Low Frequency Absorption of Additively Manufactured Cylinders

2019 ◽  
Author(s):  
Sophie R. Kaye ◽  
Ethan D. Casavant ◽  
Paul E. Slaboch
Keyword(s):  
Low Frequency ◽  
Normal Incidence ◽  
Frequency Noise ◽  
Outer Diameter ◽  
Acoustic Absorption ◽  
Frequency Range ◽  
Large Space ◽  
Low Frequencies ◽  
Cylinder Length ◽  
Hollow Cylinders

Abstract Attenuating low frequencies is often problematic, due to the large space required for common absorptive materials to mitigate such noise. However, natural hollow reeds are known to effectively attenuate low frequencies while occupying relatively little space compared to traditional absorptive materials. This paper discusses the effect of varied outer diameter, and outer spacing on the 200–1600 Hz acoustic absorption of additively manufactured arrays of hollow cylinders. Samples were tested in a 10 cm diameter normal incidence impedance tube such that cylinder length was oriented perpendicular to the incoming plane wave. By varying only one geometric element of each array, the absorption due to any particular parameter can be assessed individually. The tests confirmed the hypothesis that minimizing cylinder spacing and maximizing cylinder diameter resulted in increased overall absorption and produced more focused absorption peaks at specific low frequencies. Wider cylinder spacing produced a broader absorptive frequency range, despite shifting upward in frequency. Thus, manipulating these variables can specifically target absorption for low frequency noise that would otherwise disturb listeners.

Low-Frequency Acoustic Absorption of 3D Printed Cylinders

2020 ◽  
Vol 143 (1) ◽  
Author(s):  
Paul E. Slaboch ◽  
Sophie Kaye ◽  
Ethan Casavant
Keyword(s):  
Low Frequency ◽  
Normal Incidence ◽  
Frequency Noise ◽  
Outer Diameter ◽  
Acoustic Absorption ◽  
Large Space ◽  
Low Frequencies ◽  
Cylinder Length ◽  
3D Printed ◽  
Hollow Cylinders

Abstract Attenuating low-frequency sound is often problematic, due to the large space required for common absorptive materials to mitigate such noise. However, natural hollow reeds are known to effectively attenuate low frequencies while occupying relatively little space compared to traditional absorptive materials. The present study determines the effect of varied outer diameter and outer spacing on the 200–1600 Hz acoustic absorption of 3D printed arrays of hollow cylinders. Samples were tested in a 100-mm diameter normal incidence impedance tube such that cylinder length was oriented perpendicular to the incoming plane wave. By varying only one geometric element of each array, the absorption due to any parameter can be assessed individually. It was found that minimizing cylinder spacing and maximizing cylinder diameter resulted in increased overall absorption and produced more focused absorption peaks at specific low frequencies. Wider cylinder spacing produced a broader absorptive frequency range, despite shifting upward in frequency. Thus, manipulating these variables can specifically target absorption for low-frequency noise that would otherwise disturb listeners.

Low-frequency noise control using layered granular aerogel and limp porous media

2021 ◽  
Vol 263 (4) ◽  
pp. 2724-2729
Author(s):  
Yutong Xue ◽  
Amrutha Dasyam ◽  
J. Stuart Bolton ◽  
Bhisham Sharma
Keyword(s):  
Noise Control ◽  
Glass Fibers ◽  
Low Frequency ◽  
Normal Incidence ◽  
Frequency Noise ◽  
Fibrous Materials ◽  
Low Frequency Noise ◽  
Frequency Range ◽  
Fibrous Media ◽  
Impedance Tube Method

The acoustic absorption of granular aerogel layers with a granule sizes in the range of 2 to 40 μm is dominated by narrow-banded, high absorption regions in the low-frequency range and by reduced absorption values at higher frequencies. In this paper, we investigate the possibility of developing new, low-frequency noise reduction materials by layering granular aerogels with traditional porous sound absorbing materials such as glass fibers. The acoustic behavior of the layered configurations is predicted using the arbitrary coefficient method, wherein the granular aerogel layers are modeled as an equivalent poro-elastic material while the fibrous media and membrane are modeled as limp media. The analytical predictions are verified using experimental measurements conducted using the normal incidence, two-microphone impedance tube method. Our results show that layered configurations including granular aerogels, fibrous materials, and limp membranes provide enhanced sound absorption properties that can be tuned for specific noise control applications over a broad frequency range.

