Performance Investigation of a Four Stroke Diesel Engine, Using Water-Based Ferrofluid as an Additive

2011 ◽  
Author(s):  
F. Daneshvar ◽  
N. Jahani ◽  
M. B. Shafii
Keyword(s):  
Experimental Study ◽  
Magnetic Nanoparticles ◽  
Diesel Engine ◽  
Diesel Fuel ◽  
Engine Performance ◽  
Brake Specific Fuel Consumption ◽  
Engine Exhaust ◽  
Brake Thermal Efficiency ◽  
Diesel Fuels ◽  
Water Based

In this experimental study, a four stroke diesel engine was conducted to investigate the effect of adding water-based ferrofluid to diesel fuel on engine performance. To our knowledge, Magnetic nanoparticles had not been used before. To this end, emulsified diesel fuels of 0, 0.4, and 0.8 water-based ferrofluid/Diesel ratios by volume were used as fuel. The ferrofluid used in this study was a handmade water-based ferrofluid prepared by the authors. The results show that adding water-based ferrofluid to diesel fuel has a perceptible effect on engine performance, increasing the brake thermal efficiency relatively up to 12%, and decreasing the brake specific fuel consumption relatively up to 11% as compared to diesel fuel. In addition, the results indicate that increasing ferrofluid concentration will magnify the results. Furthermore, it was found that magnetic nanoparticles can be collected at the engine exhaust using magnetic bar.

scholarly journals Comparison between PEE10 and PEE10-Bioethanol Blends on Performance and Emission Characteristics of a HSDI Diesel Engine

2021 ◽  
Vol 18 (22) ◽  
pp. 451
Author(s):  
Ekkachai Sutheerasak ◽  
Charoen Chinwanitcharoen ◽  
Sathaporn Chuepeng
Keyword(s):  
Nitric Oxide ◽  
Carbon Dioxide ◽  
Diesel Engine ◽  
Palm Oil ◽  
Diesel Fuel ◽  
Thermal Efficiency ◽  
Engine Performance ◽  
Exhaust Emissions ◽  
Brake Specific Fuel Consumption ◽  
Brake Thermal Efficiency

Biofuels are an alternative fuel currently being developed to reduce the diesel-engine environmental impact. The release of carbon dioxide (CO2), nitric oxide (NO) and black smoke (BS) becomes an issue derived from diesel engines even in lean-mixture combustion causing an adverse effect to human health. The main aim of the research study is to present the use of biofuels, a mixture of diesel and 10 % palm oil ethyl ester (PEE10) and PEE10 blended with bioethanol from 5 to 20 %, compared with conventional diesel fuel. The biofuels were run on a high-speed direct injection diesel engine at a constant speed of 3,000 rpm under various loads. The use of PEE10 resulted in brake thermal efficiency (BTE) reduction by 2 % and brake specific fuel consumption (BSFC) incrementation by 8 %, but the exhaust emissions were lower than diesel, except for CO2 and NO. However, PEE10 engine performance was better and exhaust gas emissions were lower for both pollutants than diesel mixed with 10 % bioethanol. The investigation of PEE10 with increasing bioethanol revealed that the use of PEE10 blended with 5 % bioethanol (PEE10E5) can improve engine performance, while the BTE and BSFC were close to that of diesel, and exhaust emissions, especially CO2, NO and BS reduced. Moreover, BTE from PEE10E5 fueling increased by 2 % but BSFC was subtle increased, compared to PEE10. On the other hand, the increasing bioethanol from 10 to 20 % in PEE10 led to the more reduction in engine performance, but the engine pollutants were also continuously decreased. Specifically, the blend of PEE10 and 20 % bioethanol indicates that CO2, NO and BS were reduced by 10, 15 and 33 %, respectively, compared to diesel fuel. HIGHLIGHTS A mixture of diesel and 10 % palm oil ethyl ester (PEE10) has less exhaust emissions than diesel blended with 10 % palm oil methyl ester (PME10) PEE10 blended with 5 % bioethanol can improve engine performance, while the brake thermal efficiency and brake specific fuel consumption are close to that of diesel and PME10 The increasing bioethanol from 10 to 20 % in PEE10 leads to the more reduction in engine performance, but the engine pollutants, especially carbon dioxide, nitric oxide and black smoke, are also continuously decreased GRAPHICAL ABSTRACT

scholarly journals Thermal Performance of Compression Ignition Engine Using High Content Biodiesels: A Comparative Study with Diesel Fuel

2021 ◽  
Vol 13 (14) ◽  
pp. 7688
Author(s):  
Asif Afzal ◽  
Manzoore Elahi M. Soudagar ◽  
Ali Belhocine ◽  
Mohammed Kareemullah ◽  
Nazia Hossain ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fatty Acid Content ◽  
Engine Performance ◽  
Waste Cooking Oil ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Brake Thermal Efficiency ◽  
Acid Oil ◽  
Exhaust Gas Temperature

