Effects of Port Fuel and Direct Injection Strategies and Intake Conditions on Gasoline Compression Ignition Operation

2018 ◽  
Author(s):  
Buyu Wang ◽  
Michael Pamminger ◽  
Thomas Wallner
Keyword(s):  
Heat Transfer ◽  
High Temperature ◽  
Thermal Efficiency ◽  
Direct Injection ◽  
Pressure Rise ◽  
Low Temperature Combustion ◽  
Compression Ignition ◽  
Rise Rate ◽  
Temperature Combustion ◽  
Injection Strategies

Gasoline compression ignition (GCI) using a single gasoline-type fuel for port fuel and direct injection has been shown as a method to achieve low-temperature combustion with low engine-out NOx and soot emissions and high indicated thermal efficiency. However, key technical barriers to achieving low temperature combustion on multi-cylinder engines include the air handling system (limited amount of exhaust gas recirculation (EGR)) as well as mechanical engine limitations (e.g. peak pressure rise rate). In light of these limitations, high temperature combustion with reduced amounts of EGR appears more practical. Furthermore, for high temperature GCI, an effective aftertreatment system allows high thermal efficiency with low tailpipe-out emissions. In this work, experimental testing was conducted on a 12.4 L multi-cylinder heavy-duty diesel engine operating with high temperature GCI combustion using EEE gasoline. Engine testing was conducted at an engine speed of 1038 rpm and brake mean effective pressure (BMEP) of 14 bar. Port fuel and direct injection strategies were utilized to increase the premixed combustion fraction. The impact on engine performance and emissions with respect to varying the injection and intake operating parameters was quantified within this study. A combined effect of reducing heat transfer and increasing exhaust loss resulted in a flat trend of brake thermal efficiency (BTE) when retarding direct injection timing, while increased port fuel mass improved BTE due to advanced combustion phasing and reduced heat transfer loss. Overall, varying intake valve close timing, EGR, intake pressure and temperature with the current pressure rise rate and soot emissions constraint was not effective in improving BTE, as the benefit of low heat transfer loss was always offset by increased exhaust loss.

scholarly journals Impact of injection strategies on combustion characteristics, efficiency and emissions of gasoline compression ignition operation in a heavy-duty multi-cylinder engine

2018 ◽  
Vol 21 (8) ◽  
pp. 1426-1440 ◽  
Author(s):  
Buyu Wang ◽  
Michael Pamminger ◽  
Ryan Vojtech ◽  
Thomas Wallner
Keyword(s):  
High Temperature ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Pressure Rise ◽  
Pilot Injection ◽  
Low Temperature Combustion ◽  
Compression Ignition ◽  
Temperature Combustion ◽  
Gas Recirculation ◽  
Direct Fuel Injection

Gasoline compression ignition using a single gasoline-type fuel for direct/port injection has been shown as a method to achieve low-temperature combustion with low engine-out NOx and soot emissions and high indicated thermal efficiency. However, key technical barriers to achieving low-temperature combustion on multi-cylinder engines include the air handling system (limited amount of exhaust gas recirculation) as well as mechanical engine limitations (e.g. peak pressure rise rate). In light of these limitations, high-temperature combustion with reduced amounts of exhaust gas recirculation appears more practical. Furthermore, for high-temperature gasoline compression ignition, an effective aftertreatment system allows high thermal efficiency with low tailpipe-out emissions. In this work, experimental testing was conducted on a 12.4 L multi-cylinder heavy-duty diesel engine operating with high-temperature gasoline compression ignition combustion with port and direct injection. Engine testing was conducted at an engine speed of 1038 r/min and brake mean effective pressure of 1.4 MPa for three injection strategies, late pilot injection, early pilot injection, and port/direct fuel injection. The impact on engine performance and emissions with respect to varying the combustion phasing were quantified within this study. At the same combustion phasing, early pilot injection and port/direct fuel injection had an earlier start of combustion and higher maximum pressure rise rates than late pilot injection attributable to more premixed fuel from pilot or port injection; however, brake thermal efficiencies were higher with late pilot injection due to reduced heat transfer. Early pilot injection also exhibited the highest cylinder-to-cylinder variations due to differences in injector behavior as well as the spray/wall interactions affecting mixing and evaporation process. Overall, peak brake thermal efficiency of 46.1% and 46% for late pilot injection and port/direct fuel injection was achieved comparable to diesel baseline (45.9%), while early pilot injection showed the lowest brake thermal efficiency (45.3%).

