Numerical Analysis of Active Vibro-Acoustic Control in an Enclosed Cavity

2012 ◽  
Author(s):  
Wael Elwali ◽  
Mingfeng Li ◽  
Teik C. Lim
Keyword(s):  
Transfer Functions ◽  
Low Frequency ◽  
Region Of Interest ◽  
Acoustic Energy ◽  
Structural Vibration ◽  
Acoustic Cavity ◽  
Acoustic Control ◽  
Applied Forces ◽  
Cavity Acoustics ◽  
Control Forces

A numerical model is applied to study the application of active vibro-acoustic control in an enclosed cavity. The vibro-acoustic problem is composed of a free-free beam, representing the windshield, coupled with a rectangular planar acoustic cavity, representing the passenger compartment. Forces at the windshield boundaries are actively applied to reduce noise due to floor panel vibrations and sound from a monopole source. Noise transfer functions are used to calculate the control forces based on their ability to minimize the acoustic energy distribution in the total region and within the region of interest. Results show that noise is substantially reduced in the low frequency range accompanied with some reduction at the higher frequencies as well. Results also show that applied forces based on partial area control have more potential in reducing noise within the region of interest than those based on global area control. It was also observed that this control strategy performs better in vibration induced noise problems than in monopole source problems. The proposed model can be applied to noise control problems involving the transmission of vibratory energy into a cavity through fluid-structural coupling that relates structural vibration to cavity acoustics.

Active Control of Sound Radiation Into Enclosures Using Structural Error Sensors

2002 ◽  
Author(s):  
D. S. Li ◽  
L. Cheng ◽  
C. M. Gosselin
Keyword(s):  
Genetic Algorithms ◽  
Active Control ◽  
Polyvinylidene Fluoride ◽  
Design Method ◽  
Low Frequency ◽  
Acoustic Energy ◽  
Sensor Design ◽  
Optimal Theory ◽  
Structural Surface ◽  
Control Forces

Active control of vibration and sound inside a structure-surrounded enclosure leads to many applications such as noise control inside vehicle cabins. Despite the extensive research carried out in the last two decades, ANVC technology is still in its infancy and has not yet been introduced massively in practical engineering applications. One of the problems to be resolved is that most of presently used techniques require the use of microphones inside the cavity, which is not practical in many situations. In addition, due to the coupling between the vibrating structure and the confined enclosure, demand for more robust control strategy is apparent. This paper tackles the aforementioned problem using a benchmark system in which only PVDF (Polymer polyvinylidene fluoride) sensors are used on the structural surface. A new method based on genetic algorithms is developed for sensor design. This design process ensures a proper consideration of the acoustic energy in the enclosure without the direct use of acoustic sensors inside the cavity. Roughly speaking, the sensor is designed to capture the most radiating motion of the structure via an automatic optimization process. In the proposed method, Genetic Algorithms and the least quadratic square optimal theory are organically combined together. For each configuration of error sensors, the amplitude of control forces, which can either be point forces or excitation generated by piezoceramic actuators, is first determined by minimizing the sum of the squared outputs of error sensors using the least quadratic square optimal theory. Then with the optimal amplitude of control forces, the acoustic potential energy of the sound cavity is computed and used as the evaluation criteria in the evolution process. Using Genetic Algorithms, the optimal configuration of the error sensors can be determined. A cylindrical shell with an internal floor partition is used as an example to illustrate the effectiveness of the proposed approach. To increase the computational efficiency, the structural surface is assumed to be covered with strip-typed PVDF sensors along both the circumferential and longitudinal directions. Both numerical and experimental results show the great effectiveness of the proposed GA-based design method. The sound reduction is achieved not only at the design frequency but also at most frequencies in the low frequency range. The proposed method demonstrates great merits in sensor design for complex structures.

Collective oscillations in bubble clouds

2011 ◽  
Vol 680 ◽  
pp. 114-149 ◽  
Author(s):  
ZORANA ZERAVCIC ◽  
DETLEF LOHSE ◽  
WIM VAN SAARLOOS
Keyword(s):  
Frequency Response ◽  
Acoustic Field ◽  
Low Frequency ◽  
Acoustic Energy ◽  
Viscous Damping ◽  
Edge States ◽  
Bubble Cloud ◽  
Collective Oscillations ◽  
The Individual ◽  
Bubble Oscillations

In this paper the collective oscillations of a bubble cloud in an acoustic field are theoretically analysed with concepts and techniques of condensed matter physics. More specifically, we will calculate the eigenmodes and their excitabilities, eigenfrequencies, densities of states, responses, absorption and participation ratios to better understand the collective dynamics of coupled bubbles and address the question of possible localization of acoustic energy in the bubble cloud. The radial oscillations of the individual bubbles in the acoustic field are described by coupled linearized Rayleigh–Plesset equations. We explore the effects of viscous damping, distance between bubbles, polydispersity, geometric disorder, size of the bubbles and size of the cloud. For large enough clusters, the collective response is often very different from that of a typical mode, as the frequency response of each mode is sufficiently wide that many modes are excited when the cloud is driven by ultrasound. The reason is the strong effect of viscosity on the collective mode response, which is surprising, as viscous damping effects are small for single-bubble oscillations in water. Localization of acoustic energy is only found in the case of substantial bubble size polydispersity or geometric disorder. The lack of localization for a weak disorder is traced back to the long-range 1/r interaction potential between the individual bubbles. The results of the present paper are connected to recent experimental observations of collective bubble oscillations in a two-dimensional bubble cloud, where pronounced edge states and a pronounced low-frequency response had been observed, both consistent with the present theoretical findings. Finally, an outlook to future possible experiments is given.