In this study, engine performance on thermal factors for different biodiesels has been studied and compared with diesel fuel. Biodiesels were produced from Pongamia pinnata (PP), Calophyllum inophyllum (CI), waste cooking oil (WCO), and acid oil. Depending on their free fatty acid content, they were subjected to the transesterification process to produce biodiesel. The main characterizations of density, calorific range, cloud, pour, flash and fire point followed by the viscosity of obtained biodiesels were conducted and compared with mineral diesel. The characterization results presented benefits near to standard diesel fuel. Then the proposed diesel engine was analyzed using four blends of higher concentrations of B50, B65, B80, and B100 to better substitute fuel for mineral diesel. For each blend, different biodiesels were compared, and the relative best performance of the biodiesel is concluded. This diesel engine was tested in terms of BSFC (brake-specific fuel consumption), BTE (brake thermal efficiency), and EGT (exhaust gas temperature) calculated with the obtained results. The B50 blend of acid oil provided the highest BTE compared to other biodiesels at all loads while B50 blend of WCO provided the lowest BSFC compared to other biodiesels, and B50 blends of all biodiesels provided a minimum % of the increase in EGT compared to diesel.

scholarly journals Effect of cetane improver addition into diesel fuel: Methanol mixtures on performance and emissions at different injection pressures

2017 ◽  
Vol 21 (1 Part B) ◽  
pp. 555-566 ◽  
Author(s):  
Feyyaz Candan ◽  
Murat Ciniviz ◽  
Ilker Ors
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Engine Performance ◽  
Injection Pressure ◽  
Specific Fuel Consumption ◽  
Exhaust Emission ◽  
Brake Specific Fuel Consumption ◽  
Consumption Values ◽  
Smoke Opacity

In this study, methanol in ratios of 5-10-15% were incorporated into diesel fuel with the aim of reducing harmful exhaust gasses of Diesel engine, di-tertbutyl peroxide as cetane improver in a ratio of 1% was added into mixture fuels in order to reduce negative effects of methanol on engine performance parameters, and isobutanol of a ratio of 1% was used as additive for preventing phase separation of all mixtures. As results of experiments conducted on a single cylinder and direct injection Diesel engine, methanol caused the increase of NOx emission while reducing CO, HC, CO2, and smoke opacity emissions. It also reduced torque and power values, and increased brake specific fuel consumption values. Cetane improver increased torque and power values slightly compared to methanol-mixed fuels, and reduced brake specific fuel consumption values. It also affected exhaust emission values positively, excluding smoke opacity. Increase of injector injection pressure affected performances of methanol-mixed fuels positively. It also increased injection pressure and NOx emissions, while reducing other exhaust emissions.

The Comparative Trail Research on the Performance of a Diesel Engine Fuelled with Diesel Fuel and Biodiesel/Diesel Blended Fuel

2011 ◽  
Vol 142 ◽  
pp. 103-106
Author(s):  
Wen Ming Cheng ◽  
Hui Xie ◽  
Gang Li
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Thermal Efficiency ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Brake Thermal Efficiency ◽  
Series Of Experiments ◽  
Blended Fuel ◽  
Load Conditions

This paper discusses the brake specific fuel consumption and brake thermal efficiency of a diesel engine using cottonseed biodiesel blended with diesel fuel. A series of experiments were conducted for the various blends under varying load conditions at a speed of 1500 rpm and 2500 rpm and the results were compared with the neat diesel. From the results, it is found that the brake specific fuel consumption of cottonseed biodiesel is slightly higher than that of diesel fuel at different engine loads and speeds, with this increase being higher the higher the percentage of the biodiesel in the blend. And the brake thermal efficiency of cottonseed biodiesel is nearly similar to that of diesel fuel at different engine loads and speeds. From the investigation, it is concluded that cottonseed biodiesl can be directly used in diesel engines without any modifications, at least in small blending ratios.

scholarly journals An Assessment on Performance Characteristics of Diesel Engine Using Lemongrass-Diesel Oil Fuel Blends

2021 ◽  
Author(s):  
Naveen Rana ◽  
Harikrishna Nagwan ◽  
Kannan Manickam
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Thermal Efficiency ◽  
Specific Fuel Consumption ◽  
Performance Characteristics ◽  
Emission Characteristics ◽  
Brake Specific Fuel Consumption ◽  
Brake Thermal Efficiency ◽  
Fuel Blends

Abstract Indeed, the development of alternative fuels for use in internal combustion engines has become an essential requirement to meet the energy demand and to deal with the different problems related to fuel. The research in this domain leads to the identification of adverse fuel properties and for their solution standard limits are being defined. This paper outlines an investigation of performance and combustion characteristics of a 4-stroke diesel engine using different cymbopogon (lemongrass) - diesel fuel blends. 10% to 40% cymbopogon is mixed with diesel fuel and tested for performance characteristics like brake specific fuel consumption and brake thermal efficiency. To obtain emission characteristics smoke density in the terms of HSU has been measured. In result, it has observed that there is an increase of 5% in brake thermal efficiency and 16.33% decrease in brake specific fuel consumption. Regarding emission characteristics, a 12.9% decrease in smoke emission has been found.

