Numerical and Experimental Aerodynamic Investigation of a Low Pressure Steam Turbine Module

2019 ◽  
Author(s):  
Juri Bellucci ◽  
Lorenzo Peruzzi ◽  
Andrea Arnone ◽  
Lorenzo Arcangeli ◽  
Nicola Maceli
Keyword(s):  
Steam Turbine ◽  
Three Dimensional ◽  
Low Pressure ◽  
Operating Conditions ◽  
Performance Estimation ◽  
Experimental Results ◽  
Steam Turbines ◽  
Performance Curves ◽  
Pressure Steam ◽  
Cfd Analyses

Abstract This work aims to deepen the understanding of the aerodynamic behavior and the performance of a low pressure steam turbine module. Numerical and experimental results obtained on a three-stage low pressure steam turbine (LPT) module are presented. The selected geometry is representative of the state-of-the-art of low pressure sections for small steam turbines. The test vehicle was designed and operated in different operating conditions with dry and wet steam. Different types of measurements are performed for the global performance estimation of the whole turbine and for the detailed analysis of the flow field. Steady and unsteady CFD analyses have been performed by means of viscous, three-dimensional simulations adopting a real gas, equilibrium steam model. Measured inlet/outlet boundary conditions are used for the computations. The fidelity of the computational setup is proven by comparing computational and experimental results. Main performance curves and span-wise distributions show a good agreement in terms of both shape of curves/distributions and absolute values. Finally, an attempt is done to point out where losses are generated and the physical mechanisms involved are investigated and discussed in details.

Sequential vs Multidisciplinary Coupled Optimization and Efficient Surrogate Modelling of a Last Stage and the Successive Axial Radial Diffuser in a Low Pressure Steam Turbine

2014 ◽  
Author(s):  
Kevin Cremanns ◽  
Dirk Roos ◽  
Arne Graßmann
Keyword(s):  
Steam Turbine ◽  
Design Process ◽  
Energy Demand ◽  
Three Dimensional ◽  
Flow Simulation ◽  
Low Pressure ◽  
Steam Turbines ◽  
Low Pressure Turbine ◽  
Pressure Steam ◽  
Last Stage

In order to meet the requirements of rising energy demand, one goal in the design process of modern steam turbines is to achieve high efficiencies. A major gain in efficiency is expected from the optimization of the last stage and the subsequent diffuser of a low pressure turbine (LP). The aim of such optimization is to minimize the losses due to separations or inefficient blade or diffuser design. In the usual design process, as is state of the art in the industry, the last stage of the LP and the diffuser is designed and optimized sequentially. The potential physical coupling effects are not considered. Therefore the aim of this paper is to perform both a sequential and coupled optimization of a low pressure steam turbine followed by an axial radial diffuser and subsequently to compare results. In addition to the flow simulation, mechanical and modal analysis is also carried out in order to satisfy the constraints regarding the natural frequencies and stresses. This permits the use of a meta-model, which allows very time efficient three dimensional (3D) calculations to account for all flow field effects.

Detailed Numerical Study of the Main Sources of Loss and Flow Behavior in Low Pressure Steam Turbine Exhaust Hoods

2017 ◽  
Author(s):  
Dickson Munyoki ◽  
Markus Schatz ◽  
Damian M. Vogt
Keyword(s):  
Steam Turbine ◽  
Numerical Study ◽  
Flow Behavior ◽  
Low Pressure ◽  
Operating Conditions ◽  
Pressure Recovery ◽  
Exhaust Hood ◽  
Recovery Coefficient ◽  
Pressure Steam ◽  
Underlying Mechanisms

