Experimental and Numerical Investigations of Flowpath Profiling on Secondary Flow Losses in a Turbine Control Stage

2013 ◽  
Author(s):  
Nils Moser ◽  
Peter Steinhoff ◽  
Franz Joos
Keyword(s):  
Pressure Distribution ◽  
Secondary Flow ◽  
Guide Vane ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Formation Mechanisms ◽  
Guide Vanes ◽  
Numerical Investigations ◽  
Control Stage ◽  
Wide Range

The numerically and experimentally investigated industrial steam turbine control stage is derived from a real design. Due to the production process and costs of the guide vanes for control stages of steam turbines the flowpath profiling is rotationally symmetric. However the combination of the two-dimensional shroud contour and the flow deflection in the guide vane results in a fully three-dimensional end wall contour having a strong influence on the secondary flow features in the turbine control stage. To obtain an improved profile for the nozzle shroud the reduction of the total pressure loss over the guide vanes is taken as an optimization criterion. The three-dimensional contour generates a diffuser flowpath between the suction and the pressure side of two guide vanes perpendicular to the main flow direction. This diffuser geometry affects the pressure distribution over the guide vane and therefore the formation mechanisms of secondary flows. For the experimental and numerical investigations a baseline shroud design and two additional profiled contours are analyzed in detail. The control stage test rig is operated with air and is capable to represent a wide range of operating conditions. The measurements show a considerable increase of the stage efficiency and power output. The effect of the flowpath profiling on the pressure distribution over the guide vane is clearly proved.

Measurement of Unsteady Flow in Pump-Turbine for Hydropower Using PIV Method

2009 ◽  
Author(s):  
Nobuhiko Fukuda ◽  
Satoshi Someya ◽  
Koji Okamoto
Keyword(s):  
Rotational Speed ◽  
Velocity Measurement ◽  
Numerical Procedure ◽  
Hydraulic Turbine ◽  
Operating Conditions ◽  
High Time ◽  
Pump Turbine ◽  
Guide Vanes ◽  
Runner Blade ◽  
Wide Range

It is thought that the pressure fluctuation can occur due to the interaction between flow through guide vanes and flow into runner blades, resulting in a vibration of turbine and a blade cracking, in a hydraulic turbine operated in a wide range for flexible power demand. High accurate velocity measurement with high time/spatial resolution can help to clarify the mechanism of the interaction and to provide good experimental data for the validation of numerical procedure. So the aim of present study is to estimate the unstable velocity field quantitatively in the area between guide vanes and runner blades, using high time-resolved particle image velocimetry (PIV). Two types of velocity measurements were carried out, i.e., phase-locked measurement and high time sequential velocity measurement, in a pump-turbine model with 20 guide vanes and 6 runner blades. The characteristic of the flow field varied corresponding to the operating conditions such as flow rate and rotational speed. Opening angles of guide vanes were kept uniform. A clockwise vortex was generated at inside of the runner blade under smaller rotational speed. A counterclockwise vortex was separated at the backside of the runner blade under higher rotational speed. At any operating conditions, the velocity between guide vanes and runner blades oscillated periodically at the blade passing frequency.

Experimental Studies of Leading Edge Contouring Influence on Secondary Losses in Transonic Turbines

2012 ◽  
Author(s):  
Ranjan Saha ◽  
Jens Fridh ◽  
Torsten Fransson ◽  
Boris I. Mamaev ◽  
Mats Annerfeldt
Keyword(s):  
Gas Turbine ◽  
Guide Vane ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Leading Edge ◽  
Secondary Flows ◽  
Noticeable Effect ◽  
Flow Angle ◽  
Wide Range ◽  
Contour Plots

