Increasing the Productivity of Solar Photovoltaic Systems

Author(s):  
David A. Torrey ◽  
James M. Kokernak

State-sponsored incentives have played a significant role in driving the demand for residential and small commercial photovoltaic (PV) systems. All state incentive programs are tied to the power rating of the system, though some states also offer energy production incentives. Unfortunately, there is a disconnect between the power rating of a PV system and the energy that system produces over its lifetime. It is extremely important to consider system productivity, which goes well beyond the efficiency of the components. System productivity is tied directly to the structure of the array, not just the efficiency of the components and the quality of the installation. This paper examines the issues associated with improving solar PV system productivity. The focus is on comparing a series-parallel array configuration to a series-string array configuration and the impact on energy production. Partial shade is used to highlight substantial differences between the operation of the two array configurations.

Author(s):  
Rakesh Dalal ◽  
Kamal Bansal ◽  
Sapan Thapar

Rooftop solar photovoltaic(PV) installation in India have increased in last decade because of the flat 40 percent subsidy extended for rooftop solar PV systems (3 kWp and below) by the Indian government under the solar rooftop scheme. From the residential building owner's perspective, solar PV is competitive when it can produce electricity at a cost less than or equal grid electricity price, a condition referred as “grid parity”. For assessing grid parity of 3 kWp and 2 kWp residential solar PV system, 15 states capital and 19 major cities were considered  for the RET screen simulation by using solar isolation, utility grid tariff, system cost and other economic parameters. 3 kWp and 2 kWp rooftop solar PV with and without subsidy scenarios were considered for simulation using RETscreen software. We estimate that without subsidy no state could achieve grid parity for 2kWp rooftop solar PV plant. However with 3 kWp rooftop solar PV plant only 5 states could achieve grid parity without subsidy and with government subsidy number of states increased to 7, yet wide spread parity for residential rooftop solar PV is still not achieved. We find that high installation costs, subsidized utility grid supply to low energy consumer and financing rates are major barriers to grid parity.


Electronics ◽  
2019 ◽  
Vol 8 (12) ◽  
pp. 1443 ◽  
Author(s):  
Abdullah Alshahrani ◽  
Siddig Omer ◽  
Yuehong Su ◽  
Elamin Mohamed ◽  
Saleh Alotaibi

Decarbonisation, energy security and expanding energy access are the main driving forces behind the worldwide increasing attention in renewable energy. This paper focuses on the solar photovoltaic (PV) technology because, currently, it has the most attention in the energy sector due to the sharp drop in the solar PV system cost, which was one of the main barriers of PV large-scale deployment. Firstly, this paper extensively reviews the technical challenges, potential technical solutions and the research carried out in integrating high shares of small-scale PV systems into the distribution network of the grid in order to give a clearer picture of the impact since most of the PV systems installations were at small scales and connected into the distribution network. The paper reviews the localised technical challenges, grid stability challenges and technical solutions on integrating large-scale PV systems into the transmission network of the grid. In addition, the current practices for managing the variability of large-scale PV systems by the grid operators are discussed. Finally, this paper concludes by summarising the critical technical aspects facing the integration of the PV system depending on their size into the grid, in which it provides a strong point of reference and a useful framework for the researchers planning to exploit this field further on.


2012 ◽  
Author(s):  
Firdaus Muhammad Sukki ◽  
Roberto Ramirez Iniguez ◽  
Scott G. Mcmeekin ◽  
Brian G. Stewart ◽  
Barry Clive

Solar energy has become a matter of global attention in the past few years. This paper explores the use and benefit of solar concentrators in the solar photovoltaic (PV) systems. First, a short literature review of previous research on the usage of solar concentrators in improving solar PV system performance and reducing the cost of implementation is presented. This is followed by an overview of SolarBrane, an example of a Building Integrated photovoltaic (BIPV) system which uses an optical concentrator in the solar PV design. An optimised design of the SolarBrane is also discussed afterwards. A financial benefit study is conducted to compare the average return of investment of using the optimised SolarBrane and traditional solar PV installed in Malaysia’s environment. SolarBrane has proven to be a good alternative to achieve costeffective solar PV system. The financial analysis simulated under the new Malaysian Feed–In Tariff scheme indicates that the optimised SolarBrane could potentially reduce the initial cost of implementation by 40% and generate higher return, close to 20%, when compared to traditional solar PV systems. Key words: Solar photovoltaic; solar concentrator; solarBrane; dielectric totally internally reflecting concentrator; financial analysis