An efficient low-frequency acoustic energy harvester

2017 ◽  
Vol 264 ◽  
pp. 84-89 ◽  
Author(s):  
Ming Yuan ◽  
Ziping Cao ◽  
Jun Luo ◽  
Jinya Zhang ◽  
Cheng Chang
Keyword(s):  
Energy Harvester ◽  
Low Frequency ◽  
Acoustic Energy

scholarly journals Study on Vibration Transmission among Units in Underground Powerhouse of a Hydropower Station

Energies ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 3015 ◽  
Author(s):  
Jijian Lian ◽  
Hongzhen Wang ◽  
Haijun Wang
Keyword(s):  
Low Frequency ◽  
Field Tests ◽  
Vertical Vibration ◽  
Transmission Mechanism ◽  
Structural Vibration ◽  
Hydropower Station ◽  
Fe Model ◽  
Vibration Transmission ◽  
Underground Powerhouse ◽  
Mechanical Models

Research on the safety of powerhouse in a hydropower station is mostly concentrated on the vibration of machinery structure and concrete structure within a single unit. However, few studies have been focused on the vibration transmission among units. Due to the integrity of the powerhouse and the interaction, it is necessary to study the vibration transmission mechanism of powerhouse structure among units. In this paper, field structural vibration tests are conducted in an underground powerhouse of a hydropower station on Yalong River. Additionally, the simplified mechanical models are established to explain the transmission mechanism theoretically. Moreover, a complementary finite element (FE) model is built to replicate the testing conditions for comprehensive analysis. The field tests results show that: (1) the transmission of lateral-river vibration is greater than those of longitude-river vibration and vertical vibration; (2) the vibration transmission of the vibrations that is caused by the low frequency tail fluctuation is basically equal to that of the vibrations caused by rotation of hydraulic generator. The transmission mechanism is demonstrated by the simplified mechanical models and is verified by the FE results. This study can provide guidance for further research on the vibration of underground powerhouse structure.

scholarly journals Identification and Removal of Non-acoustic Noise in Towed Array Sonar Using F-Κ Transform for Enhanced Torpedo Detection

2020 ◽  
Vol 14 ◽  
Keyword(s):  
Vibration Isolation ◽  
Acoustic Noise ◽  
Detection System ◽  
Mechanical Vibration ◽  
Low Frequency ◽  
Acoustic Energy ◽  
Noise Sources ◽  
Towed Array ◽  
Spatio Temporal ◽  
Towed Arrays

Low frequency passive towed array sonar is an essential component in a torpedo detection system for surface ships. Compact towed arrays are used for torpedo detection and they will be towed at higher towing speeds compared to conventional towed array sonars used for surveillance. Presence of non-acoustic noise in towed array sensors at higher towing speeds degrades torpedo detection capability at lower frequencies. High wavenumber mechanical vibrations are induced in the array by vortex shedding associated with hydrodynamic flow over the array body and cable scope. These vibrations are known to couple into the hydrophone array as nonacoustic noise sources and can impair acoustic detection performance, particularly in the forward end fire direction. Lengthy mechanical vibration isolation modules can isolate vibration induced noise in towed arrays, but this is not recommended in a towed array which is towed at high speeds as it will increase the drag and system complexity. An algorithm for decomposing acoustic and non-acoustic components of signals received at sensor level using well known frequency-wavenumber transform (F-K transform) is presented here. Frequency-wavenumber diagrams can be used for differentiating between acoustic and non-acoustic signals. An area of V shape is identified within the F-K spectrum where acoustic energy is confined. Energy outside this V will highlight non-acoustic energy. Enhanced simultaneous spatio-temporal and spatio-amplitude detection is possible with this algorithm. Performance of this algorithm is validated through simulation and experimental data.

scholarly journals CLUSTER–STAFF search coil magnetometer calibration – comparisons with FGM

2014 ◽  
Vol 3 (2) ◽  
pp. 153-177 ◽  
Author(s):  
P. Robert ◽  
N. Cornilleau-Wehrlin ◽  
R. Piberne ◽  
Y. de Conchy ◽  
C. Lacombe ◽  
...  
Keyword(s):  
Transfer Functions ◽  
Low Frequency ◽  
Temporal Analysis ◽  
Fluxgate Magnetometer ◽  
Data Sets ◽  
Spectral Matrix ◽  
Spatio Temporal ◽  
Cross Calibration ◽  
The Waves ◽  
The Way

