽  
Author(s):  
G. Thunivumani ◽  
Hrishikesh Gadgil
Keyword(s):  
Solid Surface ◽  
Weber Number ◽  
Jet Impingement ◽  
Liquid Sheet ◽  
Force Balance ◽  
Impingement Angle ◽  
Wide Range ◽  
Perforated Sheet ◽  
Sheet Breakup ◽  
Regime Map

An experimental study was conducted to investigate the breakup of a liquid sheet produced by oblique impingement of a liquid jet on a plane solid surface. Experiments are carried out over a wide range of jet Weber number (80–6300) and various jet impingement angles (30 deg, 45 deg, and 60 deg) are employed to study the sheet dynamics. The breakup of a liquid sheet takes place in three modes, closed rim, open rim, and perforated sheet, depending upon the Weber number. The transitions across the modes are also influenced by the impingement angle with the transition Weber number reducing with increase in impingement angle. A modified regime map is proposed to illustrate the role of impingement angle in breakup transitions. A theoretical model based on force balance at the sheet edge is developed to predict the sheet parameters by taking the shear interaction between the sheet and the solid surface into account. The sheet shape predicted by the model fairly matches with the experimentally measured sheet shape. The breakup length and width of the sheet are measured and comparisons with the model predictions show good agreement in closed rim mode of breakup.

Study on some Aspects of Breakup Characteristics of Power-Law Fluid with Impinging Jets Based on Mechanics Properties

2012 ◽  
Vol 625 ◽  
pp. 57-60
Author(s):  
En Dong Wang ◽  
Yan Yin ◽  
Qing Du
Keyword(s):  
Power Law ◽  
High Speed ◽  
Wave Length ◽  
Impinging Jets ◽  
Liquid Sheet ◽  
Liquid Jets ◽  
Power Law Fluid ◽  
Round Jets ◽  
Breakup Length ◽  
Jet Velocity

Shear-thinning power-law fluid is a kind of non-Newtonian fluid in which the viscosity is a function of shear rate. Impinging jets system is used to study the breakup characteristics of power-law liquid sheets formed by two symmetrical round jets in this study. High quality images are obtained from the experiment with a high speed camera and breakup length is extracted from the images. Closed-rim sheet, web-like sheet and ligaments sheet are observed with the increase of jet velocity. A series of images show that the wave length on the surface of sheets tends to decline as the jet velocity increases. At a low We number, the breakup length increases with an increasing We number. However, it first increases and then decreases when the liquid sheet breaks up at a high We number. The liquid jets with larger diameter collide to each other and lead to a liquid sheet with a smaller breakup length.

Experiments on the Injection of Elliptical Liquid Jets Into a Low Speed Airflow

2018 ◽  
Author(s):  
Yosef Rezaei ◽  
Mehran Tadjfar
Keyword(s):  
Experimental Investigation ◽  
Weber Number ◽  
Momentum Flux ◽  
High Speed ◽  
Flux Ratio ◽  
Major Axis ◽  
Liquid Jets ◽  
Liquid Jet ◽  
High Speed Camera ◽  
Subsonic Crossflow

An experimental investigation was performed to study the physics of liquid jets injected into a low subsonic crossflow. The jets are issued from elliptical and circular injectors with equivalent exit area. The liquid jet was visualized using shadowgraph technique and a high speed camera was used to record the instantaneous status of the jet. The liquid / air momentum flux ratio and air Weber number were varied to examine their effects on different parameters of the flow like liquid jet column trajectory, breakup point and breakup regimes. The major axis of the elliptical nozzle was aligned parallel and perpendicular to the air crossflow direction. Two different breakup modes were observed, column breakup and bag breakup. Based on the obtained results some characteristics of injected liquid jets into the air crossflow such as penetration depth and the trajectory of liquid jet were affected by changing the nozzle exit shape.

Numerical Simulation of Breakup of Elliptical Liquid Jet in Still Air

2012 ◽  
Author(s):  
Ehsan Farvardin ◽  
Ali Dolatabadi
Keyword(s):  
Numerical Simulation ◽  
Three Dimensional ◽  
Liquid Jets ◽  
Liquid Jet ◽  
Breakup Length ◽  
Aspect Ratios ◽  
Switching Phenomenon ◽  
Dimensional Simulation ◽  
Axis Switching ◽  
Recent Experimental Work

Numerical simulation of liquid jets ejecting from a set of elliptical jets with different aspect ratios between 1 (circular) to 3.85 is performed for several Weber numbers ranging 15 to 330. The axis-switching phenomenon and breakup length of the jets are characterized by means of a Volume of Fluid (VOF) method together with a dynamic mesh refinement model. This three dimensional simulation is compared with a recent experimental work and the results agree well. It is concluded that at Weber numbers less than 100, the breakup length of the liquid jet increases, reaches a peak and then decreases suddenly.

scholarly journals Simulation of Elliptical Liquid Jet Primary Breakup In Supersonic Crossflow

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Yao-zhi Zhou ◽  
Feng Xiao ◽  
Qing-lian Li ◽  
Chen-yang Li
Keyword(s):  
Aspect Ratio ◽  
Penetration Depth ◽  
Horseshoe Vortex ◽  
Liquid Jets ◽  
Liquid Jet ◽  
Breakup Length ◽  
Aspect Ratios ◽  
Primary Breakup ◽  
Elliptical Jet ◽  
Maximum Spreading

The study of elliptical liquid jets in supersonic flow in a Mach 2.0 is performed numerically. The primary breakup process of the elliptical liquid jet is simulated for a Weber number 223, liquid/gas flux momentum 4.0. The aspect ratios of elliptical geometries are set to be 0.25, 0.5, 1, 2, and 5. The results show a remarkable difference in liquid jet disintegration morphology at different aspect ratios. Under supersonic crossflow conditions, the elliptical liquid jet shows more breakup characteristics than the round liquid jet. As the aspect ratio grows, the penetration depth decreases. The elliptical liquid jet with AR=0.25 has the largest penetration depth in all cases. Moreover, the round jet has a maximum spreading angle of 50.2°. The changing trends of the column breakup length both x direction and y direction are similar. The elliptical jet at a lower aspect ratio has a shorter breakup length due to the narrower windward area. The liquid jet has a pair of larger horseshoe vortex structure and a wider wake region at a higher aspect ratio. Two pairs of reversal vortex pairs with obvious characteristics can be observed in all the simulations.

