3D Wind Field Construction for Suburban Environment by Parallel Computational Fluid Dynamics Techniques

2013 ◽  
Author(s):  
Yuntian Ge ◽  
Rui Zhang ◽  
Xiuling Wang
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Parallel Computing ◽  
Wind Farm ◽  
Cfd Simulations ◽  
Computing Technique ◽  
Geometry Model ◽  
Computational Fluid Dynamics Cfd ◽  
Simulation Results ◽  
Suburban Environment

The objective of this paper is to analysis the wind farm properties in suburban environment by Computational Fluid Dynamics (CFD) simulations. In order to do the simulation of a suburban environment, geometry model was built and mesh was generated by commercial software GAMBIT®. Simulation was conducted by FLUENT®. Parallel computing technique was applied in simulation. Simulation results showed different kinds of wind properties such as path lines, velocity distributions, turbulence intensity, etc., and it is also indicated that parallel computing is an appropriate way to conduct wind farm simulation [1].

scholarly journals Rapid pivot feeding in pipefish: flow effects on prey and evaluation of simple dynamic modelling via computational fluid dynamics

2008 ◽  
Vol 5 (28) ◽  
pp. 1291-1301 ◽  
Author(s):  
Sam Van Wassenbergh ◽  
Peter Aerts
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Analytical Model ◽  
Dynamic Modelling ◽  
Head Rotation ◽  
Theoretical Models ◽  
Cfd Simulations ◽  
Deceleration Phase ◽  
Computational Fluid Dynamics Cfd ◽  
Flow Effects

Most theoretical models of unsteady aquatic movement in organisms assume that including steady-state drag force and added mass approximates the hydrodynamic force exerted on an organism's body. However, animals often perform explosively quick movements where high accelerations are realized in a few milliseconds and are followed closely by rapid decelerations. For such highly unsteady movements, the accuracy of this modelling approach may be limited. This type of movement can be found during pivot feeding in pipefish that abruptly rotate their head and snout towards prey. We used computational fluid dynamics (CFD) to validate a simple analytical model of cranial rotation in pipefish. CFD simulations also allowed us to assess prey displacement by head rotation. CFD showed that the analytical model accurately calculates the forces exerted on the pipefish. Although the initial phase of acceleration changes the flow patterns during the subsequent deceleration phase, the accuracy of the analytical model was not reduced during this deceleration phase. Our analysis also showed that prey are left approximately stationary despite the quickly approaching pipefish snout. This suggests that pivot-feeding fish need little or no suction to compensate for the effects of the flow induced by cranial rotation.

scholarly journals Effect of hydraulic and geometric factors upon leakage flow rate in pressurized pipes

RBRH ◽  
2021 ◽  
Vol 26 ◽  
Author(s):  
Mayara Francisca da Silva ◽  
Fábio Veríssimo Gonçalves ◽  
Johannes Gérson Janzen
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Rate ◽  
Leakage Flow ◽  
Cfd Simulations ◽  
Mean Velocity ◽  
Leakage Flow Rate ◽  
Geometric Factors ◽  
Leakage Area ◽  
Computational Fluid Dynamics Cfd

ABSTRACT Computational Fluid Dynamics (CFD) simulations of a leakage in a pressurized pipe were undertaken to determine the empirical effects of hydraulic and geometric factors on the leakage flow rate. The results showed that pressure, leakage area and leakage form, influenced the leakage flow rate significantly, while pipe thickness and mean velocity did not influence the leakage flow rate. With relation to the interactions, the effect of pressure upon leakage flow rate depends on leakage area, being stronger for great leakage areas; the effects of leakage area and pressure on leakage flow rate is more pronounced for longitudinal leakages than for circular leakages. Finally, our results suggest that the equations that predict leakage flow rate in pressurized pipes may need a revision.

scholarly journals The Aerodynamics of a Diabolo

2021 ◽  
Author(s):  
Darren Jia
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Angular Momentum ◽  
Flow Pattern ◽  
High Spin ◽  
Angular Speed ◽  
Geometric Shape ◽  
Cfd Simulations ◽  
Resistive Torque ◽  
Computational Fluid Dynamics Cfd

Diabolo is a popular game in which the object can be spun at up to speeds of 5000 rpm. This high spin velocity gives the diabolo the necessary angular momentum to remain stable. The shape of the diabolo generates an interesting air flow pattern. The viscous air applies a resistive torque on the fast spinning diabolo. Through computational fluid dynamics (CFD) simulations it's shown that the resistive torque has an interesting dependence on the angular speed of the diabolo. Further, the geometric shape of the diabolo affects the dependence of torque on angular speed.

scholarly journals Comparison of Blade Element Method and CFD Simulations of a 10 MW Wind Turbine

Fluids ◽  
2018 ◽  
Vol 3 (4) ◽  
pp. 73 ◽  
Author(s):  
Galih Bangga
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Separation ◽  
Spatial Interpolation ◽  
Flow Conditions ◽  
Cfd Simulations ◽  
Computational Fluid Dynamics Cfd ◽  
Correction Terms ◽  
Selection Of ◽  
Blade Element