The performance of the axial-radial diffuser downstream of the last low-pressure steam turbine stages and the losses occurring subsequently within the exhaust hood directly influences the overall efficiency of a steam power plant. It is estimated that an improvement of the pressure recovery in the diffuser and exhaust hood by 10% translates into 1% of last stage efficiency [11]. While the design of axial-radial diffusers has been the object of quite many studies, the flow phenomena occurring within the exhaust hood have not received much attention in recent years. However, major losses occur due to dissipation within vortices and inability of the hood to properly diffuse the flow. Flow turning from radial to downward flow towards the condenser, especially at the upper part of the hood is essentially the main cause for this. This paper presents a detailed analysis of the losses within the exhaust hood flow for two operating conditions based on numerical results. In order to identify the underlying mechanisms and the locations where dissipation mainly occurs, an approach was followed, whereby the diffuser inflow is divided into different sectors and pressure recovery, dissipation and finally residual kinetic energy of the flow originating from these sectors is calculated at different locations within the hood. Based on this method, the flow from the topmost sectors at the diffuser inlet is found to cause the highest dissipation for both investigated cases. Upon hitting the exhaust hood walls, the flow on the upper part of the diffuser is deflected, forming complex vortices which are stretching into the condenser and interacting with flow originating from other sectors, thereby causing further swirling and generating additional losses. The detailed study of the flow behavior in the exhaust hood and the associated dissipation presents an opportunity for future investigations of efficient geometrical features to be introduced within the hood to improve the flow and hence the overall pressure recovery coefficient.

Modeling Partial Admission in Control Stages of Small Steam Turbines With CFD

2018 ◽  
Author(s):  
Juri Bellucci ◽  
Filippo Rubechini ◽  
Andrea Arnone
Keyword(s):  
Steam Turbine ◽  
Three Dimensional ◽  
Admission Rate ◽  
Point Of View ◽  
Test Case ◽  
Steam Turbines ◽  
Turbine Stage ◽  
Performance Curves ◽  
Partial Admission ◽  
The Impact

This work aims at investigating the impact of partial admission on a steam turbine stage, focusing on the aerodynamic performance and the mechanical behavior. The partialized stage of a small steam turbine was chosen as test case. A block of nozzles was glued in a single “thick nozzle” in order to mimic the effect of a partial admission arc. Numerical analyses in full and in partial admission cases were carried out by means of three-dimensional, viscous, unsteady simulations. Several cases were tested by varying the admission rate, that is the length of the partial arc, and the number of active sectors of the wheel. The goal was to study the effect of partial admission conditions on the stage operation, and, in particular on the shape of stage performance curves as well as on the forces acting on bucket row. First of all, a comparison between the flow field of the full and the partial admission case is presented, in order to point out the main aspects related to the presence of a partial arc. Then, from an aerodynamic point of view, a detailed discussion of the modifications of unsteady rows interaction (potential, shock/wake), and how these ones propagate downstream, is provided. The attention is focused on the phenomena experienced in the filling/emptying region, which represent an important source of aerodynamic losses. The results try to deepen the understanding in the loss mechanisms involved in this type of stage. Finally, some mechanical aspects are addressed, and the effects on bucket loading and on aeromechanical forcing are investigated.

Advanced Water Droplet Erosion Protection for Modern Low Pressure Steam Turbine Steel Blades

2015 ◽  
Author(s):  
Joerg Schuerhoff ◽  
Andrei Ghicov ◽  
Karsten Sattler
Keyword(s):  
Steam Turbine ◽  
Water Droplet ◽  
Precipitation Hardening ◽  
Turbine Blades ◽  
Low Pressure ◽  
Steam Turbines ◽  
Treatment Facility ◽  
Material Loss ◽  
Pressure Steam ◽  
Steam Turbine Blades