Analysis of an Ultra-Low Frequency and Ultra-Broadband Phononic Crystals Silencer with Small Size

2019 ◽  
Vol 27 (02) ◽  
pp. 1850026 ◽  
Author(s):  
Jiangwei Liu ◽  
Dianlong Yu ◽  
Jihong Wen ◽  
Zhenfang Zhang
Keyword(s):  
Wave Propagation ◽  
Periodic Structures ◽  
Low Frequency ◽  
Phononic Crystals ◽  
Frequency Noise ◽  
Duct System ◽  
Frequency Range ◽  
Expansion Chamber ◽  
Band Formation ◽  
Low Frequencies

Existing research shows that acoustic BG in a certain frequency range can be realized by installing an expansion chamber on duct system, but the problems of broadband and size limitations at low frequencies remain to be researched. The study of acoustic and elastic wave propagation in artificial periodic structures has received increasing attention for many decades, and the presence of bandgap (BG) in phononic crystals (PCs), which inhibits elastic/acoustic wave propagation within the BG’ frequency range, supplies a new way to control noise and vibrations in duct system. Based on PC theory, a duct silencer backed with a gas–liquid expansion chamber is proposed to enhance the acoustic performance of low-frequency noise attenuation. The transfer matrix method (TMM) is used to investigate the acoustic BG properties. The influences on the BG properties of some key parameters are analyzed, and the band formation mechanism is revealed by the law of energy conservation. The results show that silencers with a small size can effectively attenuate ultra-low frequencies and ultra-broad bands.

scholarly journals On articulated plates with micro-slits to tackle low-frequency noise

Acta Acustica ◽  
2021 ◽  
Vol 5 ◽  
pp. 31
Author(s):  
Massimo Emiliano D’Elia ◽  
Thomas Humbert ◽  
Yves Aurégan
Keyword(s):  
Low Frequency ◽  
Normal Incidence ◽  
Frequency Noise ◽  
Correct Identification ◽  
Low Frequency Noise ◽  
Perfect Absorption ◽  
Flow Measurements ◽  
Low Frequencies ◽  
Acoustic Liner ◽  
Acoustic Treatment

In recent years, new concepts of acoustic absorbers dedicated to the reduction of low-frequency noise have been developed. Among them, liners with moving parts, such as membrane-based liners, have been an object of particular interest. In the present paper, we propose a liner concept based on a cantilever beam made of articulated plates with micro-slits. Compared to membrane technologies, these micro-slits introduce a small leakage from the backing cavity that reduces the high compressibility effects occurring at very low frequencies in a small cavity. An acoustic liner including an ensemble of such articulated plates has been fabricated and characterized for grazing acoustic incidence in absence and in presence of flow. Measurements in an impedance tube at normal incidence have also been performed, and perfect absorption is obtained at a frequency where the liner thickness corresponds to 1/16th of the acoustic wavelength. A new and simple model is proposed to predict the attenuation of this type of acoustic treatment. The results are in good agreement with the measurements, indicating a correct identification of the physical phenomena here at stake.

A waveform inversion technique for measuring elastic wave attenuation in cylindrical bars

Geophysics ◽  
1992 ◽  
Vol 57 (6) ◽  
pp. 854-859 ◽  
Author(s):  
Xiao Ming Tang
Keyword(s):  
Elastic Wave ◽  
Wave Attenuation ◽  
Waveform Inversion ◽  
Finite Size ◽  
Low Frequency ◽  
Frequency Range ◽  
Multiple Reflections ◽  
Low Frequencies ◽  
The Time Domain ◽  
Attenuation Values