An experimental study of the hub leading edge contouring using fillets is performed in an annular sector cascade to observe the influence of secondary flows and aerodynamic losses. The investigated vane is a three dimensional gas turbine guide vane (geometrically similar) with a mid-span aspect ratio of 0.46. The measurements are carried out on the leading edge fillet and baseline cases using pneumatic probes. Significant precautions have been taken to increase the accuracy of the measurements. The investigations are performed for a wide range of operating exit Mach numbers from 0.5 to 0.9 at a design inlet flow angle of 90°. Data presented include the loading, fields of total pressures, exit flow angles, radial flow angles, as well as profile and secondary losses. The vane has a small profile loss of approximately 2.5% and secondary loss of about 1.1%. Contour plots of vorticity distributions and velocity vectors indicate there is a small influence of the vortex-structure in endwall regions when the leading edge fillet is used. Compared to the baseline case the loss for the filleted case is lower up to 13% of span and higher from 13% to 20% of the span for a reference condition with Mach no. of 0.9. For the filleted case, there is a small increase of turning up to 15% of the span and then a small decrease up to 35% of the span. Hence, there are no significant influences on the losses and turning for the filleted case. Results lead to the conclusion that one cannot expect a noticeable effect of leading edge contouring on the aerodynamic efficiency for the investigated 1st stage vane of a modern gas turbine.

The Extension of a Solution-Adaptive Three-Dimensional Navier–Stokes Solver Toward Geometries of Arbitrary Complexity

1993 ◽  
Vol 115 (2) ◽  
pp. 283-295 ◽  
Author(s):  
W. N. Dawes
Keyword(s):  
Guide Vane ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Centrifugal Impeller ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Wide Range ◽  
Nozzle Guide Vane ◽  
Recent Developments ◽  
Nozzle Guide

This paper describes recent developments to a three-dimensional, unstructured mesh, solution-adaptive Navier–Stokes solver. By adopting a simple, pragmatic but systematic approach to mesh generation, the range of simulations that can be attempted is extended toward arbitrary geometries. The combined benefits of the approach result in a powerful analytical ability. Solutions for a wide range of flows are presented, including a transonic compressor rotor, a centrifugal impeller, a steam turbine nozzle guide vane with casing extraction belt, the internal coolant passage of a radial inflow turbine, and a turbine disk cavity flow.

Hydraulic Characteristics of the New Type Bulb Turbine With Micro-Head

2013 ◽  
Author(s):  
Lingyu Li ◽  
Yuan Zheng ◽  
Daqing Zhou ◽  
Zihao Mi
Keyword(s):  
Numerical Simulation ◽  
Cfd Simulation ◽  
Guide Vane ◽  
Three Dimensional ◽  
Flow Distribution ◽  
Three Dimensions ◽  
Guide Vanes ◽  
Runner Blade ◽  
Cfd Method ◽  
Bulb Turbine

The head of low-head hydropower stations is generally higher than 2.5m in the world, while micro-head hydropower resources which head is less than 2.5m are also very rich. In the paper, three-dimensional CFD method has been used to simulate flow passage of the micro-head bulb turbine. The design head and unit flow of the turbine was 1m and 3m3/s respectively. With the numerical simulation, the bulb turbine is researched by analyzing external characteristics of the bulb turbine, flow distribution before the runner, pressure distribution of the runner blade surface, and flow distribution of the outlet conduit under three different schemes. The turbine in second scheme was test by manufactured into a physical model. According to the results of numerical simulation and model test, bulb turbine with no guide vane in second scheme has simpler structure, lower cost, and better flow capacity than first scheme, which has traditional multi-guide vanes. Meanwhile, efficiency of second scheme has just little decrease. The results of three dimensions CFD simulation and test results agree well in second scheme, and higher efficiency is up to 77% which has a wider area with the head of 1m. The curved supports in third scheme are combined guide vanes to the fixed supports based on 2nd scheme. By the water circulations flowing along the curved supports which improve energy transformation ability of the runner, the efficiency of the turbine in third scheme is up to 82.6%. Third scheme, which has simpler structure and best performance, is appropriate for the development and utilization of micro-head hydropower resources in plains and oceans.