Blades for low pressure steam turbines operate in flows of saturated steam containing water droplets. The water droplets can impact rotating last stage blades mainly on the leading edge suction sides with relative velocities up to several hundred meters per second. Especially on large blades the high impact energy of the droplets can lead to a material loss particularly at the inlet edges close to the blade tips. This effect is well known as “water droplet erosion”. The steam turbine manufacturer use several techniques, like welding or brazing of inlays made of erosion resistant materials to reduce the material loss. Selective, local hardening of the blade leading edges is the preferred solution for new apparatus Siemens steam turbines. A high protection effect combined with high process stability can be ensured with this Siemens hardening technique. Furthermore the heat input and therewith the geometrical change potential is relatively low. The process is flexible and can be adapted to different blade sizes and the required size of the hardened zones. Siemens collected many years of positive operational experience with this protection measure. State of the art turbine blades often have to be developed with precipitation hardening steels and/or a shroud design to fulfill the high operational requirements. A controlled hardening of the inlet edges of such steam turbine blades is difficult if not impossible with conventional methods like flame hardening. The Siemens steam turbine factory in Muelheim, Germany installed a fully automated laser treatment facility equipped with two co-operating robots and two 6 kW high power diode laser to enable the in-house hardening of such blades. Several blade designs from power generation and industrial turbines were successfully laser treated within the first year in operation. This paper describes generally the setup of the laser treatment facility and the application for low pressure steam turbine blades made of precipitation hardening steels and blades with shroud design, including the post laser heat treatments.

Some Aspects of CFD Modeling in the Analysis of a Low-Pressure Steam Turbine

2007 ◽  
Author(s):  
Filippo Rubechini ◽  
Michele Marconcini ◽  
Andrea Arnone ◽  
Stefano Cecchi ◽  
Federico Dacca`
Keyword(s):  
Steam Turbine ◽  
Computational Cost ◽  
Three Dimensional ◽  
Low Pressure ◽  
Design Tool ◽  
Cfd Modeling ◽  
Navier Stokes ◽  
Sources And Sinks ◽  
Leakage Flows ◽  
Pressure Steam

A three-dimensional, multistage, Navier-Stokes solver is applied to the numerical investigation of a four stage low-pressure steam turbine. The thermodynamic behavior of the wet steam is reproduced by adopting a real-gas model, based on the use of gas property tables. Geometrical features and flow-path details consistent with the actual turbine geometry, such as cavity purge flows, shroud leakage flows and partspan snubbers, are accounted for, and their impact on the turbine performance is discussed. These details are included in the analysis using simple models, which prevent a considerable growth of the computational cost and make the overall procedure attractive as a design tool for industrial purposes. Shroud leakage flows are modeled by means of suitable endwall boundary conditions, based on coupled sources and sinks, while body forces are applied to simulate the presence of the damping wires on the blades. In this work a detailed description of these models is provided, and the results of computations are compared with experimental measurements.

Numerical Investigation of Exhaust Diffuser Performances in Low Pressure Turbine Casings

2011 ◽  
Author(s):  
Tadashi Tanuma ◽  
Yasuhiro Sasao ◽  
Satoru Yamamoto ◽  
Shinji Takada ◽  
Yoshiki Niizeki ◽  
...  
Keyword(s):  
Steam Turbine ◽  
High Performance ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Measurement Data ◽  
Boundary Layer Separation ◽  
Low Pressure ◽  
Tvd Scheme ◽  
Steam Turbines ◽  
Exhaust Hood

Low pressure (LP) exhaust hoods are an important component of steam turbines. The aerodynamic loss of LP exhaust hoods is almost the same as those of the stator and rotor blading in LP steam turbines. Designing high performance LP exhaust hoods should lead further enhancement of steam turbine efficiency. This paper presents the results of exhaust hood computational fluid dynamics (CFD) analyses using last stage exit velocity distributions measured in a full-scale development steam turbine as the inlet boundary condition to improve the accuracy of the CFD analysis. One of the main difficulties in predicting the aerodynamic performance of the exhaust hoods is the unsteady boundary layer separation of exhaust hood diffusers. A highly accurate unsteady numerical analysis is introduced in order to simulate the diffuser flows in LP exhaust hoods. Compressible Navier-Stokes equations and mathematical models for nonequilibrium condensation are solved using the high-order high-resolution finite-difference method based on the fourth-order compact MUSCL TVD scheme, Roe’s approximate Riemann solver, and the LU-SGS scheme. The SST turbulence model is also solved for evaluating the eddy viscosity. The computational results were validated using the measurement data, and the present CFD method was proven to be suitable as a useful tool for determining optimum three-dimensional designs of LP turbine exhaust diffusers.