The need to electrify all rural areas in India is quite compelling. However, the focus has now shifted from traditional fuel-based systems to generate electricity to renewable sources for energy generation. Though there are subsidies and policies that encourage the use of solar Photovoltaic (PV) systems, there is a need for an appropriate framework. This framework could not only offer substantial directions but it would also act as grounds to enhance rural electrification in India using solar PVs. From this perspective, the current research attempts to structure an innovative framework for solar PV system that could facilitate rural electrification in India. In particular, the district of Damoh in Madhya Pradesh was chosen as there are many villages without electricity in this district. PVsyst software was utilized to simulate the outcomes that included mathematical models and diverse components based on PV, for simulation. Three designs were developed to facilitate the simulation. These included; PVs linked with microgrid devoid of battery, individual PV systems without microgrid link and solar PVs linked to microgrid with battey. The framework for rural electrification using solar PVs will offer policy makers with insights with regards to implementing PV systems. It will also offer inputs as to the feasibility of implementing a specific system on several parameters. These would comprise of; number of households within a village, detached households etc. Nonetheless, research in future is also warranted to explore the scope for other sources of renewable energy.


2021 ◽  
pp. 1-32
Author(s):  
Mohammad Hamed ◽  
Adnan AlMasri ◽  
Zakariya Dalala ◽  
Raed Alsaleh

Abstract This paper addresses two key decisions by households to adopt rooftop solar PV systems and the length of time until the adoption. It is hypothesized that these decisions are controlled by different mechanisms and should be modelled independently. This is the first attempt to formally estimate the length of time until the adoption to the authors' knowledge. Two models are presented in this paper. The first is a mixed logit to model the respondents' intention to adopt a solar PV system, and the second is a random parameters ordered probit to estimate the length of time until the adoption. Estimation results show that the number of electrical appliances, the households' interest to harness economic benefits, and the type and characteristics of the dwelling motivate households to select a shorter duration until the adoption. Results also show that the majority (77.80%) of respondents with EVs are highly likely to adopt a rooftop system and select a shorter time duration until adoption. In addition, a significant proportion (83.23%) of respondents with high monthly electricity bills are more likely to adopt a rooftop PV system and select a shorter time duration. Results show that the average monthly electricity bill for households with a PV system has decreased by 74.04%. Reducing monthly electricity bills is a key instigator for adopting a rooftop PV system. Our results confirm the hypothesis that even if there is an intent to adopt a rooftop solar PV system, the length of time until the adoption is controlled by another mechanism.


2016 ◽  
Vol 5 (3) ◽  
pp. 179-185 ◽  
Author(s):  
Jeffrey Tamba Dellosa

The Renewable Energy Act of 2008 in the Philippines provided an impetus for residential owners to explore solar PV installations at their own rooftops through the Net-Metering policy. The Net-Metering implementation through the law however presented some concerns with inexperienced electric DU on the potential effect of high residential solar PV system installations. It was not known how a high degree of solar integration to the grid can possibly affect the operations of the electric DU in terms of energy load management. The primary objective of this study was to help the local electric DU in the analysis of the potential effect of high residential solar PV system penetration to the supply and demand load profile in an electric distribution utility (DU) grid in the province of Agusan del Norte, Philippines. The energy consumption profiles in the year 2015 were obtained from the electric DU operating in the area. An average daily energy demand load profile was obtained from 0-hr to the 24th hour of the day based from the figures provided by the electric DU. The assessment part of the potential effect of high solar PV system integration assumed four potential total capacities from 10 Mega Watts (MW) to 40 MW generated by all subscribers in the area under study at a 10 MW interval. The effect of these capacities were measured and analyzed with respect to the average daily load profile of the DU. Results of this study showed that a combined installations beyond 20 MWp coming from all subscribers is not viable for the local electric DU based on their current energy demand or load profile. Based from the results obtained, the electric DU can make better decisions in the management of high capacity penetration of solar PV systems in the future, including investment in storage systems when extra capacities are generated.Article History: Received July 15th 2016; Received in revised form Sept 23rd 2016; Accepted Oct 1st 2016; Available onlineHow to Cite This Article: Dellosa, J. (2016) Potential Effect and Analysis of High Residential Solar Photovoltaic (PV) Systems Penetration to an Electric Distribution Utility (DU). Int. Journal of Renewable Energy Development, 5(3), 179-185.http://dx.doi.org/10.14710/ijred.5.3.179-185


Energies ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2137
Author(s):  
Mariz B. Arias ◽  
Sungwoo Bae

This paper provides models for managing and investigating the power flow of a grid-connected solar photovoltaic (PV) system with an energy storage system (ESS) supplying the residential load. This paper presents a combination of models in forecasting solar PV power, forecasting load power, and determining battery capacity of the ESS, to improve the overall quality of the power flow management of a grid-connected solar PV system. Big data tools were used to formulate the solar PV power forecasting model and load power forecasting model, in which real historical solar electricity data of actual solar homes in Australia were used to improve the quality of the forecasting models. In addition, the time-of-use electricity pricing was also considered in managing the power flow, to provide the minimum cost of electricity from the grid to the residential load. The output of this model presents the power flow profiles, including the solar PV power, battery power, grid power, and load power of weekend and weekday in a summer season. The battery state-of-charge of the ESS was also presented. Therefore, this model may help power system engineers to investigate the power flow of each system of a grid-connected solar PV system and help in the management decision for the improvement of the overall quality of the power management of the system.