A new technique for measuring elastic wave attenuation in the frequency range of 10–150 kHz consists of measuring low‐frequency waveforms using two cylindrical bars of the same material but of different lengths. The attenuation is obtained through two steps. In the first, the waveform measured within the shorter bar is propagated to the length of the longer bar, and the distortion of the waveform due to the dispersion effect of the cylindrical waveguide is compensated. The second step is the inversion for the attenuation or Q of the bar material by minimizing the difference between the waveform propagated from the shorter bar and the waveform measured within the longer bar. The waveform inversion is performed in the time domain, and the waveforms can be appropriately truncated to avoid multiple reflections due to the finite size of the (shorter) sample, allowing attenuation to be measured at long wavelengths or low frequencies. The frequency range in which this technique operates fills the gap between the resonant bar measurement (∼10 kHz) and ultrasonic measurement (∼100–1000 kHz). By using the technique, attenuation values in a PVC (a highly attenuative) material and in Sierra White granite were measured in the frequency range of 40–140 kHz. The obtained attenuation values for the two materials are found to be reliable and consistent.

Optimally Sensitive and Efficient Compact Loudspeakers for Low Audio Frequencies

2007 ◽  
Vol 38 (7) ◽  
pp. 11-17
Author(s):  
Ronald M. Aarts
Keyword(s):  
Optimality Criterion ◽  
Low Frequency ◽  
Audio Signal ◽  
Design Procedure ◽  
Frequency Range ◽  
Force Factor ◽  
Low Frequencies ◽  
Limited Frequency ◽  
The Cost ◽  
Higher Sensitivity

Conventionally, the ultimate goal in loudspeaker design has been to obtain a flat frequency response over a specified frequency range. This can be achieved by carefully selecting the main loudspeaker parameters such as the enclosure volume, the cone diameter, the moving mass and the very crucial “force factor”. For loudspeakers in small cabinets the results of this design procedure appear to be quite inefficient, especially at low frequencies. This paper describes a new solution to this problem. It consists of the combination of a highly non-linear preprocessing of the audio signal and the use of a so called low-force-factor loudspeaker. This combination yields a strongly increased efficiency, at least over a limited frequency range, at the cost of a somewhat altered sound quality. An analytically tractable optimality criterion has been defined and has been verified by the design of an experimental loudspeaker. This has a much higher efficiency and a higher sensitivity than current low-frequency loudspeakers, while its cabinet can be much smaller.

Low Frequency Noise Annoyance Assessment by Low Frequency Noise Rating (LFNR) Curves

1983 ◽  
Vol 2 (1) ◽  
pp. 20-28 ◽  
Author(s):  
N. Broner ◽  
H.G. Leventhall
Keyword(s):  
Laboratory Experiments ◽  
Low Frequency ◽  
Frequency Noise ◽  
Low Frequency Noise ◽  
Low Frequencies ◽  
Noise Annoyance

Over recent years, it has become apparent that low frequency noise annoyance is more widespread than originally believed. Annoyance has occurred where the emitted noise is unbalanced towards the low frequencies even though the dB(A) level has been low. Following laboratory experiments carried out as part of an investigation into low frequency annoyance, combined with field annoyance data, the Low Frequency Noise Rating (LFNR) curves are proposed for the assessment of low frequency noise annoyance complaints.

scholarly journals Low Frequency Noise Remove from EEG Signal

2020 ◽  
Vol 9 (1) ◽  
pp. 1510-1513
Keyword(s):  
Human Brain ◽  
Random Noise ◽  
Low Frequency ◽  
Frequency Noise ◽  
Eeg Signal ◽  
Low Frequency Noise ◽  
Frequency Range ◽  
Average Value ◽  
Different Types ◽  
The Brain

The electrical activity of the brain recorded by EEG which used to detect different types of diseases and disorders of the human brain. There is contained a large amount of random noise present during EEG recording, such as artifacts and baseline changes. These noises affect the low -frequency range of the EEG signal. These artifacts hiding some valuable information during analyzing of the EEG signal. In this paper we used the FIR filter for removing low -frequency noise(<1Hz) from the EEG signal. The performance is measured by calculating the SNR and the RMSE. We obtained RMSE average value from the test is 0.08 and the SNR value at frequency(<1Hz) is 0.0190.