Computations for Unsteady Compressible Flows in a Multi-Stage Steam Turbine With Steam Properties at Low Load Operations

2010 ◽  
Author(s):  
Shigeki Senoo ◽  
Kiyoshi Segawa ◽  
Hisashi Hamatake ◽  
Takeshi Kudo ◽  
Tateki Nakamura ◽  
...  
Keyword(s):  
Steam Turbine ◽  
Compressible Flows ◽  
Reverse Flow ◽  
Three Dimensional ◽  
Computation Time ◽  
Steam Turbines ◽  
Multi Stage ◽  
Low Load ◽  
Pressure Steam ◽  
Load Conditions

A computational technique for compressive fluid in multistage steam turbines which can allow for thermodynamic properties of steam is presented. The understanding and prediction of flow field not only at design conditions but also at off-design conditions are important for realizing high-performance and high-reliability steam turbines. Computational fluid dynamics is useful for estimations of flows. However, current three-dimensional multi-stage calculations for unsteady flows have two main problems. One is the long computation time and the other is how to include the thermodynamic properties of steam. Properties of the ideal gas, such as equations of state and enthalpy formula, are assumed in most computational techniques for compressible flows. In order to shorten the computation time, a quasi-three-dimensional flow calculation technique is developed. In the analysis, system equations of conservation laws for compressible fluid in axisymmetric cylindrical coordinates are solved by using a finite volume method based on an approximate Riemann solver. Blade forces are calculated from the camber and lean angles of blades using momentum equations. The axisymmetric assumption and the blade force model enable the effective calculation for multi-stage flows, even when the flow is strongly unsteady under off-design conditions. In order to take into account steam properties including effects of the gas-liquid phase change and two-phase flow, a flux-splitting procedure of compressible flow is generalized for real fluid. Density and internal energy per unit volume are selected as independent thermodynamic variables. Pressure and temperature in a superheated region or wetness mass fraction in a wet region are calculated by using a steam table. To improve computational efficiency, a discretized steam table matrix is made in which the density and specific internal energy are independent variables. For accuracy and continuity of steam properties, the second order Taylor expansion and linear interpolation are introduced. The computed results of last four-stage low-pressure steam turbine at low load conditions show that there is a reverse flow near the hub region of the last (fourth stage bucket and the flow concentrates in the tip region due to the centrifugal force. At a very low load condition, the reverse flow region extends to the former (i.e. the first to third) stages and the unsteadiness of flow gets larger due to many vortices. Four-stage low pressure steam turbine tests are also carried out at low load or even zero load. The radial distributions of flow direction downstream from each stage are measured by traversing pneumatic probes. Additionally pressure transducers are installed in the side wall to measure the unsteady pressure. The regions of reverse flow are compared between computations and experiments at different load conditions, and their agreement is good. Further, the computation can follow the trends of standard deviation of unsteady pressure on the wall to volumetric flow rate of experiments. The validity of the analysis method is verified.