Energies ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 169
Author(s):  
Oluwaseun M. Akeyo ◽  
Aron Patrick ◽  
Dan M. Ionel

Significant changes in conventional generator operation and transmission system planning will be required to accommodate increasing solar photovoltaic (PV) penetration. There is a limit to the maximum amount of solar that can be connected in a service area without the need for significant upgrades to the existing generation and transmission infrastructure. This study proposes a framework for analyzing the impact of increasing solar penetration on generation and transmission networks while considering the responses of conventional generators to changes in solar PV output power. Contrary to traditional approaches in which it is assumed that generation can always match demand, this framework employs a detailed minute-to-minute (M-M) dispatch model capable of capturing the impact of renewable intermittency and estimating the over- and under-generation dispatch scenarios due to solar volatility and surplus generation. The impact of high solar PV penetration was evaluated on a modified benchmark model, which includes generators with defined characteristics including unit ramp rates, heat rates, operation cost curves, and minimum and maximum generation limits. The PV hosting capacity, defined as the maximum solar PV penetration the system can support without substantial generation imbalances, transmission bus voltage, or thermal violation was estimated for the example transmission circuit considered. The results of the study indicate that increasing solar penetration may lead to a substantial increase in generation imbalances and the maximum solar PV system that can be connected to a transmission circuit varies based on the point of interconnection, load, and the connected generator specifications and responses.


2021 ◽  
Vol 2021 ◽  
pp. 1-14
Author(s):  
Estifanos Abeje Sharew ◽  
Habtemariam Aberie Kefale ◽  
Yalew Gebru Werkie

The electrical energy demand is steadily growing, and hence, the integration of photovoltaic system to the distribution networks is also dramatically increasing though it has a significant effect on the network’s power quality. The purpose of this paper is to analyze the impact of solar PV integration on the power quality of distribution networks. The study is conducted using ETAP software, taking one of the radial distribution networks available in Bahir Dar city during the peak of connected loads which has the least voltage profile. Furthermore, the optimal location of the PV in the network is done using particle swarm optimization. Accordingly, the appropriate location of the PV system is determined to be the farthest end bus (bus 34). Also, the impact in terms of voltage and current harmonic distortion on the distribution feeder network is comparatively discussed by comparing the distribution system parameters with different penetration levels of solar PV system. The simulation results obtained demonstrate that high harmonic distortion level is injected correspondingly as the penetration capacity of PV system increased which indicates that the solar PV system should be integrating only up to a maximum possible capacity the network can carry. The integration of the PV system beyond this maximum penetration level causes production of high harmonic distortion which adversely affects the system performance. At the maximum penetration level which allows the acceptable harmonic distortion limit, the total voltage harmonic distortion and current demand distortion are found to be 4.97% and 14.98%, respectively.


2019 ◽  
Vol 25 ◽  
pp. 1-19
Author(s):  
Sindri Þrastarson ◽  
Björn Marteinsson ◽  
Hrund Ólöf Andradóttir

The efficiency and production costs of solar panels have improved dramatically in the past decades. The Nordic countries have taken steps in instigating photovoltaic (PV) systems into energy production despite limited incoming solar radiation in winter. IKEA installed the first major PV system in Iceland with 65 solar panels with 17.55 kW of production capacity in the summer of 2018. The purpose of this research was to assess the feasibility of PV systems in Reykjavík based on solar irradiation measurements, energy production of a PV array located at IKEA and theory. Results suggests that net irradiation in Reykjavík (64°N, 21° V) was on average about 780 kWh/m2 per year (based on years 2008-2018), highest 140 kWh/m2 in July and lowest 1,8 kWh/m2 in December. Maximum annual solar power is generated by solar panels installed at a 40° fixed angle. PV panels at a lower angle produce more energy during summer. Conversely, higher angles maximize production in the winter. The PV system produced over 12 MWh over a one-year period and annual specific yield was 712 kWh/kW and performance ratio 69% which is about 10% lower than in similar studies in cold climates. That difference can be explained by snow cover, shadow falling on the panels and panels not being fixed at optimal slope. Payback time for the IKEA PV system was calculated 24 years which considers low electricity prices in Reykjavik and unforeseen high installation costs. Solar energy could be a feasible option in the future if production- and installation costs were to decrease and if the solar PV output could be sold to the electric grid in Iceland.


Sign in / Sign up

Export Citation Format

Share Document