Friction and Wear Behavior of Polyetherimide(PEI) Filled With Polytetrafluoroethylene(PTFE)

2010 ◽  
Author(s):  
LiQin Wang ◽  
JianWei Sun ◽  
Le Gu
Keyword(s):  
Friction Coefficient ◽  
Dry Friction ◽  
Friction And Wear ◽  
Wear Behavior ◽  
Surface Hardness ◽  
Tribological Performance ◽  
Friction Condition ◽  
Test Rig ◽  
Friction And Wear Behavior ◽  
Ring Configuration

The tribological performance of Polyetherimide (PEI) composites filled with different Polytetrafluoroethylene (PTFE) content was comparatively evaluated on MM-200 test rig in block-on-ring configuration under dry friction condition. The microstructures of worn surfaces, fractured surfaces and wear mechanisms of the PEI composite were examined under scanning electron microscope (SEM). The variations of elastic modulus and surface hardness with variation in composition were also investigated. The results showed that under conditions of dry friction the PTFE can lower the friction coefficient and reduce wear of the PEI composites. When filled with 10 wt. % PTFE, the composite had the lowest wear rate. For PEI filled with 5wt. % PTFE the friction coefficient was about 0.3 and remained comparatively stable with increase of the PTFE content.

Study on Tribology Performance and Wear Controlling of 9Cr2Mo Steel

2010 ◽  
Vol 139-141 ◽  
pp. 414-417 ◽  
Author(s):  
Xiao Ming Jia ◽  
Jin Rong Chai
Keyword(s):  
Friction Coefficient ◽  
Tool Steel ◽  
Dry Friction ◽  
Friction And Wear ◽  
Solid Lubricant ◽  
Cutting Tool ◽  
Wear Behavior ◽  
Friction Process ◽  
Friction And Wear Behavior ◽  
Tribology Performance

9Cr2Mo steel is widely used as measuring and cutting tool steel. The friction and wear behavior of 9Cr2Mo steel was investigated under dry friction and solid lubricant by wear tester. The experiment results show that the friction coefficient of 9Cr2Mo steel is 0.34~0.58 under dry friction and 0.035~0.06 under solid lubricant. With the increase of load , the friction coefficient decreases and the wearing capacity increases under two kinds of conditions. The wearing capacity of 9Cr2Mo steel under solid lubricant is great lower than it under dry friction. The friction process is smooth under solid lubricant. It indicated that the solid lubricant took effect in antifriction and antiwear of 9Cr2Mo steel.

The Friction and Wear of Thin, Sintered, Fluoride Films

1972 ◽  
Vol 94 (1) ◽  
pp. 12-18 ◽  
Author(s):  
M. T. Lavik ◽  
B. D. McConnell ◽  
G. David Moore
Keyword(s):  
Friction Coefficient ◽  
Friction And Wear ◽  
Room Temperature ◽  
Wear Behavior ◽  
Strong Dependence ◽  
Aluminum Phosphate ◽  
Friction And Wear Behavior ◽  
Wear Life ◽  
Compositional Changes ◽  
Cure Temperature

Results are presented for the bonding of thin, sintered, fluoride films of BaF2 and CaF2 with mono-aluminum phosphate. Friction and wear behavior of these films has been defined in terms of film compositional changes, film curing procedures, and substrate variations when subjected to varying levels of temperature and load. Mono-aluminum phosphate was found to greatly enhance the adhesion of the sintered fluoride film. There was a strong dependence of wear life at 1000 deg F on the mono-aluminum phosphate content of the film. Films containing 6 vol. percent phosphate appear to be near optimum and exhibited wear lives of 1,000,000 load cycles under sliding conditions in a dual rub-shoe device with friction coefficient levels in the order of 0.10 to 0.20. Near-optimum values were determined for cure temperature (950 deg C), and surface finish (23 μ in. rms) on rhodium-plated substrates. Graphite and gold were added to the aluminum phosphate bonded BaF2: CaF2 films. Both additives were found to lower the friction coefficient at room temperature.

