Optimization of Two and Three Rotor Savonius Wind Turbine

2015 ◽  
Author(s):  
Ahmed M. Baz ◽  
Nabil A. Mahmoud ◽  
Ashraf M. Hamed ◽  
Khaled M. Youssef
Keyword(s):  
Wind Turbine ◽  
Average Power ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Rotor Design ◽  
Aerodynamic Interaction ◽  
Torque Coefficient ◽  
Savonius Wind Turbine ◽  
Improved Performance ◽  
Turbine Design

The present work investigates the performance of Savonius wind turbine using two or three rotors. The new turbine design was found to have higher power coefficient compared with single rotor design. The peak average power coefficient of the three rotors was computed to be 50% higher than that of the single rotor design. The torque coefficient was also higher than that of the single rotor turbine at high tip speed ratio. This improved performance is attributed to the favorable aerodynamic interaction between the rotors which accelerates the flow around the rotors and generates higher turning torque in the direction of rotation for each rotor. The optimized arrangement of rotors showed that the upstream rotor and one downstream rotor should have a similar direction of rotation while the second downstream rotor is rotating in opposite direction.

scholarly journals Effect of Stator Vane on the Performance of the Savonius Wind Turbine

2019 ◽  
Vol 4 (2) ◽  
pp. 159-168
Author(s):  
Yoga Arob Wicaksono
Keyword(s):  
Wind Turbine ◽  
Performance Testing ◽  
Turbine Rotor ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Stator Vane ◽  
Torque Coefficient ◽  
Savonius Wind Turbine ◽  
Air Speed ◽  
Turbulent Air Flow

The turbulent air flow conditions in the urban area have a large effect on the performance of Savonius rotor wind turbines. To overcome this problem, a new design of the stator vane needs to be made. the stator vane has the ability to direct wind to the turbine rotor and increase air speed by utilizing throttling effects. Thus, the performance of the Savonius wind turbine can increase. In this study, the Savonius type vertical wind turbine is configured with three stator vane designs that have slope angles: 60o, and 70o. Performance testing is carried out at angles: 0o, 30o, and 60o towards the midpoint of the stator vane to find the direction of direction coming from the best wind on each stator vane design. All configurations are analyzed using an experimental wind tunnel open testing scheme with a wind speed range of 3-5 m/s. The parameters produced from the experiment include: power coefficient (Cp), torque coefficient (Ct) and Tip Speed ​​Ratio (TSR). The results showed that the stator vane with 60o inclination angle was able to increase Cp 35.66% in the 60o incoming wind direction.

scholarly journals Performance assessment and optimization of a helical Savonius wind turbine by modifying the Bach’s section

2021 ◽  
Vol 3 (8) ◽  
Author(s):  
M. Niyat Zadeh ◽  
M. Pourfallah ◽  
S. Safari Sabet ◽  
M. Gholinia ◽  
S. Mouloodi ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Performance Assessment ◽  
Turbulent Flows ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Tip Speed Ratio ◽  
Basic Model ◽  
Turbine Performance ◽  
Primary Model ◽  
Savonius Wind Turbine

AbstractIn this paper, we attempted to measure the effect of Bach’s section, which presents a high-power coefficient in the standard Savonius model, on the performance of the helical Savonius wind turbine, by observing the parameters affecting turbine performance. Assessment methods based on the tip speed ratio, torque variation, flow field characterizations, and the power coefficient are performed. The present issue was stimulated using the turbulence model SST (k- ω) at 6, 8, and 10 m/s wind flow velocities via COMSOL software. Numerical simulation was validated employing previous articles. Outputs demonstrate that Bach-primary and Bach-developed wind turbine models have less flow separation at the spoke-end than the simple helical Savonius model, ultimately improving wind turbines’ total performance and reducing spoke-dynamic loads. Compared with the basic model, the Bach-developed model shows an 18.3% performance improvement in the maximum power coefficient. Bach’s primary model also offers a 12.4% increase in power production than the initial model’s best performance. Furthermore, the results indicate that changing the geometric parameters of the Bach model at high velocities (in turbulent flows) does not significantly affect improving performance.