scholarly journals Implementation of the Spectral Method for Determining of Measuring Instruments' Dynamic Characteristics

2020 ◽  
Vol 11 (2) ◽  
pp. 155-162
Author(s):  
A. F. Sabitov ◽  
I. A. Safina
Keyword(s):  
Dynamic Response ◽  
Spectral Method ◽  
Amplitude Spectrum ◽  
Low Frequency ◽  
Signal Amplitude ◽  
Measuring Instruments ◽  
Frequency Noise ◽  
Frequency Range ◽  
Calculated Amplitude ◽  
Zero Frequency

The spectral method for establishing dynamic response of measuring instruments basically requires determining the amplitude spectrum of the signal in its informative part that includes the amplitude spectrum at zero frequency. The operating frequency range of existing low-frequency spectrum analyzers is above zero frequency that leads to an uncertainty in dynamic response of measuring instruments determined by the spectral method. The purpose of this paper is to develop a program for calculating the signal amplitude spectrum, starting from zero frequency, to implement a spectral method for determining the dynamic response of measuring instruments on computers equipped with the MatLab package.To implement the spectral method for determining the dynamic response of measuring instruments, we developed a program in the MatLab 2013b environment that determines the signal amplitude spectrum from zero Hertz. The program reads the source data from Excel tables and presents the calculated amplitude spectrum as a chart and a report table.It is shown that the developed program calculates the signal amplitude spectrum with a standard deviation of not more than 3.4 % in the frequency range of 0 to 10 rad/s. The calculated amplitude spectrum allows determining the time constant of first-order aperiodic measuring instruments with an uncertainty of not more than 0.166 % at any noise level, if their frequencies are outside the information part of the spectrum.We demonstrated the claimed advantage of the spectral method for determining dynamic response using the developed program by the example of a high-frequency noise in the transient response of some measuring instruments.

scholarly journals A census of the pulsar population observed with the international LOFAR station FR606 at low frequencies (25–80 MHz)

2020 ◽  
Vol 635 ◽  
pp. A76 ◽  
Author(s):  
L. Bondonneau ◽  
J.-M. Grießmeier ◽  
G. Theureau ◽  
A. V. Bilous ◽  
V. I. Kondratiev ◽  
...  
Keyword(s):  
Low Frequency ◽  
Frequency Range ◽  
Radio Pulsars ◽  
Low Frequencies ◽  
Radio Observatory ◽  
Future Studies ◽  
New Information ◽  
Upper Limits ◽  
Widespread Phenomenon ◽  
First Time

Context. To date, only 69 pulsars have been identified with a detected pulsed radio emission below 100 MHz. A LOFAR-core LBA census and a dedicated campaign with the Nançay LOFAR station in stand-alone mode were carried out in the years 2014–2017 in order to extend the known population in this frequency range. Aims. In this paper, we aim to extend the sample of known radio pulsars at low frequencies and to produce a catalogue in the frequency range of 25–80 MHz. This will allow future studies to probe the local Galactic pulsar population, in addition to helping explain their emission mechanism, better characterising the low-frequency turnover in their spectra, and obtaining new information about the interstellar medium through the study of dispersion, scattering, and scintillation. Methods. We observed 102 pulsars that are known to emit radio pulses below 200 MHz and with declination above −30°. We used the Low Band Antennas (LBA) of the LOw Frequency ARray (LOFAR) international station FR606 at the Nançay Radio Observatory in stand-alone mode, recording data between 25 and 80 MHz. Results. Out of our sample of 102 pulsars, we detected 64. We confirmed the existence of ten pulsars detected below 100 MHz by the LOFAR LBA census for the first time (Bilous et al. 2020, A&A, 635, A75) and we added two more pulsars that had never before been detected in this frequency range. We provided average pulse profiles, DM values, and mean flux densities (or upper limits in the case of non-detections). The comparison with previously published results allows us to identify a hitherto unknown spectral turnover for five pulsars, confirming the expectation that spectral turnovers are a widespread phenomenon.

Sign in / Sign up

Export Citation Format

Share Document