The Effect of Reynolds Number and Velocity Distribution on LP Turbine Cascade Performance

1986 ◽  
Author(s):  
D. J. Patterson ◽  
M. Hoeger
Keyword(s):  
Reynolds Number ◽  
Pressure Distribution ◽  
Guide Vane ◽  
Flow Visualisation ◽  
Suction Surface ◽  
Trailing Edge ◽  
Wide Range ◽  
Oil Flow ◽  
Low Reynolds ◽  
Lp Turbine

Because of the laminar boundary-layer’s inability to withstand moderate adverse pressure gradients without separating, profile losses in LP turbines operating at low Reynolds numbers can be high. The choice of design pressure distribution for the blading is thus of great importance. Three sub-sonic LP turbine nozzle-guide-vane cascade profiles have been tested over a wide range of incidence, Mach number and Reynolds number. The three profiles are of low, medium and high deflection and, as such, display significantly different pressure distributions. The tests include detailed boundary-layer traverses, trailing-edge base-pressure monitoring and oil-flow visualisation. It is shown that the loss variation with Reynolds number is a function of pressure distribution and that the trailing-edge loss component is dominant at low Reynolds number. The importance of achieving late flow transition — rather than separation — in the suction-surface trailing-edge region is stressed. The paper concludes by remarking on the advantages and practical implications of each loading design.

scholarly journals Improvement of Pump Performance at Off-Design Conditions

1985 ◽  
Author(s):  
J. Paulon ◽  
C. Fradin ◽  
J. Poulain
Keyword(s):  
Experimental Study ◽  
Flow Field ◽  
Mass Flow ◽  
Flow Characteristic ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Pump Performance ◽  
Wide Range ◽  
Mass Flows ◽  
Design Value

Industrial pumps are generally used in a wide range of operating conditions from almost zero mass flow to mass flows larger than the design value. It has been often noted that the head-mass flow characteristic, at constant speed, presents a negative bump as the mass flow is somewhat smaller than the design mass flows. Flow and mechanical instabilities appear, which are unsafe for the facility. An experimental study has been undertaken in order to analyze and if possible to palliate these difficulties. A detailed flow analyzis has shown strong three dimensional effects and flow separations. From this better knowledge of the flow field, a particular device was designed and a strong attenuation of the negative bump was obtained.

Influence of Pre-History and Leading Edge Contouring on Aero-Performance of a 3D Nozzle Guide Vane

2013 ◽  
Author(s):  
Ranjan Saha ◽  
Boris I. Mamaev ◽  
Jens Fridh ◽  
Björn Laumert ◽  
Torsten H. Fransson
Keyword(s):  
Guide Vane ◽  
Three Dimensional ◽  
Leading Edge ◽  
Stagnation Line ◽  
Wide Range ◽  
Nozzle Guide Vane ◽  
Turbine Vane ◽  
Loss Coefficients ◽  
Exit Mach Number ◽  
Nozzle Guide

Experiments are conducted to investigate the effect of the pre-history in the aerodynamic performance of a three-dimensional nozzle guide vane with a hub leading edge contouring. The performance is determined with two pneumatic probes (5 hole and 3 hole) concentrating mainly on the endwall. The investigated vane is a geometrically similar gas turbine vane for the first stage with a reference exit Mach number of 0.9. Results are compared for the baseline and filleted cases for a wide range of operating exit Mach numbers from 0.5 to 0.9. The presented data includes loading distributions, loss distributions, fields of exit flow angles, velocity vector and vorticity contour, as well as, mass-averaged loss coefficients. The results show an insignificant influence of the leading edge fillet on the performance of the vane. However, the pre-history (inlet condition) affects significantly in the secondary loss. Additionally, an oil visualization technique yields information about the streamlines on the solid vane surface which allows identifying the locations of secondary flow vortices, stagnation line and saddle point.

Mechanical Design and Testing of a 2.5 MW sCO2 Compressor Loop

2021 ◽  
Author(s):  
Stefan D. Cich ◽  
J. Jeffrey Moore ◽  
Chris Kulhanek ◽  
Meera Day Towler ◽  
Jason Mortzheim
Keyword(s):  
High Efficiency ◽  
Mechanical Design ◽  
Guide Vane ◽  
Operating Conditions ◽  
Inlet Guide Vane ◽  
Inlet Temperature ◽  
Design Changes ◽  
Wide Range ◽  
Inlet Conditions ◽  
Design And Testing