scholarly journals A Dynamic Rotor Vertical-Axis Wind Turbine with a Blade Transitioning Capability

Energies ◽  
2019 ◽  
Vol 12 (8) ◽  
pp. 1446 ◽  
Author(s):  
Elie Antar ◽  
Amne El Cheikh ◽  
Michel Elkhoury
Keyword(s):  
Wind Turbine ◽  
Average Power ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Optimized Design ◽  
Detached Eddy Simulation ◽  
Vertical Axis Wind Turbine ◽  
Eddy Simulation ◽  
Delayed Detached Eddy Simulation

This work presents an optimized design of a dynamic rotor vertical-axis wind turbine (DR VAWT) which maximizes the operational tip-speed ratio (TSR) range and the average power coefficient (Cp) value while maintaining a low cut-in wind velocity. The DR VAWT is capable of mimicking a Savonius rotor during the start-up phase and transitioning into a Darrieus one with increasing rotor radius at higher TSRs. The design exploits the fact that with increasing rotor radius, the TSR value increases, where the peak power coefficient is attained. A 2.5D improved delayed detached eddy simulation (IDDES) approach was adopted in order to optimize the dynamic rotor design, where results showed that the generated blades’ trajectories can be readily replicated by simple mechanisms in reality. A thorough sensitivity analysis was conducted on the generated optimized blades’ trajectories, where results showed that they were insensitive to values of the Reynolds number. The performance of the DR VAWT turbine with its blades following different trajectories was contrasted with the optimized turbine, where the influence of the blade pitch angle was highlighted. Moreover, a cross comparison between the performance of the proposed design and that of the hybrid Savonius–Darrieus one found in the literature was carefully made. Finally, the effect of airfoil thickness on the performance of the optimized DR VAWT was thoroughly analyzed.

scholarly journals STUDI EKSPERIMENTAL PERFORMANSI TURBIN SAVONIUS DI PESISIR PANTAI KABUPATEN DEMAK TERHADAP DAYA LISTRIK YANG DIHASILKAN

2021 ◽  
Vol 14 (1) ◽  
pp. 16
Author(s):  
Wahyu Santoso ◽  
Herman Saputro ◽  
Husin Bugis
Keyword(s):  
Renewable Energy ◽  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Raw Material ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Generator Type ◽  
Wind Potential ◽  
Savonius Wind Turbine

<p><em>Energy from fossil fuels consisting of petroleum, coal, natural gas containing raw material for energy fulfillment in Indonesia is still very central through the use of raw materials from renewable energy is still very low. In Indonesia the potential for renewable energy such as wind energy needs to be optimized. One of the uses of wind energy is through savonius wind turbine as electricity generators. Characteristics of savonius wind turbine with vertical axis rotors which gave a simple shape, and that able to control low speeds. This is in accordance with regions in Indonesi which have low average speeds.         This experimental study, aims to determine the description of wind potential and determine the performance of savonius wind turbines on the coast of Demak regency on the electrical energy produced. Savonius wind turbine used is made of galvalum material in the form of an S type rotor with diameter 1.1 m and height 1.4 m, using pulley transmission system with multiplication ratio 1:6 dan using generator type PMG 200 W. This research uses the method experiment. Data collection in the form of wind speed, humidity, temperature, rotor rotation speed, voltage and electric curret is carried out at 14.30 to 17.30 Western Indonesian Time. Data Analysis in this study uses quantitative descriptive analysis. The result showed the potential of wind on the coast of Demak regency have an average wind speed of 2,02 m/s with a temperature of 31</em><em>,</em><em>34 </em><em><sup>0</sup></em><em>C and humidity of 76,96. And the performance of the installed wind turbine produces the highest power 3.5 watt with an electric power coefficient of 0,181 and tip speed ratio around 1,75. From these result, the potensial of wind with performance savonius turbine can generate electricity used for pond lighting in the village Berahan Kulon Kecamatan Wedung. </em><em></em></p>