On the Breakup Process of Round Liquid Jets in Gaseous Crossflows at Low Weber Number

2013 ◽  
Author(s):  
Shao-lin Wang ◽  
Yong Huang ◽  
Fang Wang ◽  
Zhi-lin Liu ◽  
Lei Liu
Keyword(s):  
Weber Number ◽  
High Speed ◽  
Droplet Diameter ◽  
Liquid Jets ◽  
Breakup Process ◽  
Ohnesorge Number ◽  
Propulsion Systems ◽  
Momentum Ratio ◽  
Breakup Length ◽  
Primary Breakup

Liquid jets in cross air flows are widely used and play an important role in propulsion systems, such as ramjet combustors. In this paper, experiments were carried out to investigate the properties of the primary breakup of liquid jets in subsonic transverse airflows at low Weber number. The test ranges included crossflow Weber numbers of 0.5–6.7, liquid-to-gas momentum ratios of 3–120, and Ohnesorge number of 0.0086. Four different injectors with diameter 0.4mm, 0.5mm, 0.6mm and 1mm have been used. A high speed camera was used to observe the jet column breakup process. Results show that the surface wavelength decreases not only with the increase of the gas Weber number but also with the increase of the momentum ratio. The breakup length decreases with the increase of the gas Weber number, in addition to its increase with the increase of the momentum ratio. The droplet diameter decreases with the increase of both the gas Weber number and momentum ratio, although the gas Weber number will dominate the breakup process. The surface wavelength, breakup length, and droplet diameter were also analyzed with to obtain semi-theoretical correlations.

Deformation and Surface Waves Properties of Round Nonturbulent Liquid Jets in Gaseous Crossflow

2005 ◽  
Author(s):  
C.-L. Ng ◽  
K. A. Sallam ◽  
H. M. Metwally ◽  
C. Aalburg
Keyword(s):  
Surface Waves ◽  
Weber Number ◽  
Computational Study ◽  
Density Ratio ◽  
Three Dimensional ◽  
Liquid Jets ◽  
Liquid Jet ◽  
Liquid Viscosity ◽  
Fluent Software ◽  
Wave Properties

A computational study of the deformation and surface wave properties of nonturbulent round liquid jets in gaseous crossflow is described. The objective of the study was to consider effects of liquid viscosity, liquid/gas density ratio, and crossflow Weber number that are representative of practical sprays. Three-dimensional computations of the deformation of round liquid jets in gaseous crossflow were carried out using FLUENT software utilizing its Volume of Fluid (VOF) module. The computations were evaluated satisfactorily based on earlier measurements of the properties of nonturbulent round liquid jets in crossflow (liquid jet deformation and surface waves) and revealed three-dimensional properties of the surface waves that could not be observed by previous measurements that were taken from the side of the jet.

The Breakup Length of Turbulent Liquid Jets

1977 ◽  
Vol 99 (2) ◽  
pp. 414-415 ◽  
Author(s):  
P. Lafrance
Keyword(s):  
Experimental Data ◽  
Statistical Distribution ◽  
Liquid Jets ◽  
Liquid Jet ◽  
Capillary Instability ◽  
Turbulent Fluctuations ◽  
Breakup Length ◽  
Comparison With Experimental Data

A formula for the statistical distribution of the breakup length of a turbulent liquid jet is derived. The formula is based on a model in which random turbulent fluctuations are amplified by capillary instability. A comparison with experimental data is made.

Satellite formation and merging in liquid jet breakup

1991 ◽  
Vol 433 (1888) ◽  
pp. 269-286 ◽  
Keyword(s):  
Weber Number ◽  
High Speed ◽  
Drop Size ◽  
Liquid Jet ◽  
Number Range ◽  
Satellite Formation ◽  
Long Wavelength ◽  
Breakup Mechanism ◽  
Jet Breakup ◽  
New Type

An experimental investigation of the breakup of a liquid jet using high-speed motion pictures has revealed many different breakup mechanisms. The influence of disturbance amplitude and frequency on the breakup mechanism for a Weber number range of 25 to 160 is considered. The jet breakup is grouped into several distinct regions, depending on the disturbance wavelength ( λ ), and the undisturbed jet diameter ( D ). These include the random breakup region for λ/D < 3, short wavelength Rayleigh breakup region for 3 < λ/D < 5.5, medium wavelength Rayleigh breakup region for 5.5 < λ/D < 11, and long wavelength Rayleigh breakup region for λ/D > 11. Except for the random region ( λ/D < 3), all the other regions show repeatable patterns of breakup. The boundaries between some of the distinct patterns are obtained for various Weber numbers and disturbance amplitudes. A new type of satellite merge is also discovered which is referred to as the reflexive merging satellite. Other features of the jet breakup, such as satellite/drop size ratio and breakup times, are also considered in detail.

Sign in / Sign up

Export Citation Format

Share Document