scholarly journals Combustion and Emissions of Gasoline Compression Ignition Engine Fuelled with Gasoline-Biodiesel Blends

2021 ◽  
Author(s):  
Yanuandri Putrasari ◽  
Ocktaeck Lim
Keyword(s):  
Combustion Engine ◽  
Direct Injection ◽  
Pressure Rise ◽  
Maximum Pressure ◽  
Compression Ignition ◽  
Biodiesel Blends ◽  
Fuel Blends ◽  
Rise Rate ◽  
Gas Recirculation ◽  
Injection Strategies

A gasoline compression ignition (GCI) engine was proposed to be the next generation internal combustion engine for gasoline. The effect of exhaust gas recirculation (EGR) and intake boosting on combustion and emissions of GCI engine fueled with gasoline-biodiesel blends by partially premixed compression ignition (PPCI) combustions are investigated in this study. Tests were conducted on a single-cylinder direct-injection CI engine, with 5% by volume proportion of biodiesel in gasoline fuel blends. Engine control parameters (EGR rate, intake boosting rate, and various injection strategies) were adjusted to investigate their influences on combustion and emissions of this GCI engine. It is found that changes in EGR rate, intake boosting pressure and injection strategies affect on ignition delay, maximum pressure rise rate and thermal efficiency which is closely tied to HC, CO, NOx and smoke emissions, respectively.

Operating Limits of Spark-Assisted Compression Ignition Combustion Under Boosted Ultra-EGR Dilute Conditions in a Negative Valve Overlap Engine

2019 ◽  
Author(s):  
Vassilis Triantopoulos ◽  
Jason B. Martz ◽  
Jeff Sterniak ◽  
George Lavoie ◽  
Dennis N. Assanis ◽  
...  
Keyword(s):  
Low Temperature ◽  
Heat Release ◽  
Engine Speed ◽  
Pressure Rise ◽  
Stability Limit ◽  
Maximum Pressure ◽  
Low Temperature Combustion ◽  
Compression Ignition ◽  
Temperature Combustion ◽  
Operating Limits

Abstract Spark-assisted compression ignition (SACI) is a low temperature combustion mode that can offer thermal efficiency improvements and lower nitrogen oxide emissions compared to conventional spark-ignited combustion. However, the SACI operating range is often limited due to excessive pressure rise rates driven by rapid heat release rates. Well-controlled experiments were performed to investigate the SACI operating limits under previously unexplored boosted, stoichiometric, EGR dilute conditions, where low temperature combustion engines promise high thermodynamic efficiencies. At higher intake boost, the SACI high load limit shifted towards lower fuel-to-charge equivalence ratio mixtures, creating a larger gap between the conventional spark-ignition EGR dilution limit and the boosted SACI operating limits. Combustion phasing retard was very effective at reducing maximum pressure rise rate levels until the stability limit, primarily due to slower end-gas burn rates. Gross fuel conversion efficiency improvements up to 10% were observed by using intake boost for either load expansion or dilution extension. Changes in engine speed necessitated changes in unburned gas temperature to match autoignition timing, but were shown to have negligible impact on the heat release profile on a crank angle basis. Lower engine speeds were favorable for load expansion, as time-based peak pressure rise rates scaled with engine speed.

scholarly journals Use of Adaptive Injection Strategies to Increase the Full Load Limit of RCCI Operation

2015 ◽  
Author(s):  
Reed Hanson ◽  
Andrew Ickes ◽  
Thomas Wallner
Keyword(s):  
Natural Gas ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Peak Load ◽  
Combustion Process ◽  
Pressure Rise ◽  
Dual Fuel ◽  
The Impact ◽  
Injection Strategies

Dual-fuel combustion using port-injection of low reactivity fuel combined with direct injection of a higher reactivity fuel, otherwise known as Reactivity Controlled Compression Ignition (RCCI), has been shown as a method to achieve low-temperature combustion with moderate peak pressure rise rates, low engine-out soot and NOx emissions, and high indicated thermal efficiency. A key requirement for extending to high-load operation is moderating the reactivity of the premixed charge prior to the diesel injection. One way to accomplish this is to use a very low reactivity fuel such as natural gas. In this work, experimental testing was conducted on a 13L multi-cylinder heavy-duty diesel engine modified to operate using RCCI combustion with port injection of natural gas and direct injection of diesel fuel. Engine testing was conducted at an engine speed of 1200 RPM over a wide variety of loads and injection conditions. The impact on dual-fuel engine performance and emissions with respect to varying the fuel injection parameters is quantified within this study. The injection strategies used in the work were found to affect the combustion process in similar ways to both conventional diesel combustion and RCCI combustion for phasing control and emissions performance. As the load is increased, the port fuel injection quantity was reduced to keep peak cylinder pressure and maximum pressure rise rate under the imposed limits. Overall, the peak load using the new injection strategy was shown to reach 22 bar BMEP with a peak brake thermal efficiency of 47.6%.

