Unit Cell Sparger Test Program and Preliminary Test Results for APR1400

2002 ◽  
Author(s):  
Choon-Kyung Park ◽  
Seok Cho ◽  
Chul-Hwa Song ◽  
Se-Young Chun
Keyword(s):  
Preliminary Test ◽  
Test Results ◽  
Test Program ◽  
Flow Area ◽  
Water Level Variation ◽  
Air Bubble ◽  
Discharge Line ◽  
Test Parameters ◽  
Hydraulic Load ◽  
Valve Opening

KAERI has performed a series of blowdown tests to assess the performance of prototypic steam sparger which will be used in a APR1400 reactor. The test program consists of 22 blowdown tests and each test simulates air clearing phase during an opening of depressurization valves. The major test parameters include air mass in the discharge line, air temperature, flow area, valve opening time, IRWST water temperature, and submergence of a sparger. The CPT-3 test was conducted for typical PWR condition. Following valve actuation, the pressure within the discharge line underwent pressure transient and the discharged high pressure air formed air bubbles, which expanded and compressed periodically in the simulated IRWST. Loop behavior as well as hydraulic load caused by air bubble oscillation during the air clearing phase were described. In addition, water level variation in the sparger during operation of a vacuum breaker was also discussed.

DAYA TAHAN ROTAN YANG DIAWETKAN DENGAN CUKA KAYU GALAM TERHADAP SERANGAN BUBUK Dinoderus minutus Farb.

2010 ◽  
Vol 2 (2) ◽  
pp. 8
Author(s):  
Evy Setiawati
Keyword(s):  
Force Feedback ◽  
Test Results ◽  
Dry Powder ◽  
Degree Of Protection ◽  
Wood Vinegar ◽  
Dinoderus Minutus ◽  
Test Parameters ◽  
Feedback Method ◽  
Reduction Percentage ◽  
Insect Attack

Rattan on frequently attacked by the powder post beetle (Tellu, 2001). The prevention of dry powder attacks is done by preservation. The increasing resistant of rattan from insect attack can be done by an environmentally friendly preservative, the Galam wood vinegar. This research  aims to determine the most effective concentration of preservative that shows the lowest attacks level of D. Farb minutus powder. The rattan used is green rattan (Calamus sp.) The concentration of preservative that are used:10%, 40%, 70% and 100%. The testing of dry powder attack  used force feedback method. The effectiveness test parameters of wood vinegar to dry powder attacks  included degree of protection Dinoderus minutus Farb. powder,  reduction percentage of rattan weight and the mortality of dry powder Dinoderus sp for toxicological testing of wood vinegar. The test results showed that the degree of protection powder in rattan growing along with the increased concentration of preservatives. The higher the concentration of  wood vinegar, the smaller the reduction of rattan weight and the higher the mortality rate of dry powder. Keywords: resistant of rattan, wood vinegar, Dinoderus minutus.

Modeling the Tensile Behaviour of a SiC/SiC Composite by Master Curves

2000 ◽  
Author(s):  
J. Shi
Keyword(s):  
Master Curve ◽  
Ceramic Matrix Composites ◽  
Test Material ◽  
Tensile Behaviour ◽  
Matrix Composites ◽  
Test Results ◽  
Master Curves ◽  
The Past ◽  
Test Parameters ◽  
Tensile Data

Scatter in test results is common for relatively brittle materials such as ceramic matrix composites. The scatter may come from differences in material processing conditions, specimen machining/handling and from variations in test parameters for nominally the same test material. Large scatter in test results makes material modeling difficult. In the past, master curve concepts have been proposed to reduce scatter in tensile data and to interpret fatigue/creep results. In this paper, one such concept is examined in detail by applying it to the recent tensile test results of a SiC/SiC composite. It was found that the way to construct master curves did not apply to the CMC studied and thus a new master curve was developed to better represent the tensile data. In addition, the test data were analysed statistically based on the new master curve.

analysis of mechanical properties of ceiling boards based on corn cobs and coconut coir waste with latex adhesive

2021 ◽  
Vol 5 (2) ◽  
pp. 1
Author(s):  
Ety Jumiati ◽  
Ufik Eliati Tumanggor ◽  
Abdul Halim Daulay
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Fracture Strength ◽  
Test Results ◽  
Hot Press ◽  
Optimal Result ◽  
Corn Cob ◽  
Corn Cobs ◽  
Test Parameters ◽  
Coconut Coir