The present studies deliver the computational investigations of a 10 MW turbine with a diameter of 205.8 m developed within the framework of the AVATAR (Advanced Aerodynamic Tools for Large Rotors) project. The simulations were carried out using two methods with different fidelity levels, namely the computational fluid dynamics (CFD) and blade element and momentum (BEM) approaches. For this purpose, a new BEM code namely B-GO was developed employing several correction terms and three different polar and spatial interpolation options. Several flow conditions were considered in the simulations, ranging from the design condition to the off-design condition where massive flow separation takes place, challenging the validity of the BEM approach. An excellent agreement is obtained between the BEM computations and the 3D CFD results for all blade regions, even when massive flow separation occurs on the blade inboard area. The results demonstrate that the selection of the polar data can influence the accuracy of the BEM results significantly, where the 3D polar datasets extracted from the CFD simulations are considered the best. The BEM prediction depends on the interpolation order and the blade segment discretization.

scholarly journals Investigation of Influence of Adjustments in Cyclist Arm Position on Aerodynamic Drag Using Computational Fluid Dynamics

Proceedings ◽  
2020 ◽  
Vol 49 (1) ◽  
pp. 159
Author(s):  
Knut Erik Teigen Giljarhus ◽  
Daniel Årrestad Stave ◽  
Luca Oggiano
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Aerodynamic Drag ◽  
Time Trial ◽  
Elbow Extension ◽  
Cfd Simulations ◽  
Arm Position ◽  
Sport Activities ◽  
The Face ◽  
Computational Fluid Dynamics Cfd

In professional cycling, even small adjustments in position could mean that valuable seconds are gained over the course of a time-trial race. This study investigates the influence of arm position on the aerodynamic drag of a cyclist. Based on a 3D scanned model of a professional cyclist, 64 alternate positions are generated. The parameters that are investigated are the distance between elbows, elbow extension, and distance between hands. Computational fluid dynamics (CFD) simulations of all positions are performed, and a regression model is built from the results. The results indicate that the optimal posture is achieved for a minimum in all investigated parameters, which means that the hands and elbows should be kept together with hands up towards the face. Furthermore, elbow extension seems to be the most crucial parameter, followed by the distance between elbows, and then by the distance between the hands. The presented methodology can be applied to study other parameters relevant to cycling aerodynamics or be applied to other sport activities as well.

Optimal Hardware Placement in a Minitower Computer Enclosure System

2011 ◽  
Author(s):  
M. Alfaro Cano ◽  
A. Hernandez-Guerrero ◽  
C. Rubio Arana ◽  
Aristotel Popescu
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Cfd Simulation ◽  
Operating Temperature ◽  
Optimal Placement ◽  
Cfd Analysis ◽  
Computational Fluid Dynamics Cfd ◽  
Simulation Results ◽  
The Relationship ◽  
Key Questions

One of the requirements for existing personal computers, PCs, is that the hardware inside must maintain an operating temperature as low as possible. One way to achieve that is to place the hardware components at locations with enough airflow around it. However, the relationship between the airflow and temperature of the components is unknown before they are placed at specific locations inside a PC. In this work a Computational Fluid Dynamics (CFD) analysis is coupled to a Design of Experiment (DOE) methodology to answer typical minitower key questions: a) how do the possible positions of hardware components affect their temperature?, and b) is it possible to get an optimal placement for these hardware components using the data collected by the CFD simulation results? The DOE methodology is used to optimize the analysis for a very large number of possible configurations. The results help in identifying where the efforts need to be placed in order to optimize the positioning of the hardware components for similar configurations at the designing stage. Somehow the results show that general conclusions could be drawn, but that there are not specific rules that could be applied to every configuration.

Numerical and Experimental Study on a Honeycomb Ceramic Monolith

2012 ◽  
Vol 532-533 ◽  
pp. 431-435
Author(s):  
Chong Zhi Mao ◽  
Qian Jian Guo ◽  
Lei He
Keyword(s):  
Fluid Dynamics ◽  
Numerical Simulation ◽  
Experimental Study ◽  
Computational Fluid Dynamics ◽  
Flue Gas ◽  
Regenerative Process ◽  
Computational Fluid Dynamics Cfd ◽  
Simulation Results ◽  
Honeycomb Ceramic ◽  
Oxidation Reactor

Honeycomb ceramic is the key component of the regenerative system. The numerical simulation was performed using FLUENT, a commercial computational fluid dynamics (CFD) code, to compare simulation results to the test data. The regenerative process of a honeycomb ceramic regenerator was simulated under different conditions. Experiments were carried out on honeycomb regenerators that are contained in a methane oxidation reactor. The calculated temperatures of flue gas inlet were compared with the ones measured. The tendency of the temperature is the same as the experiment.

Sign in / Sign up

Export Citation Format

Share Document