scholarly journals Optimization of gasoline compression ignition combustion with ozone addition and two-stage direct-injection at middle loads

2021 ◽  
pp. 146808742098457
Author(s):  
Yoshimitsu Kobashi ◽  
Tu Dan Dan Da ◽  
Ryuya Inagaki ◽  
Gen Shibata ◽  
Hideyuki Ogawa
Keyword(s):  
Ozone Concentration ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Pressure Rise ◽  
Maximum Pressure ◽  
Injection Timing ◽  
Compression Ignition ◽  
Ozone Addition ◽  
Primary Reference

Ozone (O3) was introduced into the intake air to control the ignition in a gasoline compression ignition (GCI) engine. An early fuel injection at −68 °CA ATDC was adopted to mix the fuel with the reactive O-radicals decomposed from the O3, before the reduction of the O-radicals due to their recombination would take place. The second injection was implemented near top dead center to optimize the profile of the heat release rate. The engine experiments were performed around the indicated mean effective pressure (IMEP) of 0.67 MPa with a primary reference fuel, octane number 90 (PRF90), maintaining the 15% intake oxygen concentration with the EGR. The quantity of the first injection, the second injection timing as well as the ozone concentration were changed as experimental parameters. The results showed that the GCI operation with the ozone addition makes it possible to reduce the maximum pressure rise rate while attaining high thermal efficiency, compared to that without the ozone. Appropriate combinations of the ozone concentration and the first injection quantity achieve low smoke and NOx emissions. Further, the ozone-assisted GCI operation was compared with conventional diesel operation. The results showed that the indicated thermal efficiency of the ozone-assisted GCI combustion is slightly lower than that of the conventional diesel combustion, but that GCI assisted with ozone is highly advantageous to the smoke and NOx emissions.

Fuel Stratification and Partially Premixed Combustion With Neat N-Butanol in a Compression Ignition Engine

2017 ◽  
Author(s):  
Shouvik Dev ◽  
Tongyang Gao ◽  
Xiao Yu ◽  
Mark Ives ◽  
Ming Zheng
Keyword(s):  
Direct Injection ◽  
Pressure Rise ◽  
Premixed Combustion ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Engine Load ◽  
Fuel Stratification ◽  
Partially Premixed Combustion ◽  
Rise Rate ◽  
Partially Premixed

Homogeneous Charge Compression Ignition (HCCI) has been considered as an ideal combustion mode for compression ignition engines due to its superb thermal efficiency and low emissions of nitrogen oxides (NOx) and particulate matter (PM). However, a challenge that limits practical applications of HCCI is the lack of control over the combustion rate, which either deteriorates thermal efficiency at low engine load, or produces excessive pressure rise rate and combustion noise at high engine load. Fuel stratification and partially premixed combustion (PPC) have considerably improved the control over the heat release profile with modulations of the ratio between premixed fuel and directly injected fuel, as well as injection timing for ignition initiation. It leverages the advantages of both conventional direct injection compression ignition and HCCI. Compared with those of HCCI, the ignition ability and combustion efficiency of PPC are significantly enhanced at low engine load, and the low emissions of NOx and PM are maintained with lower pressure rise rate. In this study, neat n-butanol is employed to generate the fuel stratification and partially premixed combustion in a single cylinder compression ignition engine. A fuel such as n-butanol can provide additional benefits of even lower emissions, and can potentially lead to a reduced carbon footprint and improved energy security if produced appropriately from biomass sources. Intake port fuel injection (PFI) of neat n-butanol is used for the delivery of the premixed fuel, while the direct injection (DI) of neat n-butanol is applied to generate the fuel stratification. Effects of PFI-DI fuel ratio, DI timing, and intake pressure, on the combustion, are studied in detail. Different conditions are identified at which clean and efficient combustion can be achieved at a baseline load of 6 bar IMEP. An extended load of 14 bar IMEP is demonstrated using stratified combustion with combustion phasing control.