Abstract An enabling technology for a successful deployment of the sCO2 close-loop recompression Brayton cycle is the development of a compressor that can maintain high efficiency for a wide range of inlet conditions due to large variation in properties of CO2 operating near its dome. One solution is to develop an internal actuated variable Inlet Guide Vane (IGV) system that can maintain high efficiency in the main and re-compressor with varying inlet temperature. A compressor for this system has recently been manufactured and tested at various operating conditions to determine its compression efficiency. This compressor was developed with funding from the US DOE Apollo program and industry partners. This paper will focus on the design and testing of the main compressor operating near the CO2 dome. It will look at design challenges that went into some of the decisions for rotor and case construction and how that can affect the mechanical and aerodynamic performance of the compressor. This paper will also go into results from testing at the various operating conditions and how the change in density of CO2 affected rotordynamics and overall performance of the machine. Results will be compared to expected performance and how design changes were implanted to properly counter challenges during testing.

A Geometry Generation Framework for Contoured Endwalls

2019 ◽  
Author(s):  
L. E. Wood ◽  
R. R. Jones ◽  
O. J. Pountney ◽  
J. A. Scobie ◽  
D. A. S. Rees ◽  
...  
Keyword(s):  
Secondary Flow ◽  
Three Dimensional ◽  
Aerodynamic Loss ◽  
Construction Methods ◽  
Novel Approach ◽  
Wide Range ◽  
Blade Row ◽  
Flow Features ◽  
Flow Effects ◽  
Geometric Variation

Abstract The mainstream, or primary, flow in a gas turbine annulus is characteristically two-dimensional over the mid-span region of the blading, where the radial flow is almost negligible. Contrastingly, the flow in the endwall and tip regions of the blading is highly three-dimensional, characterised by boundary layer effects, secondary flow features and interaction with cooling flows. Engine designers employ geometric contouring of the endwall region in order to reduce secondary flow effects and subsequently minimise their contribution to aerodynamic loss. Such is the geometric variation of vane and blade profiles — which has become a proprietary art form — the specification of an effective endwall geometry is equally unique to each blade-row. Endwall design methods, which are often directly coupled to aerodynamic optimisers, are widely developed to assist with the generation of contoured surfaces. Most of these construction methods are limited to the blade-row under investigation, while few demonstrate the controllability required to offer a universal platform for endwall design. This paper presents a Geometry Generation Framework (GGF) for the generation of contoured endwalls. The framework employs an adaptable meshing strategy, capable of being applied to any vane or blade, and a versatile function-based approach to defining the endwall shape. The flexibility of this novel approach is demonstrated by recreating a selection of endwalls from the literature, which were selected for their wide-range of contouring approaches.

scholarly journals Cyclic NO2:NOx ratio from a diesel engine undergoing transient load steps

2019 ◽  
Vol 22 (1) ◽  
pp. 284-294 ◽  
Author(s):  
FCP Leach ◽  
MH Davy ◽  
MS Peckham
Keyword(s):  
Diesel Engine ◽  
High Speed ◽  
Exhaust Gas Recirculation ◽  
Operating Conditions ◽  
Formation Mechanisms ◽  
Exhaust Gas ◽  
Work Cycle ◽  
Wide Range ◽  
Gas Recirculation ◽  
Aftertreatment Systems

As the control of real driving emissions continues to increase in importance, the importance of understanding emission formation mechanisms during engine transients similarly increases. Knowledge of the NO2/NOx ratio emitted from a diesel engine is necessary, particularly for ensuring optimum performance of NOx aftertreatment systems. In this work, cycle-to-cycle NO and NOx emissions have been measured using a Cambustion CLD500, and the cyclic NO2/NOx ratio calculated as a high-speed light-duty diesel engine undergoes transient steps in load, while all other engine parameters are held constant across a wide range of operating conditions with and without exhaust gas recirculation. The results show that changes in NO and NOx, and hence NO2/NOx ratio, are instantaneous upon a step change in engine load. NO2/NOx ratios have been observed in line with previously reported results, although at the lightest engine loads and at high levels of exhaust gas recirculation, higher levels of NO2 than have been previously reported in the literature are observed.

Sign in / Sign up

Export Citation Format

Share Document