Dry friction and wear behavior of in-situ Al/Al3Ti composite

2013 ◽  
Vol 48 (9) ◽  
pp. 1049-1059 ◽  
Author(s):  
A Habibolahzadeh ◽  
A Hassani ◽  
E Bagherpour ◽  
M Taheri
Keyword(s):  
Dry Friction ◽  
Friction And Wear ◽  
Wear Behavior ◽  
Friction And Wear Behavior

Friction and Wear Behavior of Polypropylene/Montmorillonite Intercalated Nanocomposites

2011 ◽  
Vol 311-313 ◽  
pp. 92-95 ◽  
Author(s):  
Kui Chen ◽  
Tian Yun Zhang ◽  
Wei Wei
Keyword(s):  
Stainless Steel ◽  
Friction Coefficient ◽  
Wear Rate ◽  
Abrasive Wear ◽  
Wear Mechanisms ◽  
Mass Fraction ◽  
Friction And Wear ◽  
Adhesive Wear ◽  
Wear Behavior ◽  
Friction And Wear Behavior

Polypropylene/organo-montmorillonite (PP/OMMT) composites were investigated by XRD. Friction and wear behaviors of this composites sliding against GCr15 stainless steel were examined on M-2000 text rig in a ring-on-block configuration. Worn surfaces of PP and its composites were analyzed by SEM. The result shows that PP macromolecule chains have intercalated into OMMT layers and form intercalated nanocomposites. With the increase of mass fraction of OMMT, both wear rate and friction coefficient of composites first decrease then rise. With the increase of load, from 150 N, 200 N to 250 N, wear rate of composites increases, while friction coefficient reduces. The wear mechanisms of composites are connected with the content of OMMT. Composites were dominated by adhesive wear, abrasive wear and adhesive wear accompanied by abrasive wear respectively with the increase of OMMT content.

scholarly journals Dry Friction and Wear Behavior of Forged Co–29Cr–6Mo Alloy without Ni and C Additions for Implant Applications

2005 ◽  
Vol 46 (7) ◽  
pp. 1578-1587 ◽  
Author(s):  
Kazushige Kumagai ◽  
Naoyuki Nomura ◽  
Tsukasa Ono ◽  
Masahiro Hotta ◽  
Akihiko Chiba
Keyword(s):  
Dry Friction ◽  
Friction And Wear ◽  
Wear Behavior ◽  
Friction And Wear Behavior

Tribological Performance of PTFE Composites Filled with Spherical-Graphite

2011 ◽  
Vol 197-198 ◽  
pp. 1184-1187
Author(s):  
Jian Wei Sun ◽  
Li Qin Wang ◽  
Le Gu
Keyword(s):  
Friction Coefficient ◽  
Impact Strength ◽  
Wear Rate ◽  
Tribological Performance ◽  
Flake Graphite ◽  
Test Rig ◽  
Ring Configuration ◽  
Spherical Graphite ◽  
Ptfe Composites ◽  
Better Than

The tribologcial performance of PTFE composites filled with different contents of spherical-graphite and Flake-graphite were comparatively evaluated on MM-200 test rig in block-on-ring configuration under dry condition. The microstructures of worn surfaces of PTFE composites were examined with SEM, and wear mechanisms was also analyzed. The changes of notched impact strength with the content changed were also considered. The results show that the tribological performance of spherical-graphite was better than flake-graphite with same weight filled: The friction coefficient of spherical-graphite, about 0.10~0.15, was under flake-graphite, about 0.12~0.18; the wear rate of spherical-graphite was lower than flake-graphite at each content. Notched impact strength of spherical-graphite was from 7.0kJ/m2 to 8.7 kJ/m2 with the content increased, while flake-graphite was fall rapidly from 8.5kJ/m2 to 3.0kJ/m2 with the content added more than 5wt. %.

Study on the Friction and Wear Behavior of Grind-Hardened Layer

2010 ◽  
Vol 431-432 ◽  
pp. 385-388 ◽  
Author(s):  
Jian Hua Zhang ◽  
Pei Qi Ge ◽  
Lei Zhang ◽  
Yang Yu ◽  
Hui Li
Keyword(s):  
Friction Coefficient ◽  
Wear Rate ◽  
Wear Debris ◽  
Friction And Wear ◽  
Wear Behavior ◽  
Hardened Layer ◽  
Hardened Steel ◽  
Wear Performance ◽  
Friction And Wear Behavior ◽  
Grind Hardening

The grind-hardening technology utilizes the grinding heat to harden the surface of the workpiece. The friction and wear performance of the grind-hardened layer is one of the important parameters. In this paper, the friction and wear performance of the grind-hardened layer was studied by the friction and wear experiment. The wear rate and the friction coefficient of the grind-hardened steel were studied by comparing with conventional hardened steel and non-hardened steel. The surface worn morphology and the collected wear debris of the grind-hardened steel were observed during the experiment. The wear mechanism of the grind-hardened steel was analyzed under different friction conditions.