A Methodology for a Detailed Loss Prediction in Low Pressure Steam Turbines

2017 ◽  
Author(s):  
Marius Grübel ◽  
Robin M. Dovik ◽  
Markus Schatz ◽  
Damian M. Vogt
Keyword(s):  
Boundary Layer ◽  
Evaluation Method ◽  
Three Dimensional ◽  
Low Pressure ◽  
Steam Turbines ◽  
Cfd Simulations ◽  
Depth Analysis ◽  
Pressure Steam ◽  
The Impact ◽  
Loss Mechanisms

An evaluation method for CFD simulations is presented, which allows an in-depth analysis of different loss mechanisms applying the approach of entropy creation proposed by Denton. The entropy creation within each single mesh element is determined based on the entropy flux through the cell faces and therefore the locations, where losses occur, can be identified clearly. By using unique features of the different loss mechanisms present in low pressure steam turbines, the losses are categorized into boundary layer, wake mixing and shock losses as well as thermodynamic wetness losses. The suitability of the evaluation method is demonstrated by means of steady state CFD simulations of the flow through a generic last stage of a low pressure steam turbine. The simulations have been performed on streamtubes extracted from three-dimensional simulations representing the flow at 10 % span. The impact of non-equilibrium steam effects on the overall loss composition of the stator passage is investigated by comparing the results to an equilibrium steam simulation. It is shown, that the boundary layer losses for the investigated case are of similar magnitude, but the shock and wake losses exhibit significant differences.

Experimental and Numerical Investigation of the Flow in a Low-Pressure Industrial Steam Turbine With Part-Span Connectors

2016 ◽  
Vol 138 (7) ◽  
Author(s):  
Markus Häfele ◽  
Christoph Traxinger ◽  
Marius Grübel ◽  
Markus Schatz ◽  
Damian M. Vogt ◽  
...  
Keyword(s):  
Flow Field ◽  
Steam Turbine ◽  
Numerical Study ◽  
Three Dimensional ◽  
Low Pressure ◽  
Operating Conditions ◽  
Engineering Practice ◽  
Cfd Model ◽  
Wide Range ◽  
The Impact

An experimental and numerical study on the flow in a three-stage low-pressure (LP) industrial steam turbine is presented and analyzed. The investigated LP section features conical friction bolts in the last and a lacing wire in the penultimate rotor blade row. These part-span connectors (PSC) allow safe turbine operation over an extremely wide range and even in blade resonance condition. However, additional losses are generated which affect the performance of the turbine. In order to capture the impact of PSCs on the flow field, extensive measurements with pneumatic multihole probes in an industrial steam turbine test rig have been carried out. State-of-the-art three-dimensional computational fluid dynamics (CFD) applying a nonequilibrium steam (NES) model is used to examine the aerothermodynamic effects of PSCs on the wet steam flow. The vortex system in coupled LP steam turbine rotor blading is discussed in this paper. In order to validate the CFD model, a detailed comparison between measurement data and steady-state CFD results is performed for several operating conditions. The investigation shows that the applied one-passage CFD model is able to capture the three-dimensional flow field in LP steam turbine blading with PSC and the total pressure reduction due to the PSC with a generally good agreement to measured values and is therefore sufficient for engineering practice.

A generic low-pressure steam turbine test case for aeromechanics and condensation

2019 ◽  
Vol 233 (7) ◽  
pp. 953-958
Author(s):  
Christopher Fuhrer ◽  
Marius Grübel ◽  
Damian M Vogt
Keyword(s):  
Steam Turbine ◽  
Numerical Test ◽  
Low Pressure ◽  
Test Case ◽  
Test Cases ◽  
Steam Turbines ◽  
Aerodynamic Damping ◽  
Spontaneous Condensation ◽  
Pressure Steam ◽  
Turbine Design

At the Institute of Thermal Turbomachinery and Machniery Laboratory (ITSM) a generic test case was designed to investigate aeromechanical phenomena and condensation in low-pressure steam turbines. This test case, referred to as Steam turbine Test case for Aeromechanics and Condensation (STAC) consists of the two last stages of a low-pressure steam turbine and is representative for a modern steam turbine design. STAC is intended to serve as a numerical test case to allow studying the fields of aerodynamic damping and spontaneous condensation in low-pressure steam turbine last stages. The geometry of the turbine is made available online at www.itsm.uni-stuttgart.de/research/test-cases/ .

Sign in / Sign up

Export Citation Format

Share Document