An experimental study of the injection strategies on engine performance of the butanol/biodiesel dual-fuel Intelligent Charge Compression Ignition mode

2020 ◽  
pp. 146808742096399
Author(s):  
Wenbin Zhao ◽  
Yaoyuan Zhang ◽  
Guan Huang ◽  
Zilong Li ◽  
Yong Qian ◽  
...  
Keyword(s):  
Heat Release ◽  
Thermal Efficiency ◽  
Direct Injection ◽  
Dual Fuel ◽  
Injection Timing ◽  
Nox Emissions ◽  
Compression Ignition ◽  
Combustion Mode ◽  
Low Levels ◽  
Injection Strategies

Intelligent Charge Compression Ignition (ICCI) combustion mode is a novel dual-fuel combustion strategy that has been proposed recently. In ICCI combustion mode, two fuels with different reactivity are directly injected during the intake stroke and compression stroke, respectively, to achieve flexible reactivity gradient and equivalence ratio stratification. In this study, experiments were conducted on a single-cylinder diesel engine to investigate the effects of butanol direct injection strategies on the engine running with ICCI combustion mode at a constant speed of 1500 r/min and medium load. Results showed that ICCI combustion mode was composed of premixed heat release and diffusion heat release. In compare, the percentage of premixed heat release was higher than the diffusion heat release. With fixed biodiesel direct injection timing (SOI2), retarding butanol single injection timing (SOI1) would delay combustion phasing while not distinctively affect ignition timing. SOI1 showed significant effect on the thermal efficiency and engine emissions. Indicated thermal efficiency (ITE) decreased at first and then slightly increased with retarding of SOI1, while the nitrogen oxides (NOx) emissions were always at low levels. As the butanol second direct injection timing (SOI1-2) retard and the corresponding energy ratio increase, more butanol entered into the crevice/squish regions, leading to the increase of unburned hydrocarbon (HC) and carbon monoxide (CO) emissions. EGR strategy helps to significantly reduce NOx emissions without affecting ITE although penalized HC and CO emissions are resulted in. The optimum butanol direct injection strategies were butanol single direct injection, especially in the early SOI1, in which the thermal efficiency was higher and emissions were at very low levels (NOx  < 0.4 g/kW h).

Postinjection Strategy for the Reduction of the Peak Pressure Rise Rate of Neat n-Butanol Combustion

2016 ◽  
Vol 138 (9) ◽  
Author(s):  
Marko Jeftić ◽  
Ming Zheng
Keyword(s):  
Nitrogen Oxide ◽  
Thermal Efficiency ◽  
Peak Pressure ◽  
Pressure Rise ◽  
Compression Ignition ◽  
Cylinder Pressure ◽  
Compression Ignition Engine ◽  
Pressure Rise Rate ◽  
Rise Rate ◽  
Load Conditions

Enhanced premixed combustion of neat butanol in a compression ignition engine can have challenges with regards to the peak pressure rise rate (PRR) and the peak in-cylinder pressure. It was proposed to utilize a butanol postinjection to reduce the peak PRR and the peak in-cylinder pressure while maintaining a constant engine load. Postinjection timing and duration sweeps were carried out with neat n-butanol in a compression ignition engine. The postinjection timing sweep results indicated that the use of an early butanol postinjection reduced the peak PRR and the peak in-cylinder pressure and it was observed that there was an optimal postinjection timing range for the maximum reduction of these parameters. The results also showed that an early postinjection of butanol increased the nitrogen oxide emissions, and a Fourier transform infrared spectroscopy (FTIR) analysis revealed that late postinjections increased the emissions of unburned butanol. The postinjection duration sweep indicated that the peak PRR was significantly reduced by increasing the postinjection duration at constant load conditions. There was also a reduction in the peak in-cylinder pressure. Measurements with a hydrogen mass spectrometer showed that there was an increased presence of hydrogen in the exhaust gas when the postinjection duration was increased but the total yield of hydrogen was relatively low. It was observed that the coefficient of variation for the indicated mean effective pressure was significantly increased and that the indicated thermal efficiency was reduced when the postinjection duration was increased. The results also showed that there were increased nitrogen oxide, carbon monoxide, and total hydrocarbon (THC) emissions for larger postinjections. Although the use of a postinjection resulted in emission and thermal efficiency penalties at medium load conditions, the results demonstrated that the postinjection strategy successfully reduced the peak PRR, and this characteristic can be potentially useful for higher load applications where the peak PRR is of greater concern.

Sign in / Sign up

Export Citation Format

Share Document