Experimental Study of a Pinwheel-Type Wind Turbine

2003 ◽  
Vol 27 (3) ◽  
pp. 227-236 ◽  
Author(s):  
Yasuyuki Nemoto ◽  
Izumi Ushiyama
Keyword(s):  
Experimental Study ◽  
Wind Tunnel ◽  
Wind Turbine ◽  
Optimum Design ◽  
Architectural Design ◽  
Frontal Area ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Tip Speed Ratio ◽  
Torque Coefficient

Pinwheels have been familiar as toys for hundreds of years. Not only do they have an attractive appearance, they can also be fabricated from just one piece of plate. Application is possible, e.g. for education and architectural design. The purpose of this paper is to clarify the characteristics and to determine the optimum design configuration of pinwheel type wind turbines. The authors fabricated the test rotors with various shapes and carried out the experiment in a wind tunnel. As a result, the following facts were obtained: (1) Power coefficient with the traditional 4 blades has, CPmax = 0.17 at λ = 2. (2) High tip speed is obtained by cutting the frontal area of pinwheel. Tip speed ratio at no load can be easily changed from λ = 3 to 6 by changing the cutting area. Maximum power coefficient CPmax = 0.22 was obtained at tip speed ratio λ = 3.5. (3) Increased torque is obtained by cutting the edge area of the pinwheel. Tip speed ratio at no load can be easily changed from λ = 2 to 3, and torque coefficient can be easily changed from CQmax = 0.15 to 0.25, by changing the cut area.

scholarly journals Drag coefficient calculation of modified Myring-Savonius wind turbine with numerical simulations

2020 ◽  
Vol 10 (2) ◽  
pp. 73-84
Author(s):  
Mahmoud Saleh ◽  
Endre Kovács
Keyword(s):  
Drag Coefficient ◽  
Wind Turbine ◽  
Primary Objective ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Energy Potential ◽  
Cross Sectional ◽  
Ansys Fluent ◽  
Tip Speed Ratio ◽  
Savonius Wind Turbine

Nowadays the importance of renewable energy is growing, and the utilization of the low wind energy potential is getting crucial. There are turbines with low and high tip speed ratio. Turbines with low tip speed ratio such as the Savonius wind turbine can generate adequate amount of torque at low wind velocities. These types of turbines are also called drag machines. The geometry of the blade can greatly influence the efficiency of the device. With Computational Fluid Dynamics (CFD) method, several optimizations can be done before the production. In our paper the Savonius wind turbine blade geometry was designed based on the so-called Myring equation. The primary objective of this paper was to investigate the drag coefficient of the force acting on the surface of the blade. Also, the Karman vortex was investigated and the space ratio of that vortex in our simulation was compared to a typical one. The power coefficient of a new Savonius turbine was investigated at different values of top speed ratio (TSR). For the sake of simplicity, a 2D cross-sectional area was investigated in the simulation with ANSYS Fluent 19.2.

scholarly journals Numerical Model Analysis of Myring–Savonius wind turbines

2019 ◽  
Vol 4 (1) ◽  
pp. 180-185
Author(s):  
M. Saleh ◽  
Ferenc Szodrai
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Primary Objective ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Energy Potential ◽  
Cross Sectional ◽  
Tip Speed Ratio ◽  
Savonius Wind Turbine ◽  
Cfd Method

Nowadays the importance of renewable energy is growing, and the utilization of the low wind energy potential is getting crucial. There are turbines with low and high tip speed ratio. Turbines with low tip speed ratio such as the Savonius wind turbine can generate adequate amount of torque at low wind velocities. These types of turbines are also called drag machines. The geometry of the blade can greatly influence the efficiency of the device. With Computational Fluid Dynamics (CFD) method, several optimizations can be done before the production. In our paper the Savonius wind turbine blade geometry was based on the so-called Myring equation. The primary objective of this paper was to increase the power coefficient by modelling the effect of the wind on the turbine blade. For the sake of simplicity, a 2D cross-sectional area was investigated in the simulation with ANSYS CFX 19.1.