<p align="center"><strong><em>Abstract</em></strong></p><p>Ceiling evelopment by utilizing waste corn cobs, coconut coir with gypsum flour an the adition of latex adhesive. Variations in the composition of the mixture of corn cobs, coconut coir, gypsum flour with latex adhesive include sample A (0:0:100:15), sample B (3:3:94:15), sample C (6:6:88:15), sample D (9:9:82:15), sample E (12:12:76:15), and sample F (15:15:70:15) with emphasis using a <em>hot press </em>and drying for 28 days. The test parameters include flexural strength and fracture strength. The test results show that sample B in the composition (3:3:94:15) is the optimal result. In this composition, the resulting ceiling board has the characteristics of a flexural strength of 3966,39 kgf/cm<sup>2</sup> and a fracture strength of 1088,6 kgf/cm<sup>2</sup>.</p><p><strong><em>Keyword :</em></strong><em> Lateks , Ceiling Board, Coconut Coir, Corn Cob</em></p><p><em> </em></p>

Durability of BFRP and Hybrid FRP Sheets under Freeze-Thaw Cycling

2010 ◽  
Vol 163-167 ◽  
pp. 3297-3300 ◽  
Author(s):  
Jia Wei Shi ◽  
Hong Zhu ◽  
Zhi Shen Wu ◽  
Gang Wu
Keyword(s):  
Mechanical Properties ◽  
Test Data ◽  
Mechanical Characteristics ◽  
Test Results ◽  
Freeze Thaw ◽  
Frp Composites ◽  
Test Parameters ◽  
The Stability ◽  
Better Than

Coupon tests were conducted to investigate the mechanical characteristics of basalt FRP (BFRP) sheet, basalt-carbon hybrid FRP sheets and the corresponding epoxy rein under the effect of freeze-thaw cycling. FRP sheets and epoxy rein coupons were subjected to up to 200 and 250 freeze-thaw cycles respectively. Test parameters included the number of freeze-thaw cycles and the types of FRP composites. Test results show that (1) BFRP sheet perform better than CFRP or GFRP sheets under high freeze-thaw cycles; (2) exposed hybrid FRP sheets not only show very little loss in mechanical properties, but also contribute to the stability of test data; (3) mechanical properties of rein epoxy decrease significantly with increasing freeze-thaw cycles.

Study of the effect of test parameters on the assessment of steel resistance to carbon dioxide corrosion

2021 ◽  
Vol 87 (12) ◽  
pp. 36-41
Author(s):  
A. S. Fedorov ◽  
E. L. Alekseeva ◽  
A. A. Alkhimenko ◽  
N. O. Shaposhnikov ◽  
M. A. Kovalev
Keyword(s):  
Carbon Dioxide ◽  
Laboratory Tests ◽  
Oil And Gas ◽  
Oil And Gas Industry ◽  
Sample Surface ◽  
Test Results ◽  
Carbon Dioxide Corrosion ◽  
Gas Industry ◽  
Test Parameters ◽  
Repeatability And Reproducibility

Carbon dioxide (CO2) corrosion is one of the most dangerous types of destruction of metal products in the oil and gas industry. The field steel pipelines and tubing run the highest risk. Laboratory tests are carried out to assess the resistance of steels to carbon dioxide corrosion. However, unified requirements for certain test parameters are currently absent in the regulatory documentation. We present the results of studying the effect of the parameters of laboratory tests on the assessment of the resistance of steels to CO2 corrosion. It is shown that change in the parameters of CO2 concentration, chemical composition of the water/brine system, the buffer properties and pH, the roughness of the sample surface, etc., even in the framework of the same laboratory technique, can lead in different test results. The main contribution to the repeatability and reproducibility of test results is made by the concentration of CO2, pH of the water/brine system, and surface roughness of the samples. The results obtained can be used in developing recommendations for the choice of test parameters to ensure a satisfactory convergence of the results gained in different laboratories, as well as in elaborating of a unified method for assessing the resistance of steels to carbon dioxide corrosion.

Sign in / Sign up

Export Citation Format

Share Document