Abstract. The main part of the Cluster Spatio-Temporal Analysis of Field Fluctuations (STAFF) experiment consists of triaxial search coils allowing the measurements of the three magnetic components of the waves from 0.1 Hz up to 4 kHz. Two sets of data are produced, one by a module to filter and transmit the corresponding waveform up to either 10 or 180 Hz (STAFF-SC), and the second by the onboard Spectrum Analyser (STAFF-SA) to compute the elements of the spectral matrix for five components of the waves, 3 × B and 2 × E (from the EFW experiment), in the frequency range 8 Hz to 4 kHz. In order to understand the way the output signals of the search coils are calibrated, the transfer functions of the different parts of the instrument are described as well as the way to transform telemetry data into physical units across various coordinate systems from the spinning sensors to a fixed and known frame. The instrument sensitivity is discussed. Cross-calibration inside STAFF (SC and SA) is presented. Results of cross-calibration between the STAFF search coils and the Cluster Fluxgate Magnetometer (FGM) data are discussed. It is shown that these cross-calibrations lead to an agreement between both data sets at low frequency within a 2% error. By means of statistics done over 10 yr, it is shown that the functionalities and characteristics of both instruments have not changed during this period.

scholarly journals The Influence of PZT Actuators Positioning in Active Structural Acoustic Control

10.14311/968 ◽  
2007 ◽  
Vol 47 (4-5) ◽  
Author(s):  
P. Švec ◽  
V. Jandák
Keyword(s):  
Sound Field ◽  
Structural Vibration ◽  
Structural Acoustics ◽  
The Finite Element Method ◽  
Ansys Software ◽  
Structural Vibrations ◽  
Radiated Power ◽  
Acoustic Control ◽  
Radiated Sound ◽  
The Mathematical Model

This paper deals with the effect of secondary actuator positioning in an active structural acoustics control (ASAC) experiment. The ASAC approach is based on minimizing the sound radiation from structures to the far field by controlling the structural vibrations. In this article a rectangular steel plate structure was assumed with one secondary actuator attached to it. As a secondary actuator, a specially designed piezoelectric stripe actuator was used. We studied the effect of the position of the actuator on the pattern and on the radiated sound field of the structural vibration, with and without active control. The total radiated power was also measured. The experimental data was confronted with the results obtained by a numerical solution of the mathematical model used. For the solution, the finite element method in the ANSYS software package was used. 

Experimental Research about the Application of ER Elastomer in the Shock Absorber

2013 ◽  
Vol 641-642 ◽  
pp. 371-376 ◽  
Author(s):  
Shi Sha Zhu ◽  
Xue Peng Qian ◽  
Hao He ◽  
Quan Fu Zhang
Keyword(s):  
Electric Field ◽  
External Electric Field ◽  
Shock Absorber ◽  
Hybrid Control ◽  
Excitation Frequency ◽  
Low Frequency ◽  
Structural Vibration ◽  
Shear Mode ◽  
Response Performance ◽  
Better Than

When the Electrorheological elastomer (ERE) is embedded into intelligence structure system, the structure damping and stiffness of the system can be changed quickly and reversibly under an external electric field. Thus, the application of the Electrorheological elastomer in the active and passive hybrid control of structural vibration has already attracted people's wide attention. In this paper, three types of ER elastomer were prepared based on barium titanate, starch, then the microstructure of ER elastomer was observed and the mechanical properties were analyzed; a shear mode ERE shock absorber was designed, the vibration response performance of which was experimentally evaluated under various excitation frequency with or without the applied field. The experimental results showed that the damping and stiffness of the shock absorber could be modified with a changing external electric field, whose macro-features was that the damping coefficient increased with the increase of the electric field, and the damping effect in the high frequency was better than in the low frequency.

Structural Source Identification from Acoustic Measurements Using an Energetic Approach

2017 ◽  
Vol 34 (4) ◽  
pp. 431-441 ◽  
Author(s):  
A. Samet ◽  
M. A. Ben Souf ◽  
O. Bareille ◽  
M. N. Ichchou ◽  
T. Fakhfakh ◽  
...  
Keyword(s):  
Energy Method ◽  
Numerical Test ◽  
Acoustic Energy ◽  
Vibration Source ◽  
Radiated Noise ◽  
Acoustic Cavity ◽  
Energetic Approach ◽  
Structural Force ◽  
Noise Measurements ◽  
Acoustic Energy Density

AbstractAn inverse energy method for the identification of the structural force in high frequency ranges from radiated noise measurements is presented in this paper. The radiation of acoustic energy of the structure coupled to an acoustic cavity is treated using an energetic method called the simplified energy method. The main novelty of this paper consists in using the same energy method to solve inverse structural problem. It consists of localization and quantification of the vibration source through the knowledge of acoustic energy density. Numerical test cases with different measurement points are used for validation purpose. The numerical results show that the proposed method has an excellent performance in detecting the structural force with a few acoustical measurements.

Sign in / Sign up

Export Citation Format

Share Document