scholarly journals Studi Eksperimen Pengaruh Jumlah Sudu Terhadap Kinerja Wind Turbine Crossflow

2021 ◽  
Vol 16 (2) ◽  
pp. 218
Author(s):  
Fahrudin Fahrudin ◽  
Fitri Wahyuni ◽  
Dini Oktavitasari
Keyword(s):  
Wind Turbine ◽  
Alternative Energy ◽  
Wind Tunnel Test ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Test Scheme ◽  
Vertical Axis Wind Turbine ◽  
Tip Speed Ratio ◽  
Torque Coefficient

<p>Wind is an alternative energy that is environmentally friendly and sustainable. Therefore, we need a type of wind turbine that can receive wind from all directions. The crossflow type vertical axis wind turbine has a high torque coefficient at a low tip speed ratio. The purpose of this study was to determine the effect of the number of blades on the performance of the vertical axis crossflow wind turbine. The experimental test was carried out by varying the number of blades. The configuration is analyzed using the experimental wind tunnel test scheme which has been modified in the section test section. The results showed that the number of blades 16 has a power coefficient ( ) = 0.23 tip speed ratio (TSR) = 0.42 at a wind speed of 4 m / s.</p><p><strong><br /></strong></p>

scholarly journals Effect of Savonius blade height on the performance of a hybrid Darrieus-Savonius wind turbine

2019 ◽  
Vol 13 (4) ◽  
pp. 5832-5847
Author(s):  
Dewi Puspitasari ◽  
Kaprawi Sahim
Keyword(s):  
Wind Turbine ◽  
Important Variable ◽  
Power Coefficient ◽  
Height Ratio ◽  
Blade Height ◽  
Subsonic Wind Tunnel ◽  
Turbine Performance ◽  
Torque Coefficient ◽  
Savonius Wind Turbine ◽  
Turbine Construction

A vertical hybrid turbine commonly consists of a Darrieus and Savonius rotor where the Savonius is inside Darrieus turbine. This paper describes the experimental study of hybrid Darrieus-Savonius wind turbines by variation in Savonius blade height. In this case, the effect of the blade height of the Savonius blade was studied experimentally in a subsonic wind tunnel. The effect of the height of a Savonius blade relative to that of Darrieus called blade height ratios δ was investigated to know the hybrid turbine performance. The performance is represented by power and torque coefficient. The result shows that the hybrid turbine with height ratio greater than unity δ = 1.4 gives the highest power CP = 0.20 and torque coefficient CT = 0.129. It is investigated that the torque and the power coefficient have a higher value than that of Darrieus turbine, in which the increase in power and torque coefficient are 48% and 29%, respectively. This hybrid wind turbine with a blade height ratio greater than unity can be considered as an important variable in the wind turbine construction.

Numerical Modelling of Savonius Wind Turbine With Downstream Baffle

2015 ◽  
Author(s):  
Ahmed M. El Baz ◽  
Nabil A. Mahmoud ◽  
Ashraf M. Hamed ◽  
Ahmed M. El Kholy
Keyword(s):  
Wind Turbine ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Dynamics Model ◽  
Small Power ◽  
Turbine Performance ◽  
Savonius Wind Turbine ◽  
Driving Torque

The application of small power wind turbines has been widely spreading over the last decade. The vertical axis wind turbine type is one class which is very attractive in this respect. However, due to its lower performance, it has not been extensively used in such application. The objective of the present paper is to investigate methods of Savonius turbine performance improvement. It is suggested to use a downstream baffle to achieve this goal. The baffle position, length and inclination angle are optimized using 2D Computational Fluid Dynamics model. The model is initially validated by comparison to experimental data reported for the Savonius turbine without baffle. The results show that 40–50% improvement in turbine performance can be obtained by using the optimum baffle design, compared to the turbine performance without baffle. The baffle effect is analyzed and results show that its major role is to reduce the pressure on the backside of the advancing blade. This effect enhances the positive driving torque on the advancing blade of the Savonius turbine and thus increases its power coefficient near the optimum tip speed ratio.

Sign in / Sign up

Export Citation Format

Share Document