A Comparative Study on the Friction and Wear Properties of Three Different Copper Alloys

2018 ◽  
Vol 913 ◽  
pp. 205-211
Author(s):  
Dong Mei Liu ◽  
Qiang Song Wang ◽  
Wei Yuan ◽  
Xu Jun Mi
Keyword(s):  
Friction Coefficient ◽  
Comparative Study ◽  
Dry Friction ◽  
Friction And Wear ◽  
Copper Alloys ◽  
Friction Condition ◽  
Al Alloy ◽  
Wear Properties ◽  
Friction Coefficients ◽  
Friction And Wear Properties

A comparative study on the friction and wear properties of three kinds of copper alloys, including Cu-Ni based, Cu-Al and Cu-Be alloys was carried out in this study. The friction pair was stainless steel, and both dry and MoS2 lubrication friction experiments were investigated. During the experiments, different loads were chosen for different alloys. It was found that under dry friction condition, the friction coefficients of both Cu-Ni based and Cu-Al alloys did not change as the loads changes, whereas the friction coefficient of Cu-Be alloy increased as the loads increases. Under lubrication friction condition, the friction coefficients of all three alloys did not change as the load changes. The results show that the dry friction coefficient of Cu-Ni based alloy was the largest (0.74), the Cu-Al alloy next (0.60), and the Cu-Be alloy had the smallest dry friction coefficient (0.54). The lubrication friction coefficient of Cu-Ni based and Cu-Be was equal and relatively smaller (0.12), whereas the Cu-Al alloy had a relative larger lubrication friction coefficient (0.27). The microstructure observations were consistent with the friction and wear performance, and the SEM results show that different wear mechanisms were dominated for different alloys.

scholarly journals Friction and Wear Behavior of Polyimide Composites Reinforced by Surface-Modified Poly-p-Phenylenebenzobisoxazole (PBO) Fibers in High Ambient Temperatures

Polymers ◽  
2019 ◽  
Vol 11 (11) ◽  
pp. 1805
Author(s):  
Yu ◽  
Zhang ◽  
Tang ◽  
Gao
Keyword(s):  
Wear Resistance ◽  
Friction Coefficient ◽  
Wear Rate ◽  
Friction And Wear ◽  
Wear Behavior ◽  
Specific Wear Rate ◽  
Interface Properties ◽  
Sliding Velocity ◽  
Friction And Wear Behavior ◽  
Ambient Temperatures

(1) In order to improve the properties of antifriction and wear resistance of polyimide (PI) composite under high temperature conditions, (2) 3-Aminopropyltriethoxysilane (APTES) and Lanthanum (La) salt modifications were employed to manufacture poly-p-phenylenebenzobisoxazole (PBO)/PI composites with different interface properties. The representative ambient temperatures of 130 and 260 °C were chosen to study the friction and wear behavior of composites with different interface properties. (3) Results revealed that while both modification methods can improve the chemical activity of the surface of PBO fibers, the La salt modification is more effective. The friction coefficient of all composites decreases with the increase of sliding velocity and load at two temperatures, and the specific wear rate is increases. Contrary to the situation in the 130 °C environment, the wear resistance of the unmodified composite in the 260 °C environment is greatly affected by the sliding velocity and load, while the modified composites are less affected. Under the same test parameters, the PBO–La/PI composite has the lowest specific wear rate and friction coefficient, and (4) La salt modification is a more effective approach to improve the properties of antifriction and wear resistance of PI composite than APTES modification in high ambient temperatures.

Effect of Nano Sodium Titanate Whisker and Aramid Pulp on the Friction and Wear Behavior of Resin-Based Brake Material

2021 ◽  
Vol 1016 ◽  
pp. 1121-1126
Author(s):  
Zhong Zheng Pei ◽  
Ren Bo Song ◽  
Jie Xu ◽  
Yi Fan Feng ◽  
Ke Guo
Keyword(s):  
Friction Coefficient ◽  
Wear Rate ◽  
Impact Energy ◽  
Friction And Wear ◽  
Wear Behavior ◽  
Sodium Titanate ◽  
Friction And Wear Behavior

The dependence of friction and wear behavior on nanosodium titanate whisker and aramid pulp in a designed resin-based brake material was systematically analyzed. Higher contents of aramid pulp enhanced the hardness of the brake materials. In addition, the maximum impact energy of the material reached 0.392 J/cm2 where the ratio of aramid pulp to sodium titanate whisker is 0.75. At same time, the friction coefficient was stable between 0.38 and 0.45, and the wear rate was 5%. The samples with higher contents of nanosodium titanate whiskers and aramid pulp showed more uniform furrows, fewer delaminated craters, more moderate layers transfer and more stable contact plateaus.

Sign in / Sign up

Export Citation Format

Share Document