Experimental Study of Diesel Fuel Effects on Direct Injection (DI) Diesel Engine Performance and Pollutant Emissions

2007 ◽  
Vol 21 (5) ◽  
pp. 2642-2654 ◽  
Author(s):  
Theodoros C. Zannis ◽  
Dimitrios T. Hountalas ◽  
Roussos G. Papagiannakis
Keyword(s):  
Experimental Study ◽  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Engine Performance ◽  
Pollutant Emissions ◽  
Di Diesel Engine ◽  
Fuel Effects

scholarly journals The experimental investigation of diesel fuel-biofuel blends at different injection pressures in a DI diesel engine

2021 ◽  
Vol 9 (4A) ◽  
Author(s):  
İlker Örs ◽  
◽  
Murat Ciniviz ◽  
Bahar Sayin Kul ◽  
Ali Kahraman ◽  
...  
Keyword(s):  
Fuel Consumption ◽  
Diesel Fuel ◽  
Thermal Efficiency ◽  
Engine Performance ◽  
Injection Pressure ◽  
Exhaust Emissions ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Brake Thermal Efficiency ◽  
Injection Pressures

In this study, it was aimed to investigate the effects of a diesel-biodiesel blend (B20) and a diesel-biodiesel-bioethanol blend (BE5) on combustion parameters in addition to engine performance and exhaust emissions compared with diesel fuel. Parameters included in the evaluation was brake specific fuel consumption, brake thermal efficiency, CO, CO2, HC, NOx, smoke opacity emissions and finally cylinder pressure, heat release rate, ignition delay, some key points of the combustion phases such as start of ignition, start of combustion, CA50 and CA90 and combustion duration. Engine tests were conducted at different injection pressures of 170 bar, 190 bar, which is the original injection pressure, and 220 bar by the engine being loaded by 25, 50, 75 and 100% for the assessment of engine performance and exhaust emissions. For combustion evaluation, the data obtained at 1400 rpm, maximum torque-speed, and 2800 rpm, maximum power-speed were used, while the injection pressures were set to 170, 190 and 220 bar under full load condition. According to test results, the better performance characteristics, exhaust emissions and combustion behaviour of engine were obtained with the use of BE5 at high injection pressure. So, BE5 fuel improved brake specific fuel consumption by about 7% and brake thermal efficiency by about 6% compared to B20. In addition, while the emission values of BE5 gave better results than diesel fuel, it reduced the NOx and smoke emissions of B20 by approximately 1.4% and 6.4% respectively. Moreover, it has achieved a reduction in smoke emission of up to 45% compared to diesel fuel.

scholarly journals Engine performance and exhaust emission characteristics of paraffinic diesel fuel in a model diesel engine 

2018 ◽  
Vol 64 (No. 2) ◽  
pp. 85-95
Author(s):  
Jevič Petr ◽  
Pražan Radek ◽  
Šedivá Zdeňka
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Engine Performance ◽  
Exhaust Emission ◽  
Single Cylinder ◽  
Diesel Fuels ◽  
Single Cylinder Engine ◽  
Model Diesel ◽  
Fuel Mixtures ◽  
The Individual

The article deals with verification of a diesel fuel and two fuel mixtures blends with different amounts of the bio-component using the model single-cylinder engine without the additional equipment for treatment of exhaust gases. This combustion diesel engine served for measuring the performance characteristics of the model single-cylinder engine and the individual emission components in order to assess the use of these blends of liquid paraffinic diesel fuel in practice and to meet current and forthcoming European legislation and to fulfil the commitments by 2020. A detailed chemical analysis was performed in case of all the tested paraffinic diesel fuels. 

scholarly journals Experimental investigation of a small agricultural diesel engine performance using community biodiesel from wild trees

2020 ◽  
Vol 2 (1) ◽  
pp. 9-16
Author(s):  
Nigran Homdoung ◽  
Kittikorn Sasujit ◽  
Natthawud Dussadee ◽  
Rameshprabu Ramaraj
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fossil Fuels ◽  
Specific Energy Consumption ◽  
Engine Performance ◽  
Waste Cooking Oil ◽  
Exhaust Emission ◽  
Brake Thermal Efficiency ◽  
Cooking Oil ◽  
Wild Tree

The increasing consumption and demand for fossil fuels have more significance than before alarm above its lessening rate and for that reason, stimulated the actions are needed to challenge the issue with an efficient and less polluting alternative fuel for diesel. This study evaluated the performance of an 8.2 kW small diesel engine using three fuels, namely diesel, waste cooking oil biodiesel and wild tree biodiesel, such as granadilla oil biodiesel (GBD) and tung oil biodiesel (TBD). The experimental engine was tested at 1,500 rpm of constant engine speed and 20–80% of engine load. The specific fuel consumption, brake specific energy consumption, brake mean sufficient pressure, brake thermal efficiency, exhaust emission and temperature were evaluated. It was found that the small diesel engine worked well using wild trees biodiesel. The brake means effective pressures were lower by 5–8% and thermal brake efficiency was decreased in the range of 9–15%, compared with diesel fuel. The exhaust emission was lower than Thailand’s industrial standard and slightly higher than waste cooking oil biodiesel and diesel fuel operation. The operation of biodiesel from wild trees is suitable for farmers and is considered feasible for local communities in the future.

Sign in / Sign up

Export Citation Format

Share Document